JVC VN-C655 manual Connection of Conveter Unit, Connect the camera to AC 24, Connecting Cables

Page 18

Preparation (Step 1 Connection/Installation)

1-1 Connecting Cables (Continued)

6. Connection of Conveter Unit

Press	Power cable

2. 5mm Press

1. Connector

Press

3.

to AC 24V

4.

Connect the camera to AC 24 V.

1. Disconnect the connector from the sup- plied Converter Unit.

It can be disconnected by pressing both ends as shown in the left figure.

2. Mount the power cable to the connector. Strip the cover of the power cable (about 5 mm), while pressing down the arrow portion using a flat screwdriver, insert it into the con- nector.

3. Mount the connector.

4. Connect the supplied Converter Unit to the DC 18V input terminal on the terminal stand.

When a 2-conductor VVF (Vinyl-insulated vinyl-sheath cable) is used, the maximum connection length is as shown below. (These are merely the standard reference values.)

Maximum cable length	70 m	180 m	280 m	480 m
Wire diameter (mm)	1.0 or more	1.6 or more	2.0 or more	2.6 or more

Caution

¥Connect with the appropriate power-supply voltage. The rated voltage for VN-C655 (Converter Unit) is AC 24 V, 50 Hz/60 Hz and shall be Class 2.

If a voltage exceeding the rating is supplied, malfunction, or in the worst case, fuming or fire, may be caused.

¥Installation shall be performed by qualified personnel according to regulations of individual regions.

Notes

Connecting multiple VN-C655 Cameras

In a system where more than 1 VN-C655 is used, turn on the power for a VN-C655 first, followed by setting the camera until "2-3 Setting IP Address for this Camera Using the 'VN-C655U Setup Tool' " is completed. Upon doing so, turn on a second camera and perform setting in the same way. Perform the same procedure for subsequent cameras.

¥Default IP address setting for all VN-C655 cameras is 198.168.0.2. When the power for multiple cameras are turned on at one time under a single LAN environment, therefore, proper access may not be established due to IP address redundancy. Do not turn on the power of more than 1 camera at the same time.

¥When IP address redundancy occurs, ensure that only one VN-C655 exists under a single LAN environment, and wait for some time (at least 10 minutes). In some cases, the power for all network devices under the same LAN environment may have to be turned off and on again to enable access to VN-C655.

18

Image 18

Contents VN-C655 Safety Precautions Information for USAImportant Safeguards Contents Introduction Preparation SettingsOperating Using a Web Browser Setting Using the V.Networks ControllerOperating Using the V.Networks Controller OperationCharacteristics Operating PrecautionsIntroduction Consumable Parts Zooming operationOperating Precautions Items Included Latest UpdatesPC Specifications Operating EnvironmentAlarm I/OAlarm Input/Output Terminals Pin No Signal NameName and Function of Parts Camera Terminal Female @ Dome Cover Camera Terminal Male Drop Prevention WireCeiling MountCamera Drop Prevention Hook # LensNetwork Connection Connection ExamplesLAN Connection Peer-to-Peer ConnectionPreparation Procedure Set the camera in the following procedureMaking the hole Connecting CablesLan cable Alarm signal cable Coaxial cable Converter Unit Connect the cablesConnection to Alarm Input/Output Terminal Cable SpecificationsInput Requirements Preparation Connection/Installation Connection of LAN CablesOutput Requirements Connecting a 5C-2V or 3C-2V coaxial cable Connection of Coaxial CablesConnecting multiple VN-C655 Cameras Connecting CablesDisconnect the connector from the sup- plied Converter Unit Connection of Conveter UnitAttach safety wire to prevent camera from falling down Attachment of Ceiling MountCeiling Mount Ceiling structure. If the ceiling structure is Installing the Camera Installing the Camera Turn the cameraFasten the locking screw Installing the V.Networks Controller Installing the SoftwareFollowing procedure from the CD-ROM supplied Installing the VN-C655U Setup ToolSetting PCs IP Address Windows XP Settings Network SettingsClick Select Internet Protocol TCP/IP and click Properties Click on the Local Area Connection Properties screenSetting PCs IP Address Windows Click Settings Network Settings Check settings Start up the V.Networks Controller.Other Settings Using the VN-C655U Setup Tool Authorization Level Allowed Access Following confirmation screen will be displayedOther Settings Using the VN-C655U Setup Tool 2. Multicast MulticastMulticast Address Search screen is displayed Start up the VN-C655U Setup ToolV.Networks Search screen is displayed Search result is displayedOperation when an alarm input is activated This section describes procedures for alarm settingAlarm Input Start up the VN-C655U Setup Tool and select AlarmPage Alarm Output Alarm 1/AlarmDetect Mode Go to a presetRelay Alarm Alarm 1/Alarm Message PacketAlarm FTP AvailablePreset Position Position Return ModeMotion Detection Alarm Output Setting the Trigger Recording screen Setting the Frame Rate screenExample Setting the Advance screen Recording timeRecording files Start up the VN-C655U Setup Tool and select Private Mask When all the settings have been completed, click to endFixed area Free areaPerform area setting Other Settings Using the VN-C655U Setup Tool 7. Web Displaying still images uploaded to the /user folderOther Settings Using the VN-C655U Setup Tool 8. FTP Server Start up the VN-C655U Setup Tool and select FTP ServerTrigger FTP ¥ Alarm FTPContinuous FTP ¥ Rec FileTransfer error PasswordError recovery Connection error Alarm FTP Upload SettingMode Black and White TimeOne Push AF Auto LevelLight Start up the VN-C655U Setup Tool and select Time When NTP is usedStart up the VN-C655U Setup Tool and select Memory Info NormalHigh Speed Connect to VN-C655 Settings Setting Using the V.Networks Controller Starting Up V.Networks ControllerFeatures that Allow Setting Using the V.Networks Controller 4Setting Quality Settings Setting Using the V.Networks ControllerFeatures that Allow Setting Using the V.Networks Controller Frame rateMotion Detection Standby Select File and Motion Detection Standby Select a cameraOperations Setting Using the V.Networks Controller Select View Specify Image Size and Upside Down settingsImage Size and Inversion Image Quality Setting Image Quality Setting Image Quality Setting Large Peak value Auto Black ControlAverage Peak Set valueExDR Mode Sense UpExDR Level Setting values -5 to SharpnessImage Quality Setting Lens Select Setting and Frame rate Set the Frame Rate Frame RatePreset Position Setting Select Setting and Position MemoryAlarm Setting When setting is complete, clickAlarm Setting Pan/Tilt Setting Auto Pan Setting Select Setting and Auto Pan SettingPerform setting Close the windowAuto Patrol Setting Select Setting and Auto Patrol SettingAuto Patrol No Auto Trace Setting Select Setting and Auto Trace SettingStart to memorize operation Close the window Select Setting and Time Stamp Perform setting Time StampSelect Setting and Property Perform setting When alteration is complete, clickChanging Registered Information Buttons for position moving Snap ShotReduced Screen # Pan/Tilt/Zoom Position Indicator Pan/Tilt button@ Size Click the REC button Operations Operation Using the V.Networks ControllerRecord/Stop Click the Stop buttonPlayback Playback Click Playback screen is displayed Record/Playback Time Image Size Data Size Per Image Approximate Recording TimeSnap screen will be displayed SnapshotClick the Snap Shot button Save As screen is displayedLAN Environment Web Page ImagesAccess Authorization Level Operations Operating Using a Web BrowserAuthentication of Access Authorization Starting Up the Web Browser Start up the web browserTop page will be displayed Setting Using the Web Browser Display the TopTop Settings page will be displayed Setting Using the Web Browser 1. Other Settings Other settingsAdministrator Level Description of Items in Other Settings MeaningDefault Gateway DefaultSetting Using the Web Browser 1. Other Settings Http port number, check using the setup tool supplied# NTP Settings Setting Using the Web Browser 2. Control Setting Using the Web Browser 3.Image Setting Operations Setting Using the Web Browser@ Manual Focus Level # Iris ModeAGC $ White BalanceSetting Using the Web Browser 3.Image Setting 1Low, 2 to 7, 8Fast Setting Using the Web Browser 4. PAN/TILT SettingPAN/TILT Speed Auto Flip According to ZOOM, speed of operation isSetting Using the Web Browser 5. Position Memory Setting Image Settings ScreenSetting Using the Web Browser 6. View Setting ResolutionSetting Using the Web Browser 7. Alarm Setting 100 Alarm Alarm Out Other Triggers Setting Using the Web Browser 8. FTP Setting 102Error Recovery Still image FTP, Same as Alarm FTP JpgSpecify a recovery action when errors related to FTP occur On connect error Retry foreverSetting Using the Web Browser 9. Auto Pan Setting Duration Setting Using the Web Browser 10. Auto Patrol SettingPosition Number 105For setting image quality Setting Using the Web Browser 11. Auto Trace SettingRecord Start Confirmation Screen Image Setting Screen 106Setting Using the Web Browser 12. Black & White Setting Setting Using the Web Browser 13. Schedule Setting107 Setting Using the Web Browser 14. Private Mask Setting Mask Position and Size Controller 108Viewing Still Images 109Viewing Live Images 110Image Link Displaying a still image111 Troubleshooting Symptom Causes/Remedial Actions112 113 Specifications External Dimensions Unit mm inches Ceiling Mount Hole Unit mm inchesVN-C655 Dome Type Network Camera