Yamaha YSP-1000 owner manual Error messages for Auto Setup, Before the Auto Setup procedure starts

Page 37

AUTO SETUP

■Error messages for AUTO SETUP

Before the AUTO SETUP procedure starts

Error message

Cause

Remedy

See

page

 

 

 

 

 

 

 

ERROR E-2

The optimizer microphone is not

Connect the optimizer microphone to

29

No MIC Detected. Please check

connected to this unit.

this unit.

 

MIC connection and re-try.

 

 

 

 

 

 

 

While the AUTO SETUP procedure is in progress-

 

 

 

 

 

 

Error message

Cause

Remedy

See

page

 

 

 

 

 

 

 

ERROR E-1

There is too much unwanted noise in

Make sure that your listening room is as

—

Please test in more quiet

your listening room.

quiet as possible. You may want to

 

environment.

 

choose certain hours during the day

 

 

 

when there is not much noise coming

 

 

 

from outside.

 

 

 

 

 

ERROR E-2

The optimizer microphone was

Make sure that the optimizer microphone

29

No MIC detected. Please check

disconnected while the AUTO SETUP

is firmly connected to this unit.

 

MIC connection and re-try.

procedure was in progress.

 

 

 

 

 

 

ERROR E-3

Some other operations were performed

Do not perform any other operations

—

Unexpected control is detected.

on this unit while the AUTO SETUP

while the AUTO SETUP procedure is in

 

Please re-try.

procedure was in progress.

progress.

 

 

 

 

 

ERROR E-4

The optimizer microphone is not placed

Make sure that the optimizer microphone

29

Please check MIC position. MIC

in front of this unit.

is installed in front of this unit.

 

should be set in front of YSP.

 

 

 

 

 

 

 

ERROR E-5

The optimizer microphone is not placed

Make sure that the optimizer microphone

29

Please check MIC position. MIC

in the right distance from this unit.

is installed more than 2 m from the front

 

should be set above 2m/6.5ft.

 

of this unit and within 1 m from the

 

 

 

center height of this unit.

 

 

 

 

 

ERROR E-6

The optimizer microphone cannot collect

Make sure that the optimizer microphone

29

Volume level is smaller than

the sound produced by this unit because

is firmly connected to this unit and

 

expected. Please check MIC

the sound output level is too low.

placed in a proper location. If the

 

position/connection and re-try.

 

problem persists, contact the nearest

 

 

 

YAMAHA service center for assistance.

 

 

 

 

 

ERROR E-7

An internal system error occurred.

Repeat the AUTO SETUP procedure.

—

Unexpected Error Happened.

 

 

 

Please re-try.

 

 

 

 

 

 

 

SETUP

English

35

Page 36 Page 38
Image 37
Page 36 Page 38
Contents YSP-1000 For U.K. Customers Contents Overview Auto Setup FeaturesInstall this unit in your listening room Using this ManualRun Auto Setup Connect this unit to your TV and other external componentsSupplied Accessories Front panel Controls and FunctionsInput STANDBY/ONFront panel display Rear panel Remote control Macro VOL ModeInputmode SleepBefore installing this unit InstallationInstalling this unit Parallel installationExample Installation examplesUsing a stand Using a metal wall bracketUsing a TV stand Using a rackFasteners Affixing this unitFor audio input For video input ConnectionsFor video output Audio connection Video connectionAudio connections Video connections Connecting a TVCables used for audio connections Cables used for video connectionsDVD player/recorder Connecting a DVD player/recorderAudio connections Connecting a VCRAnalog audio Video Output Digital satellite tuner or a cable TV tuner Connecting a digital satellite tuner or a cable TV tunerDigital airwave tuner Connecting a digital airwave tunerCables used for connections Connecting other external componentsCD player, etc Optical digital Output Subwoofer Monaural Input Rear panel of this unit Connecting a subwooferAffixing the optical cable Connecting the power supply cableAbout the RS-232C/REMOTE IN/IR-OUT terminals Operation range of the remote control Installing batteries in the remote controlClose the battery cover Getting StartedVOL Mode Surround Menu Return Using the remote control Turning on the powerDisplaying the OSD Using SET MenuOther buttons that display the OSD OSD screen exampleRun Basic Setup Flow chart of SET MenuRun Manual Setup Look for a remedyFlow chart of Auto Setup Auto SetupSide view Optimizer microphone Installing the optimizer microphoneExample of using the supplied cardboard microphone stand Example of using a tripodAssembling the supplied cardboard Microphone stand Center line TripodUsing Auto Setup SET Menu Auto Setup PreparationBeam OPT+SOUND Optimz Installing Installing Press Mounting Mounting To select and configureEach parameter and then press Enter Reflecting ReflectingAuto Beam Optimization Preparation PreparationAcoustic Optimization Show ResultBefore the Auto Setup procedure starts Error messages for Auto SetupWhile the Auto Setup procedure is in progress Memory Using the System Memory2MEMORY Save EnterPress Enter again Loading settingsPress Menu to exit Press / to select Load and then press 6 Press Enter again Memory 1MEMORY LoadPlayback Remote control operationsSelecting the input source Front panel operationsPlaying back sources Muting the sound Press Mute on the remote control to mute the soundFlashes Lights upBeam Mode Stereo plus 3 beam mode Beam modePress 5BEAM on the remote control to select the 5 beam mode Press Stereo on the remote control to select the stereo mode Press 3BEAM on the remote control to select the 3 beam modeTarget mode Status Indicator Decoder indicatorsEnjoying Surround Sound Surround modes and recommended sourcesEnjoying 2-channel sources in surround sound Press TV on the remote control Remote control to select a surround modePress Surround repeatedly or press Surround and then press / onPress YSP on the remote control to switch to Adjusting surround modePress Surround on the remote control Press / to configure the parameterWhen DTS Neo6 Music is selected When Dolby Pro Logic II Music is selectedWhat is a sound field? Using Sound Field ProgramsElements of a sound field Early reflectionsSound field program descriptions Music sound field programs Sports sound field program Movie sound field programsPress / on the remote control Adjusting Cinema DSP levelsNightcinema Nightmusic TV Equal VOL Night OFF Using the Volume ModeEffect.LvlMIN Effect.LvlMID Effect.LvlMAX Press on the remote control Using TruBassUsing Trubass Setting the sleep timer Using the Sleep TimerUnit to confirm the setting for the sleep timer Flashes Lights upDisappears Canceling the sleep timerBasic Setup SET Menu Basic SetupPress / to select Basic Setup and then press Enter Displaying the SET Menu screenRoom Type ? Basic SetupRoom Type Room type If Square is selected for Room Type Installed Position Installed position of this unitIf Rectangle is selected for Room Type Left CenterRoom Size Room size Room Size ?Small Small MID Medium Large Large Small Setup OK Confirming settingsLarge Press Menu to complete the Basic Setup procedure Setup OK?Press / to select YES or no and then press Enter Sound Menu Manual SetupBeam Menu Input MenuManual Setup Using Manual SetupPress / to select Manual Setup and then press Enter Press / / / and Enter to configure each parameterSetting parameters Asetting Parameter 1/3Installed Position Installed position of this unit Beam MenuBeam Adjustment Beam adjustment Bbeam AdjustmentInstalled Height Installed height of this unit Vertical Angle Vertical angle Horizontal Angle Horizontal angleBeam Travel Length Beam travel length Treble Gain Treble gain Focal Length Focal lengthSound Menu Cimage LocationAtone Control Image Location Image locationCsubwoofer SET Bbeam LevelBeam Level Beam level Subwoofer SET Subwoofer setDmute Level Eaudio DelayFroom EQ Input Menu Binput ModeAinput Assignment 1/4 Ainput Assignment 2/4Dinput Rename Cinput TrimInput Trim Input trim Input Rename Input renameAdimmer SET Display MenuBosd SET Cunit SETPress Enter on the remote control Adjusting System ParametersRelease Input on the front panel Press / to adjust the maximum volume level Protecting the current settingsPress / to switch between Protect on Protect OFF Initializing the current settingsUsing the test tone Adjusting the audio balancePress / to switch between Preset Reset and Preset Cancel Press / to select the speaker you want to adjust Using the audio output being played BackPress / to adjust speaker volumes Press Test when you have completed all your adjustmentsOperation Advanced Auto Selecting the Input ModeDTS AnalogSetting remote control codes Remote Control FeaturesUsing the remote control Refer to Controlling other components onOperating your TV Controlling other componentsOperating your DVD player TV MutePress VCR to select VCR as the input source Operating your VCR playerSetting macros for the TV with the tuning capability Using the TV macroCanceling the macros Setting macros for the TV without the tuning capabilityOperating macros General TroubleshootingThere is noise interference when a DTS indicator does not light upSee Distorted or too little bass sound Too much bass soundRemote control Audio formats GlossaryAudio information Audio pin cable IndexAMP Section SpecificationsSpeaker Section GeneralDVD Player VCRSatellite Tuner Cable TV TunerWG11470
Top Page Image Contents