JVC GR-DVX9 specifications EN63, To DV IN/OUT Core filter DV cable optional To DV OUT

Page 63
Make sure all units are turned off. Connect the camcorder to a video unit equipped with a DV output connector using a DV cable as shown in the illustration.

POWER Switch

Lock Button

Open the connector cover.

To DV IN/OUT

Core filter

DV cable (optional)

Core filter

To DV OUT

Video unit equipped with DV connector

EN63

Dubbing From A Video Unit Equipped With A DV Connector (Digital Dubbing)

[To use this camcorder as a recorder: Only for GR-DVX10 owners]

NOTE:

Before the following steps, make sure that “AV/S-VIDEO” is set to “OUT” in the Menu Screen (  pg. 41).

1

2 Set “REC MODE” to “SP” or “LP” in the Menu Screen depending on your preference ( pg. 11).

3 Set this camcorder’s POWER Switch to “” while pressing down the Lock Button located on the switch. Turn on the video unit’s power and insert the appropriate cassettes in the camcorder and the video unit.

4 Press START/STOP on the camcorder to engage the Record-Pause mode.

“DV. IN” appears on the screen.

5 Engage the video unit’s Play mode, then engage the Still Playback mode when you have found a spot just before the edit-in point.

6 Press START/STOP on the camcorder to engage the

Record mode. “ DV. IN ” appears on the screen. Engage the video unit’s Play mode.

7 To stop dubbing, press START/STOP on the camcorder so that “DV. IN” reappears, then engage the video unit’s Stop mode.

8 Repeat steps 5 through 7 for additional editing.

NOTES:

It is recommended to use the AC Power Adapter/ Charger as the power supply instead of the battery pack ( pg. 7).

If the remote control is used when both the player and recorder are JVC video units, both units will perform the same operation. To prevent this from happening, press the buttons on both units.

For Digital Dubbing, this camcorder can be connected only to one device at a time.

If a blank portion or disturbed image is played back on the player during dubbing, the dubbing may stop so that an unusual image is not dubbed.

Even though the DV cable is connected correctly, sometimes the image may not appear in step 5. If this occurs, turn off the power and make connections again.

When using a DV cable, be sure to use the optional JVC VC-VDV204U DV cable.

Digital Dubbing is performed in the sound mode recorded on the original tape, regardless of the current “SOUND MODE” setting (  pg. 27).

During Digital Dubbing, no signals are output from the video or audio connectors.

Image 63
Contents GR-DVX10 GR-DVX9 It is recommended that you Dear CustomerSome DO’S and DON’TS on the Safe USE of Equipment DC Cord Remote Control Unit RM-V716U Core Filter xCleaning Cloth RCA plug cable Cable AdapterWind once How To Attach Core FiltersRelease the stoppers on both ends of the Core Filter StopperBenefits Of Lithium-Ion Batteries PowerCharging the Battery Pack Lithium-ion is vulnerable in colder temperaturesWhile sliding down BATT. RELEASE, detach it Using the Battery PackUsing AC Power To Detach The Battery PackTripod Mounting Grip AdjustmentViewfinder Adjustment Dioptre Adjustment ControlPower Switch Power Lamp Lock Button Operation Menu Wheel Date/Time SettingsBuilt-in Clock’s Rechargeable Lithium Battery Set the Operation Switch to and set the PowerCassette holder cover OPEN/EJECT Switch Erase protection tab10EN Loading/Unloading a CassetteMenu Screen Sub Menu Recording Mode SettingEN11 Display12EN Loading a MultiMediaCardTo Unload a MultiMediaCard EN13 Picture Quality/Size Mode SettingSet the Power Switch to While pressing Mode Dial to14EN Operation ModePower Switch Position Operation Switch Position ManualFunction Mode Dial PositionProgressive Mode EN15To Stop Recording To Adjust The Brightness Of The Display16EN Press START/STOPSelf-Recording EN17Journalistic Shooting SELF-RECORDINGSnapshot Recording Snapshot Mode Selection18EN Snapshot For Video RecordingTo Remove The Shutter Sound Basic Shooting SnapshotEN19 To Delete Unwanted Still ImagesZoom Out Slide the Power Zoom Lever towards T20EN ZoomWhen a blank portion is recorded on a tape EN21Proper recording To End Progressive Mode Recording Progressive Mode RecordingFrame Scan a Scan B Description of Progressive Scan CCDEN23 Regular shooting of moving imagesFully-pressed Position Dual ShootingFocus Button Still imageTo obtain correct focus Feature Auto FocusFeature Manual Focus EN25Menu Screen Power Switch Lock Button Operation Switch Menu WheelSee pg Go to stepEN27 Menu Screen ExplanationsAutomatic demonstration will not take place Refer to Self-Timer  pgDemonstration will resume After viewing demo, set to OFFEN29 If Auto Is Selected Snapshot FlashMenu Wheel Display Flash Brightness AdjustmentPower Switch Lock Button Operation Switch EN31Self-Timer Mode Dial to Video Second RecordingEN33 To Deactivate The Selected Effect Fade/Wipe EffectsFADE/WIPE Selection Picture Wipe or Dissolve SelectionEN35 Fader And Wipe MenuMenu Effect Programme AE With Special Effects To Deactivate The Selected ModeEN37 Sound Effect Mode SelectionTo cancel recording the sound effect midway Digital Sound EffectsIris Lock Exposure ControlTo Return To Automatic White Balance White Balance AdjustmentManual White Balance Operation EN39Rewind Button To Control The Speaker VolumeAvailable only with the remote control provided  pg Power Zoom Lever VOL Menu Wheel Speaker Lock ButtonEN41 42EN Playback SoundDisplay Video Menu appears To cancel Blank Search midwayBlank Search EN43To view video clips stored in a MultiMediaCard To cancel E-Mail Clip Recording44EN Mail Clip RecordingNumbered, then stored in numerical order Normal PlaybackAuto Playback Images shot with the camcorder are automaticallyDirectory Protect icon Power Switch Lock Button Menu WheelIndex Screen Type of fileIf you press Index three times Index PlaybackEN47 If you press Index twiceTo Remove Protection 48ENProtecting Files To Protect a FileTo Select a File by Browsing Files Stored in Memory Power Switch Lock ButtonDeleting Files EN49You can initialise a MultiMediaCard anytime Power Switch Menu Wheel Display50EN Initialising a MultiMediaCardPress Print Frame Superimposing a Print FrameEN51 To Make The Print Frame DisappearLock Button Delete Index Screen Deletion Confirmation Set the Power Switch to52EN Print Frame DeletionTo Delete ALL Print Frames To Reset The Setting 54ENTo Print ALL Still Images ONE Print for Each Perform steps 1 through 4 on pg To Reset The No. Of PrintsEN55 To Print by Selecting Still Images and NO. of PrintsTighten the screw 56ENDocking Station with the stud hole CamcorderIf using a VCR . . . go to step If not . . . go to step EN57Make sure all units are turned off Connection To a Personal Computer 58ENCore filter Digital Printer Connection To a Video Unit Equipped With a DV ConnectorEN59 With a DV inputFor GR-DVX10 owners only 60ENDubbing To a VCR To use this camcorder as a playerEN61 Dubbing From a VCR62EN To DV OUT Core filter DV cable optionalPlay Stop To DV IN/OUT Core filter DV cable optional To DV OUT EN63Indicator disappears when dubbing is complete 64ENDubbing Images Stored In a MultiMediaCard To a Tape Menu Wheel Power Switch Lock Button Dubbing Images Recorded On a Tape To a MultiMediaCardEN65 Remote sensor Installing The Batteries66EN TabFunctions Buttons EN6768EN Feature Slow-Motion PlaybackFeature Frame-By-Frame Playback Feature Playback ZoomFeature Playback Special Effects EN69Effect Select Menu You are now ready to try Random Assemble Editing 70ENSET REMOTE/VCR Code VCR Recording deckMake Connections EN71Editing Menu 72ENSelect Scenes ProgrammeAutomatic Editing to VCR EN73Tvvcr Recording deck 74ENFor More Accurate Editing Diagnosing VCR/CAMCORDER TimingAdjustment of VCR/CAMCORDER Timing EN75Recording deck To hear the dubbed sound during playback Set 12BIT Mode to Sound 2 or MIX Menu Screen  pg76EN Audio DubbingEN77 Audio Dubbing Using Digital Sound EffectsAfter Use Cleaning The CamcorderPush Here OPEN/EJECT Switch Hatch Lens blower 78ENCorrective Action Troubleshooting80EN TroubleshootingIs ending Dissolve before beginning EN81White Balance cannot be activated 82EN pg EN8384EN EN85 If 5 minutes elapse in the Record-Standby modePrinter Connector Multi Connector86EN EN87 Order of quality 88ENAppears while the tape is running Displays the Time CodeEN89 Displays the sound mode LCD Monitor/Viewfinder Indications During Video PlaybackLCD Monitor/Viewfinder Indications During D.S.C. Playback EN91 While the Power Switch is set to 92ENDeleted To avoid hazards To prevent damage and prolong service lifeEN93 Pack, be sure to read the Terminals following cautions94EN Serious malfunctioning EN95To protect the unit, do not About moisture condensation96EN Print Frame Deletion  pg EN9798EN EN99 EG/EK