Digimerge DHU104 Appendix 4 Connecting Motion/Alarm Devices, Installing a Sensor, Not Included

Page 60

Appendix 4: Connecting Motion/Alarm Devices

Appendix 4: Connecting Motion/Alarm Devices

Motion detection and Alarm controls are enabled through the Menu system on the DVR. Additional motion sensor devices can be connected to the system (Motion Sensors, Door/ Window Sensors).

A motion detection or sensor unit can be used to send a signal to the DVR to begin camera viewing on the matching Video Channel (when enabled in the Menu):

•Example: A Window sensor unit has been installed on Alarm Block port #4. When this sensor is activated, the camera on DIN or BNC VIDEO port #4 will become active (if enabled in the MENU on the DVR)

Installing a Sensor

1.Connect the GROUND Cable to the GND port on the Alarm Block on the DVR

2.Connect the SIGNAL Cable to a numbered port.

To start ALARM RECORDING on the System, refer to the Menu Configuration section of this manual.

DVR

SENSOR

(Not Included)

	1-4 /5-8: Alarm input terminals		NO / NC: Alarm Output Terminals
	receive a signal from a device (i.e.	Ground	send a signal to another device
	Door or Window Sensor).	Ground	when an alarm input is detected.
	Door or Window Sensor).		when an alarm input is detected.

52

Image 60

Contents

Digital Video Surveillance Recorder Page Important Safeguards InstallationService General Precautions General PrecautionsDVR Features Table of Contents Event / Sensor Remote Control Hardware & Software Getting StartedFront Panel Rear Panel Remote Control 15. F3 N/AMouse Control Mouse ControlsDisplay Modes Initial Loading SequenceIndividual Camera Display Network Connectivity Indicator Covert Camera ModeNetwork Indicators Display ModesPTZ Pan/Tilt/Zoom & Focus Controls PTZ Control Screen Focus Control ScreenSystem Power Off System Log OffKey Lock System ShutoffActive Option Indicator Menu Navigation Controls & TipsMenu Navigation Controls Virtual Keyboard ControlPlayback and Navigation Controls Navigation / PlaybackRecord Setup Menu Select Record SetupRecording Menu Controls Panic RecordingSimple Recording Setting Advanced RecordingTime Interval Bar Selected Hour Changed Time Block Activation Manual Recording Search Mode Search By TimeSearch By Event System Setup Controls EnterSystem Setup Menu OSD Onscreen DisplayMonitor Camera Menu Camera TitleColor Setup PTZ SetupContrast, Tint and Color for individual PTZ Properties Motion SensorSelected Area is shaded in Grey Sound Menu SoundBuzzer Network Time Server Setup System MenuDATE/TIME User Management Controls forNetwork Mail Setup User Management ADD User ScreenSystem Management System Information ScreenFirmware Update Factory Defaults Control DeviceSystem Data Event / Sensor HDD EventAlarm Input Alarm OutputBuzzer Output Email Notification Disk Management Format Erases all Hard Drive dataArchiving Archiving MenuError Messages Archiving OptionsNetwork Connectivity Overview IP & MAC Address Finding Your External IP AddressSetting Up Your Ddns Account Navigate to http//ddns.digimerge.netUser Name Domain Name Password Router Port Forwarding TCP/IP PortRouter Computer Internet Internal NetworkDdns Setup Troubleshooting ProblemCheck Appendix 1 System Specifications General Specifications Appendix 1 System Specification cont’d Alarm Specifications Recording Specifications Network SpecificationsDVR Specifications LbsAppendix 2 Digimerge Client Software Requirements Appendix 3 Monitor Out DVRAppendix 4 Connecting Motion/Alarm Devices Installing a SensorNot Included GroundAppendix 5 Connecting a PTZ Camera Installing a PTZ RS-445 Type PTZ CameraPTZ Camera Not Included Appendix 6 Full Connectivity Diagram BNC CamerasAppendix 7 Replacing the Hard Drive Replacing the Hard DriveFormatting the New Hard Drive Appendix 8 Using the Storage Calculator Appendix 9 System Setup Tips Navigating within the System MenuMake Sure That the Date and Time are SET Prior to Recording Formatting the Hard Drive Camera Setup Backing up your System Configurations Appendix 10 Using Listen-In Audio Appendix 11 Playing Recorded Video Data Search By Event Setting An Individual Time Block Appendix 12 Recording ModesSetting Multiple Time Blocks Appendix 13 Setting Up Remote Viewing What do I need?IP & MAC Address Setting Up Your Ddns Account User Name Domain Name Password Network Router Port Forwarding Ddns Setup Digimerge NetViewer Software Connection Manager Adding a GroupAdding a Site Individual Unit Configuration Camera Assign Set each camera to a portionDigimerge NetViewer Software Remote Connection Limited Warranty Canada Page IT’S ALL on the WEB