Seagate ST373307FC manual Drive Front, 1 J6 connector requirements, Drive orientation, Cooling

Page 44

34

Cheetah 10K.6 FC Product Manual, Rev. B

Drive

Front

Pin 1

J6

Reserved

Port A Bypass LED [1]

Port B Bypass LED [1]

Fault LED [1]

Reserved

Active LED [2]

Reserved

+5V

Active LED [1]

Ground [3]

[1]The drive has a 1.2K ohm resistor in series with this LED driver. Tie the minus side of an external high-efficiency LED (i.e., 2ma) to this pin. Connect the plus side of the LED to +5V.

[2]An external current-limiting resistor is required when connecting an LED to this pin. The minus side of the resistor/LED combination is connected to this pin. Connect the plus side to +5V.

[3]Jumper storage location (across pins 2 and 4).

Figure 17. LED indicator connector

8.2.1J6 connector requirements

Recommended mating connector part number: Berg receptacle, 6-position, Berg part number 690-006.

8.3Drive orientation

The drive may be mounted in any orientation. All drive performance characterizations, however, have been done with the drive in horizontal (discs level) and vertical (drive on its side) orientations, which are the two pre- ferred mounting orientations.

8.4Cooling

Cabinet cooling must be designed by the customer so that the ambient temperature immediately surrounding the drive will not exceed temperature conditions specified in Section 6.3.1, "Temperature."

The rack, cabinet, or drawer environment for the drive must provide heat removal from the electronics and head and disc assembly (HDA). You should confirm that adequate heat removal is provided using the tempera- ture measurement guidelines described in Section 6.3.1.

Forced air flow may be required to keep temperatures at or below the temperatures specified in Section 6.3.1, in which case the drive should be oriented, or air flow directed, so that the least amount of air flow resistance is

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Page Page Page Page Revision status summary sheet Revision Date Writer/Engineer Sheets AffectedPage Contents Defect and error management InstallationSeagate Technology support services Interface requirementsList of Figures Cheetah 10K.6 FC Product Manual, Rev. B ViiPage Scope Cheetah 10K.6 FC family disc driveCheetah 10K.6 FC Product Manual, Rev. B Applicable standards and reference documentation Australian C-Tick Korean MICTaiwanese Bsmi Reference documentsGeneral description Cheetah 10K.6 FC disc driveStandard features Media descriptionPerformance ReliabilityFactory-installed accessories Factory-installed optionsUser-installed accessories Unformatted and formatted capacitiesCheetah 10K.6 FC Product Manual, Rev. B Performance characteristics Internal drive characteristicsSeek performance characteristics Access time Format command execution time in minutesGeneral performance characteristics Start/stop timePrefetch/multi-segmented cache control Cache operationCaching write data Prefetch operation Reliability specifications Reliability and service Preventive maintenanceService life Service philosophyPerformance impact 7 S.M.A.R.TControlling S.M.A.R.T Milliseconds Reporting controlDetermining rate Predictive failuresState of the drive prior to testing ImplementationInvoking DST Short and extended testsProduct warranty Log page entriesAbort ShippingPhysical/electrical specifications AC power requirementsDC power requirements General DC power requirement notesPower sequencing Conducted noise immunityCurrent profiles +5V +12VTypical ST373307FC drive +12V current profile Typical ST3146807FC drive +5V current profile Typical ST373307FC drive +5V current profile Power dissipation ST3146807FC ST373307FCTemperature Cheetah 10K.6 FC Product Manual, Rev. B ST336607FCRelative humidity Effective altitude sea levelShock and vibration ShockPackage size Packaged/product weight Drop height Recommended mounting Acoustics Air cleanlinessCheetah 10K.6 FC Product Manual, Rev. B Vibration Mechanical specifications Mounting configuration dimensionsDrive error recovery procedures Defect and error managementDrive internal defects/errors Read retry Maximum recovery time per Write retry FC-AL system errorsRead and write retry count maximum recovery times Maximum recovery time perLED connections InstallationDrive ID/option selection 1 J6 connector requirements Drive FrontDrive orientation CoolingDrive mounting Air flowGrounding FC-AL features Fibre Channel link service framesInterface requirements Fibre Channel task management functionsFibre Channel port login NPort login Plogi payload BytesFibre Channel Process Login Fibre Channel Process Login AcceptNPort Login Accept ACC payload Bytes Process Login Plri payloadFibre Channel fabric login Fabric Login Flogi payload BytesFabric Login Accept ACC payload Bytes Accept or NPort Login when sending frames to an initiatorFibre Channel Arbitrated Loop options Dual port supportFC-AL options supported Option SupportedSupported commands Command code Command name Supported commands Command code Supported Command nameRead descriptor mode Cheetah 10K.6 FC Product Manual, Rev. B Mode Sense data Cheetah 10K.6 FC Product Manual, Rev. B Inquiry dataCheetah 10K.6 FC inquiry data Bytes Data hexCheetah 10K.6 FC Product Manual, Rev. B DEF DEF CHG Cheetah 10K.6 FC Product Manual, Rev. B Miscellaneous operating features and conditions Miscellaneous featuresSupported Feature or condition Miscellaneous statusPhysical characteristics Physical descriptionConnector requirements Part description Positions Part number FeaturesFC-SCA pin descriptions Pin Signal name Signal typePin descriptions Power Fault LED OutFC-AL transmitters and receivers Active LED Out11 SEL6 through SEL0 ID lines Enable port bypass signalsMotor start controls Parallel Enclosure Services Interface ESI Arbitrated loop physical address Alpa values SettingSetting Hex Dec Signal characteristics TTL input characteristicsLED driver signals Device control codesTransmit eye diagram Differential Pecl inputEye diagram data values Link rate GHzSeagate Technology support services Online Services Automated ServicesPresales Support Technical SupportEuropean Support Services Customer Service CSOUSA/Canada/Latin America Support Services Call Center Toll-free Direct dial Africa/Middle East Support ServicesAsia/Pacific Support Services Cheetah 10K.6 FC Product Manual, Rev. B Index FC-AL Cheetah 10K.6 FC Product Manual, Rev. B Plogi Cheetah 10K.6 FC Product Manual, Rev. B Cheetah 10K.6 FC Product Manual, Rev. B
Related manuals
Manual 2 pages 5.2 Kb

ST336607FC, ST373307FC, ST3146807FC specifications

The Seagate ST373307FC, ST3146807FC, and ST336607FC are robust hard disk drives designed for enterprise environments where reliability and performance are critical. Each model offers distinct features suited to various data storage needs, reflecting Seagate's commitment to innovation in storage technology.

The ST373307FC is a 73GB Fibre Channel hard drive that operates at 15,000 RPM, making it exceptionally fast for read and write operations. This drive employs a 4GB cache, enhancing its performance by allowing quicker access to frequently used data. With a 3.5-inch form factor, the ST373307FC is built for high-density environments, delivering reliable access to data. Its Fibre Channel interface supports high-speed connections, essential for data-intensive applications like databases and virtualization.

Next in line, the ST3146807FC offers a capacity of 146GB, also operating at 15,000 RPM. This drive features an 8GB cache, which significantly improves its data transfer rates, making it ideal for transactional workloads. The ST3146807FC is engineered to minimize latency and maximize throughput, ensuring that enterprises can access critical data swiftly and efficiently. Additionally, its rugged construction is designed to withstand the demands of continuous operation, providing peace of mind for businesses with strict uptime requirements.

Lastly, the ST336607FC has a substantial storage capacity of 300GB and shares the 15,000 RPM operational speed that characterizes this high-performance line. With a similar 8GB cache as the ST3146807FC, it offers excellent performance for read-intensive and write-heavy applications. The ST336607FC is also designed with enhanced thermal management features, supporting cooler operations in densely packed server environments. This model is particularly suited for applications such as data warehousing and online transaction processing, where speed and reliability are paramount.

Each of these drives utilizes advanced technologies like Native Command Queuing (NCQ), which optimizes the order of read and write requests. These features, combined with Seagate's reputation for durability and performance, make the ST373307FC, ST3146807FC, and ST336607FC excellent choices for enterprise applications requiring high-speed data access and exceptional reliability. In environments where data integrity and uptime are critical, these drives provide the robust performance necessary to meet demanding storage needs.
Top Page Image Contents