Camco P.2 Series, P.9 Series, P.5 Series, P Series, P.0 Series, P.7 Series On/Off Switch, Mounting

Page 14

INSTALLATION

3.2. On/Off Switch

The On/Off Switch is a rocker-type switch. It is located on the right side of the front panel. To turn the amplifier on, push in on the upper part of the switch.This initiates start-up by activating the inrush current limiter. During power up the Clip and Signal LEDs from both channels will light up in red for a few seconds.To

3.3 Mounting

Use four screws and washers when mounting the amplifier to the front rack rails. For mobile use, the amplifier should also be secured using the 19” mounting elements on the rear panel.

3

P.12

turn the amplifier off, push in on the lower part of the switch.

Amplifier is switched on

Amplifier is switched off

NOTE: This switch does NOT disconnect the amplifier from mains.

Make sure the mains power socket or an alternative disconnect device is near by and easily accessible.

The switch initiates start-up by activating the current limiting function.

As soon as the power amplifier is connected to the mains power supply, a vol­ tage is supplied to both the line-filter and the fused input of the controllable rectifier. Disconnecting the amplifier from the main power supply can only be achieved by physically separating the amplifier from the mains by pulling the mains plug. The mains plug therefore has to be freely accessible. Disconnect the mains plug from the mains during a lightning storm or when the amplifier remains unused or unsupervised for a prolonged period of time. Alternatively, you can disconnect the amplifier via an external all-pole disconnection from the mains.

If a power cut occurs while the amplifier is switched on, it will restart automati­ cally once the power supply has been restored. All settings operation prior to the loss of power will be maintained.

USER MANUAL

TECTON POWER AMP SERIES

 

10 mm

88,9 mm 76,2 mm

7 mm

466 mm

442 mm

7 mm

 

330,7 mm

356,2 mm 347,2 mm

76,2 mm

10 mm

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Page Page Information for USE for Important Safety Instructions Important Safety InstructionsExplanation of Symbols / Safety Safety Manufacturers Address EC Declaration of ConformityManufacturers Name Declares that the product with the model nameContents Unpacking WelcomeWelcome to Camco Tecton is a Class-H power amplifier with a power output AmplifierFacilities Tecton The Front Tecton The RearFactory Settings Front panelInstallation Mains SupplyOn/Off Switch MountingGround Lift Mode IndicatorsCooling Mode Selector Wiring 1 E.U.I. and XLR ConnectionParallel-Mono Operation Stereo Operation, 2 Channel OperationMono-Bridge Operation One-channel mono bridged operation Operation Speakon ConnectionGain Selector Controls Volume ControlLimiter Switch Gain and Input SensitivityIndicators Output Current LEDs Signal LEDs multifunctionalSOA Protection Power Amp Protection Systems 4.3.1 Clip LimiterClip LEDs DC ProtectionMains Failure Detection Mains Protections Inrush Current LimitationMains Over Voltage Detection Fuse ProtectionE.U.I.2 Extended User Interface What Are The Possibilities Using The E.U.I.2?Options Troubleshooting Signal to Noise-Ratio SpecificationOutput Power Power Consumption @ 2301400 W @ 2 Ω 1100 W @ 2 Ω 670 W @ 2 Ω Output Connectors IndicatorsInput Connectors Dimensions WxHxDMeasurements Measurements of a typical performanceMeasurements of a typical performance of Tecton Ch1, Ch2 Measurements of a typical performance of Tecton Tecton 24.4 Measurements of a typical performance Tecton 14.2 Measurements of a typical performance Warranty Information Owner’s Information Expired WarrantyNature Of Problem Shipping AddressDecomissioning Maintenance InformationDECOMISSIONINGINFORMATION/12 Telephone Company InformationMailing Address Facsimile
Top Page Image Contents