Seagate ST3146807FC, ST336607FC, ST373307FC manual Drive mounting, Air flow

Page 45

Cheetah 10K.6 FC Product Manual, Rev. B

35

created while providing air flow to the electronics and HDA. Also, the shortest possible path between the air inlet and exit should be chosen to minimize the travel length of air heated by the drive and other heat sources within the rack, cabinet, or drawer environment.

If forced air is determined to be necessary, possible air-flow patterns are shown in Figure 18. The air-flow pat- terns are created by one or more fans, either forcing or drawing air as shown in the illustrations. Conduction, convection, or other forced air-flow patterns are acceptable as long as the temperature measurement guide- lines of Section 6.3.1 are met.

Above unit

Under unit

Note. Air flows in the direction shown (front to back) or in reverse direction (back to front)

 

Above unit

Note. Air flows in the direction shown or

Under unit

in reverse direction (side to side)

 

Figure 18.

Air flow

8.5Drive mounting

Mount the drive using the bottom or side mounting holes. If you mount the drive using the bottom holes, ensure that you do not physically distort the drive by attempting to mount it on a stiff, non-flat surface.

The allowable mounting surface stiffness is 80 lb/in (14.0 N/mm). The following equation and paragraph define the allowable mounting surface stiffness:

K x X = F < 15lb = 67N

where K is the mounting surface stiffness (units in lb/in or N/mm) and X is the out-of-plane surface distortion (units in inches or millimeters). The out-of-plane distortion (X) is determined by defining a plane with three of the four mounting points fixed and evaluating the out-of-plane deflection of the fourth mounting point when a known force (F) is applied to the fourth point.

Note. Before mounting the drive in any kind of 3.5-inch to 5.25-inch adapter frame, verify with Seagate Tech- nology that the drive can meet the shock and vibration specifications given herein while mounted in such an adapter frame. Adapter frames that are available may not have a mechanical structure capa- ble of mounting the drive so that it can meet the shock and vibration specifications listed in this manual.

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Page Page Page Page Revision Date Writer/Engineer Sheets Affected Revision status summary sheetPage Contents Installation Defect and error managementSeagate Technology support services Interface requirementsCheetah 10K.6 FC Product Manual, Rev. B Vii List of FiguresPage Cheetah 10K.6 FC family disc drive ScopeCheetah 10K.6 FC Product Manual, Rev. B Applicable standards and reference documentation Korean MIC Australian C-TickTaiwanese Bsmi Reference documentsCheetah 10K.6 FC disc drive General descriptionMedia description Standard featuresPerformance ReliabilityFactory-installed options Factory-installed accessoriesUser-installed accessories Unformatted and formatted capacitiesCheetah 10K.6 FC Product Manual, Rev. B Internal drive characteristics Performance characteristicsSeek performance characteristics Access time Format command execution time in minutesStart/stop time General performance characteristicsPrefetch/multi-segmented cache control Cache operationCaching write data Prefetch operation Reliability specifications Preventive maintenance Reliability and serviceService life Service philosophy7 S.M.A.R.T Controlling S.M.A.R.TPerformance impact Reporting control MillisecondsDetermining rate Predictive failuresImplementation State of the drive prior to testingInvoking DST Short and extended testsLog page entries Product warrantyAbort ShippingAC power requirements Physical/electrical specificationsDC power requirements General DC power requirement notesConducted noise immunity Power sequencingCurrent profiles +5V +12VTypical ST373307FC drive +12V current profile Typical ST3146807FC drive +5V current profile Typical ST373307FC drive +5V current profile ST373307FC Power dissipation ST3146807FCCheetah 10K.6 FC Product Manual, Rev. B ST336607FC TemperatureEffective altitude sea level Relative humidityShock and vibration ShockPackage size Packaged/product weight Drop height Recommended mounting Air cleanliness Cheetah 10K.6 FC Product Manual, Rev. B VibrationAcoustics Mounting configuration dimensions Mechanical specificationsDefect and error management Drive internal defects/errorsDrive error recovery procedures FC-AL system errors Read retry Maximum recovery time per Write retryRead and write retry count maximum recovery times Maximum recovery time perInstallation Drive ID/option selectionLED connections Drive Front 1 J6 connector requirementsDrive orientation CoolingAir flow Drive mountingGrounding Fibre Channel link service frames FC-AL featuresInterface requirements Fibre Channel task management functionsNPort login Plogi payload Bytes Fibre Channel port loginFibre Channel Process Login Accept Fibre Channel Process LoginNPort Login Accept ACC payload Bytes Process Login Plri payloadFabric Login Flogi payload Bytes Fibre Channel fabric loginAccept or NPort Login when sending frames to an initiator Fabric Login Accept ACC payload BytesDual port support Fibre Channel Arbitrated Loop optionsFC-AL options supported Option SupportedSupported commands Command code Command name Command code Supported Command name Supported commandsRead descriptor mode Cheetah 10K.6 FC Product Manual, Rev. B Cheetah 10K.6 FC Product Manual, Rev. B Inquiry data Mode Sense dataCheetah 10K.6 FC inquiry data Bytes Data hexCheetah 10K.6 FC Product Manual, Rev. B DEF DEF CHG Cheetah 10K.6 FC Product Manual, Rev. B Miscellaneous features Miscellaneous operating features and conditionsSupported Feature or condition Miscellaneous statusPhysical description Physical characteristicsPart description Positions Part number Features Connector requirementsPin Signal name Signal type Pin descriptionsFC-SCA pin descriptions Fault LED Out PowerFC-AL transmitters and receivers Active LED OutEnable port bypass signals Motor start controls11 SEL6 through SEL0 ID lines Parallel Enclosure Services Interface ESI Setting Setting Hex DecArbitrated loop physical address Alpa values TTL input characteristics Signal characteristicsLED driver signals Device control codesDifferential Pecl input Transmit eye diagramLink rate GHz Eye diagram data valuesAutomated Services Seagate Technology support services Online ServicesPresales Support Technical SupportCustomer Service CSO USA/Canada/Latin America Support ServicesEuropean Support Services Africa/Middle East Support Services Asia/Pacific Support ServicesCall Center Toll-free Direct dial Cheetah 10K.6 FC Product Manual, Rev. B Index FC-AL Cheetah 10K.6 FC Product Manual, Rev. B Plogi Cheetah 10K.6 FC Product Manual, Rev. B Cheetah 10K.6 FC Product Manual, Rev. B
Related manuals
Manual 2 pages 5.2 Kb

ST336607FC, ST373307FC, ST3146807FC specifications

The Seagate ST373307FC, ST3146807FC, and ST336607FC are robust hard disk drives designed for enterprise environments where reliability and performance are critical. Each model offers distinct features suited to various data storage needs, reflecting Seagate's commitment to innovation in storage technology.

The ST373307FC is a 73GB Fibre Channel hard drive that operates at 15,000 RPM, making it exceptionally fast for read and write operations. This drive employs a 4GB cache, enhancing its performance by allowing quicker access to frequently used data. With a 3.5-inch form factor, the ST373307FC is built for high-density environments, delivering reliable access to data. Its Fibre Channel interface supports high-speed connections, essential for data-intensive applications like databases and virtualization.

Next in line, the ST3146807FC offers a capacity of 146GB, also operating at 15,000 RPM. This drive features an 8GB cache, which significantly improves its data transfer rates, making it ideal for transactional workloads. The ST3146807FC is engineered to minimize latency and maximize throughput, ensuring that enterprises can access critical data swiftly and efficiently. Additionally, its rugged construction is designed to withstand the demands of continuous operation, providing peace of mind for businesses with strict uptime requirements.

Lastly, the ST336607FC has a substantial storage capacity of 300GB and shares the 15,000 RPM operational speed that characterizes this high-performance line. With a similar 8GB cache as the ST3146807FC, it offers excellent performance for read-intensive and write-heavy applications. The ST336607FC is also designed with enhanced thermal management features, supporting cooler operations in densely packed server environments. This model is particularly suited for applications such as data warehousing and online transaction processing, where speed and reliability are paramount.

Each of these drives utilizes advanced technologies like Native Command Queuing (NCQ), which optimizes the order of read and write requests. These features, combined with Seagate's reputation for durability and performance, make the ST373307FC, ST3146807FC, and ST336607FC excellent choices for enterprise applications requiring high-speed data access and exceptional reliability. In environments where data integrity and uptime are critical, these drives provide the robust performance necessary to meet demanding storage needs.
Top Page Image Contents