EN 69
33. | Coloured bright spots appear | 33. | • The LCD monitor and the | 33. |
|
|
|
| all over the LCD monitor or the |
| viewfinder are made with |
|
|
|
|
| viewfinder. |
|
|
|
|
| |
|
|
| However, black spots or |
|
|
|
|
|
|
| bright spots of light (red, |
|
|
|
|
|
|
| green or blue) may appear |
| — |
|
|
|
|
| constantly on the LCD |
|
|
| |
|
|
| monitor or the viewfinder. |
|
|
|
|
|
|
| These spots are not recorded |
|
|
|
|
|
|
| on the tape. This is not due to |
|
|
|
|
|
|
| any defect of the unit. |
|
|
|
|
|
|
| (Effective dots: more than |
|
|
|
|
|
|
| 99.99 %) |
|
|
|
|
|
|
|
|
|
|
|
|
34. | The indicators and the image | 34. | • This may occur when the | 34. |
|
|
|
| colour on the LCD monitor are |
| surface or the edge of the |
| — |
|
|
| not clear. |
| LCD monitor is pressed. |
|
|
|
|
|
|
|
|
|
|
|
|
35. | The cassette will not load | 35. | • The battery’s charge is low. | 35. | • Install a fully charged battery. |
|
|
| properly. |
|
|
| ( pg. 10, 11) |
|
|
|
|
|
|
|
|
|
|
36. | The memory card cannot be | 36. | — | 36. | • Push in the memory card a |
|
|
| removed from the camcorder. |
|
| few more times. ( pg. 16) |
|
| |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
37. | Picture does not appear on the | 37. | • The viewfinder is pulled out | 37. | • Push the viewfinder back in |
|
|
| LCD monitor. |
| and “PRIORITY” is set to |
| or set “PRIORITY” to “LCD”. |
|
|
|
|
| “FINDER”. |
| ( pg. 12, 31, 38) |
|
|
|
|
| • The LCD monitor’s brightness |
| • Adjust the brightness of the |
|
|
|
|
| setting is too dark. |
| LCD monitor. ( pg. 13) |
|
|
|
|
|
|
| • If the monitor is tilted |
|
|
|
|
|
|
| upward 180 degrees, open |
|
|
|
|
|
|
| the monitor fully. ( pg. 12) |
|
|
|
|
|
|
|
|
|
|
38. | Images on the LCD monitor | 38. | • The speaker volume is too | 38. | • Turn the speaker volume |
|
|
| are jittery. |
| great. |
| down. ( pg. 20) |
|
|
|
|
|
|
|
|
|
|
39. | The LCD monitor, the | 39. |
| 39. | • Wipe them gently with soft |
|
|
| viewfinder and the lens have |
| — |
| cloth. Wiping strongly can |
|
|
| become dirty (ex. fingerprints). |
|
|
| cause damage. ( pg. 73) |
|
|
|
|
|
|
|
|
|
|
40. | Time code does not appear. | 40. | •“TIME CODE” is set to | 40. | • Set “TIME CODE” to “ON”. |
|
|
|
|
| “OFF”. |
| ( pg. 31, 38, 41) |
|
|
|
|
|
|
|
| REFERENCES | |
42. | An error indication (E03 or | 42. | • A malfunction of some kind | 42. | • pg. 81. | ||
41. | An error indication (E01, E02 | 41. | • A malfunction of some kind | 41. | • pg. 81. |
|
|
| or E06) appears. |
| has occurred. In this case the |
|
|
|
|
|
|
| camcorder’s functions |
|
|
|
|
|
|
| become unusable. |
|
|
|
|
|
|
|
|
|
|
|
|
| E04) appears. |
| has occurred. In this case the |
|
|
|
|
|
|
|
|
|
| ||
|
|
| camcorder’s functions |
|
|
|
|
|
|
| become unusable. |
|
|
|
|
|
|
|
|
|
|
|
|
43. | The remote control does not | 43. | •“REMOTE” is set to “OFF”. | 43. | • Set “REMOTE” to “ON”. |
|
|
| work. |
| • The remote control does not |
| ( pg. 31, 37) |
|
|
|
|
| point at the remote sensor. |
| • Point at the remote sensor. |
|
|
|
|
| • The remote control batteries |
| ( pg. 54) |
|
|
|
|
| are exhausted. |
| • Replace the batteries with |
|
|
|
|
|
|
| fresh ones. ( pg. 54) |
|
|
|
|
|
|
|
|
|
|