Vivotek PT71373GPP/ISMA manual Network settings, Network type, LAN & PPPoE

Page 33

VIVOTEK - A Leading Provider of Multimedia Communication Solutions

Network settings

Any changes made on this page will restart the system in order to validate the changes.

Make sure every field is entered correctly before clicking on .

Network type

“LAN” & “PPPoE”

The default type is LAN. Select PPPoE if using ADSL

"Get IP address automatically" & “Use fixed IP address”

The default status is “Get IP address automatically”. This can be tedious having to perform software installation whenever the Network Camera starts. Therefore, once the network settings, especially the IP address, have been entered correctly, select “Use fixed IP address” then the Network Camera will skip installation at the next boot. The Network Camera can automatically restart and operate normally after a power outage. Users can run IP installer to check the IP address assigned to the Network Camera if the IP address is forgotten or using the UPnP function provided by the Network Camera (MS Windows XP provides UPnP function at My Network Place). “IP address” This is necessary for network identification.

“Subnet mask” This is used to determine if the destination is in the same subnet. The default value is “255.255.255.0”.

“Default router” This is the gateway used to forward frames to destinations in a different subnet. Invalid router setting will fail the transmission to destinations in different subnet.

“Primary DNS” The primary domain name server that translates hostnames into IP addresses.

“Secondary DNS” Secondary domain name server that backups the Primary DNS. “Enable UPnP presentation” Enable the UPnP camera short cut

“Enable UPnP port forwarding” Enable uPnP port forwarding “PPPoE” If using the PPPoE interface , fill the following settings from ISP “User name” The login name of PPPoE account

“Password” The password of PPPoE account

- 32 -

www.vivotek.com

User's Manual - 32

Image 33

Contents Wireless Pan/Tilt Network Camera PT7137 Before You Use This Product Table of Contents FTP 886-2-82455282 886-2-82455532 Package Contents Hardware installation InstallationTo install in Ethernet Software Installation Page Page Page Initial Access to the Network Camera Check Network SettingsAdd Password to Prevent Unauthorized Access Authentication How to UseInstalling plug-in Main Screen with Camera View Primary user’s capabilityClient Settings ConfigurationStop Tilt speed Pan speedPan PatrolClient settings Page Url http//Network Camera/client.html Fine-tuning for Best Performance Administrator’s capabilityFor Viewing by Mobile Phone Somewhere Between Real-time and Clear Images Opening accounts for new users Protect Network Camera by passwordsBuild a security application Software revision upgrade Definitions in Configuration System parameters Security settings Network type Network settingsLAN & PPPoE Get IP address automatically & Use fixed IP addressRtsp Streaming HttpPage Url http//Network Camera/setup/network.html Wlan Configuration Tkip AES Url http//Network Camera/setup/wireless.html Ddns Access List Audio and Video Video SettingsGeneral Video orientationAudio settings Image Settings Camera control area Camera ControlPreset function area FTP Email & FTPThis value from 1025 to Motion detection Snapshot Application settingsSnapshot file name prefix Weekly scheduleSend out the snapshot while motion detection Sequential operationPage Video Clip Page System log Viewing system parameters Calibrate MaintenanceTroubleshooting Reset and restoreStatus LED URL commands of the Network Camera Get server parameter valuesMethod GET/POST Return Set server parameter valuesWhere parameter pair is parameter=value\r\n Skip to invoke default server WirelessNetwork CameraAvailable parameters on the server Yyyy/mm/ddBlank Group Security255.255.255.0 192.168.0.99Than 40 characters Default Group Wireless restart554 555800000000 0000000000Group IPFilter 0.0176x144 for mobile 256640x480 For ComputerFor 60Hz only 512000AAC4 for computer Gamr for mobile12200 Tilt speed To take effect Script.vssx Camera ControlIP address 514Syntax RecallApplication page CGI command Page Maxsize PrefixappindexAccount management Capture single snapshotPrivilege=conf System logsConfiguration file Post data Upgrade firmwareNetworking Technical specificationsTechnology License Notice Liability Electromagnetic Compatibility EMC