Seagate ST3146807FC manual FC-AL transmitters and receivers, Power, Fault LED Out, Active LED Out

Page 66

56

Cheetah 10K.6 FC Product Manual, Rev. B

9.5.5FC-AL transmitters and receivers

A typical FC-AL differential copper transmitter and receiver pair is shown in Figure 23. The receiver is required to provide the AC coupling to eliminate ground shift noise.

TX

68

 

.01

RX

 

Differential

 

Transmitter

150

150

Receiver

Transfer Medium

TY

 

 

RY

68

 

 

 

 

.01

 

150

 

 

 

 

 

 

 

Figure 23. FC-AL transmitters and receivers

9.5.6Power

Power is supplied through the FC-SCA with support for +5 volts and +12 volts. All of the voltage pins in the drive connector are the same length.

Four 12 volt pins provide +12 volt power to the drive. The current return for the +12 volt power supply is through the common ground pins. The supply current and return current must be distributed as evenly as possible among the pins. The maximum current typically occurs while the drive motor is starting.

Three 5 volt pins provide logic power to the drive. The current return for the +5 volt power supply is through the common ground pins. Distribute supply and return current as evenly as possible among the voltage and ground pins.

The mating connector pins use shorter contacts to achieve power surge reductions and to aid in “hot plugging” the drives. There are longer voltage contacts in the connector to enable the drive filter capacitors to charge. Current to the drive through the long charge pins is limited by the system in which the drive operates. Three of the +12 volt pins are shorter to allow capacitive pre-charging through the longer +12 volt charge pin. Two of the +5 volt pins are shorter to allow capacitive precharging through the longer +5 volt charge pin.

9.5.7Fault LED Out

The Fault LED Out signal is driven by the drive when:

•the drive detects failure of both ports

•the drive detects an internal failure

•the drive receives the appropriate fault LED command from the host

The Fault LED Out signal is designed to pull down the cathode of an LED. The anode is attached to the proper +5 volt supply through an appropriate current-limiting resistor. The LED and the current-limiting resistor are external to the drive.

9.5.8Active LED Out

The Active LED Out signal is driven by the drive as indicated in Table 21.

Table 21: Active LED Out conditions

Normal command activity

LED status

 

 

 

 

Spun down and no activity

Slow blink (20% on and 80% off a 2 sec cycle)

 

 

Spun down and activity (command executing)

On

 

 

Spun up and no activity

On

 

 

Spun up and activity (command executing)

Off

 

 

Spinning up or down

Blinks steadily (50% on and 50% off)

 

 

Format in progress, each cylinder change

Toggles on/off

 

 

Page 65 Page 67
Image 66
Page 65 Page 67
Contents Page Page Page Page Revision status summary sheet Revision Date Writer/Engineer Sheets AffectedPage Contents Seagate Technology support services Defect and error managementInstallation Interface requirementsList of Figures Cheetah 10K.6 FC Product Manual, Rev. B ViiPage Scope Cheetah 10K.6 FC family disc driveCheetah 10K.6 FC Product Manual, Rev. B Applicable standards and reference documentation Taiwanese Bsmi Australian C-TickKorean MIC Reference documentsGeneral description Cheetah 10K.6 FC disc drivePerformance Standard featuresMedia description ReliabilityUser-installed accessories Factory-installed accessoriesFactory-installed options Unformatted and formatted capacitiesCheetah 10K.6 FC Product Manual, Rev. B Seek performance characteristics Access time Performance characteristicsInternal drive characteristics Format command execution time in minutesPrefetch/multi-segmented cache control General performance characteristicsStart/stop time Cache operationCaching write data Prefetch operation Reliability specifications Service life Reliability and servicePreventive maintenance Service philosophy7 S.M.A.R.T Controlling S.M.A.R.TPerformance impact Determining rate MillisecondsReporting control Predictive failuresInvoking DST State of the drive prior to testingImplementation Short and extended testsAbort Product warrantyLog page entries ShippingDC power requirements Physical/electrical specificationsAC power requirements General DC power requirement notesCurrent profiles Power sequencingConducted noise immunity +5V +12VTypical ST373307FC drive +12V current profile Typical ST3146807FC drive +5V current profile Typical ST373307FC drive +5V current profile Power dissipation ST3146807FC ST373307FCTemperature Cheetah 10K.6 FC Product Manual, Rev. B ST336607FCShock and vibration Relative humidityEffective altitude sea level ShockPackage size Packaged/product weight Drop height Recommended mounting Air cleanliness Cheetah 10K.6 FC Product Manual, Rev. B VibrationAcoustics Mechanical specifications Mounting configuration dimensionsDefect and error management Drive internal defects/errorsDrive error recovery procedures Read and write retry count maximum recovery times Read retry Maximum recovery time per Write retryFC-AL system errors Maximum recovery time perInstallation Drive ID/option selectionLED connections Drive orientation 1 J6 connector requirementsDrive Front CoolingDrive mounting Air flowGrounding Interface requirements FC-AL featuresFibre Channel link service frames Fibre Channel task management functionsFibre Channel port login NPort login Plogi payload BytesNPort Login Accept ACC payload Bytes Fibre Channel Process LoginFibre Channel Process Login Accept Process Login Plri payloadFibre Channel fabric login Fabric Login Flogi payload BytesFabric Login Accept ACC payload Bytes Accept or NPort Login when sending frames to an initiatorFC-AL options supported Fibre Channel Arbitrated Loop optionsDual port support Option SupportedSupported commands Command code Command name Supported commands Command code Supported Command nameRead descriptor mode Cheetah 10K.6 FC Product Manual, Rev. B Cheetah 10K.6 FC inquiry data Mode Sense dataCheetah 10K.6 FC Product Manual, Rev. B Inquiry data Bytes Data hexCheetah 10K.6 FC Product Manual, Rev. B DEF DEF CHG Cheetah 10K.6 FC Product Manual, Rev. B Supported Feature or condition Miscellaneous operating features and conditionsMiscellaneous features Miscellaneous status Physical characteristics Physical descriptionConnector requirements Part description Positions Part number FeaturesPin Signal name Signal type Pin descriptionsFC-SCA pin descriptions FC-AL transmitters and receivers PowerFault LED Out Active LED OutEnable port bypass signals Motor start controls11 SEL6 through SEL0 ID lines Parallel Enclosure Services Interface ESI Setting Setting Hex DecArbitrated loop physical address Alpa values LED driver signals Signal characteristicsTTL input characteristics Device control codesTransmit eye diagram Differential Pecl inputEye diagram data values Link rate GHzPresales Support Seagate Technology support services Online ServicesAutomated Services Technical SupportCustomer Service CSO USA/Canada/Latin America Support ServicesEuropean Support Services Africa/Middle East Support Services Asia/Pacific Support ServicesCall Center Toll-free Direct dial Cheetah 10K.6 FC Product Manual, Rev. B Index FC-AL Cheetah 10K.6 FC Product Manual, Rev. B Plogi Cheetah 10K.6 FC Product Manual, Rev. B Cheetah 10K.6 FC Product Manual, Rev. B
Related manuals
Manual 2 pages 5.2 Kb
Top Page Image Contents