JVC GY-HD250, GY-HD251 manual Loading/Unloading the Cassette, Cassette Loading, Mode, REC Save

Page 44

e_hd250.book Page 40 Tuesday, October 24, 2006 3:11 PM

PREPARATIONS FOR OPERATION

Loading/Unloading the Cassette

Cassette Loading

Use a videocassette tape marked MiniDV.

•To record, slide the switch on the back for use in prevent- ing accidental erasure to the “REC” side.

•Remove any the tape slack before loading.

1.Turn the POWER switch ON.

2.Slide the EJECT switch on the top panel of this device to the side.

The videocassette cover opens automatically and a vid- eocassette tape can be inserted.

3.Insert a videocassette tape into the videocassette holder. With the tape window facing out, move the switch on the back of the videocassette up and firmly push the center back of the videocassette straight in as far as it will go.

4.Carefully push the center (“Push here” sticker) of the vid- eocassette cover in the direction of the arrow as far as it will go to close it.

•After the cover is closed, it takes about 10 seconds until recording can begin or this device can enter STOP mode.

REC/SAVE

Tape window

switch

 

EJECT switch

Cassette holder

Unloading the Cassette

1.Turn the POWER switch to ON.

2.When this device is in shooting standby mode or stop mode, slide the EJECT switch to the side and wait until the videocassette cover opens completely.

•The LED next to the EJECT switch flashes.

A few seconds pass before the videocassette tape is ejected.

3.The LED turns off and the videocassette cover opens.

•Take out the videocassette tape.

4.Carefully push the center of the videocassette cover in the direction of the arrow as far as it will go to close it.

CAUTION

•When you close the videocassette cover, push it in firmly as far as it will go. If the videocassette cover is not closed properly, it becomes half-locked and this device cannot function.

If this happens, firmly push the videocassette cover in again as far as it will go to lock it.

•The videocassette cover does not open during recording even if you slide the EJECT switch.

•Do not leave the videocassette cover open for a long time.

Dust or dirt may enter the inside and cause damage.

•Do not touch the videocassette cover or interfere with the eject operation while ejecting is in progress. This will cause damage.

•When you close the videocassette cover, do not press the black area of the inner cover.

Videocassette cover

Inner cover

„If the power is on, the modes are as shown below.

MODE

REC/SAVE switch

REC

SAVE

 

Camera

Record-standby mode

STOP mode

 

 

REC INHIBIT is displayed

 

 

on the LCD monitor and in

 

 

the viewfinder.

 

 

 

VTR

STOP mode

 

40

Page 43 Page 45
Image 44
Page 43 Page 45
Contents For Customer Use Victor Company of Japan, Limited LST0440-001BImportant Safeguards Safety Precautions RemarqueSafety Precautions Cont’d Port Cable LengthBusiness users Other Countries outside the European Union Information for Users on Disposal Old EquipmentEuropean Union HD251CHE Main Features Contents Playback Mode Precautions for Proper Use Routine and Periodical Maintenance Precautions for Use of Head Cleaning TapeHead Cleaning Periodical MaintenanceBattery Pack to be Used Videocassette to be UsedCondensation occurs in the following cases Characteristic CCD Phe- nomenaCondensation Zoom Lens Th16 × 5.5BRMUFront Section Rear Section 1Back tally lamp2PHONES Earphone jack 3Shoulder belt hooksLCD Door Right Side Section BGAIN Sensitivity selector switch CWHT.BAL White balance switchASTATUS Status/Menu button GHDV/DV LEDLeft Side Section CGENLOCK/AUX in GENLOCK/AUX in switch DPBPR/TC PBPR/Time code switchEIEEE1394 IEEE1394 switch GGENLOCK/AUX in GENLOCK/AUX in terminal BNCTop Section DMONITOR Select Audio monitor selector switch FVTR VTR indicatorGFULL Auto Full auto shooting FAS switch LScrew holes for mounting accessoriesRecording and Image Out- put Formats Recording Composite RecordingIEEE1394 Indications on the LCD Monitor and in the View- finder Status ScreensStatus Screens in the Camera Mode Setting Status Contents of IndicationsContents Indications on the LCD Monitor and in the Viewfinder Cont’dIDX Endura battery Voltage/remaining capacity % UB FF EE DDTape time appears LCD/VF3/4 menu screen. X SeeCH-1O O O O O O O O O \ \ \ CH-2O O O O O O O O O \ \ \Filter OFF ND1 ND2Indication Indication Contents Status Screen in VTR Mode HDV/DV input signalVideo Format display DoorNDF Magnified Status Indications on LCD MonitorEXT Safety Zone Indication Camera mode only Alarm Message DisplayMenu Setting Screen Center Mark OFF Switching between the LCD Screen and Viewfinder DisplaySafety Zone Basic System HZ-ZS13BAttaching the Microphone Provided How to Attach the View- finderAttaching the Zoom Lens Inserting an SD Memory Card Taking out the SD memory cardInserting an SD Memory Card About SD Memory CardsAttaching the Tripod Base Provided only for U model AC Operation Charging the Built-in BatteryHow to charge the built-in battery Battery Operation Attaching the BatteryRemoving the Battery „GY-HD250UPrecautions for the Battery Opera- tion Remaining Battery Power DisplayOperating Time with Battery Pack Precautions for the Battery PackTurning the Power on Turning the Power onTurning the Power OFF Camera modeLoading/Unloading the Cassette Cassette LoadingUnloading the Cassette ModeSetting and Displaying the Date and Time Setting the Date and Time StyleDisplaying the Time and Date on the Screen Time code input entered the IEEE1394 connector SettingDisplaying Time Code Displayed Time Code/User’s BitPresetting and Recording of Time Code SettingDrop frame/Non-drop frame mode DropZero-resetting the Time Code or User’s Bit Data Presetting time code dataPresetting user’s bit data Presetting the Time Code from the LCD Screen Presetting User’s BitAborting Preset Operation OperationInternal About Time Code ModePlaying Back Time Code Slave unit GY-HD250U/GY-HD251E/GY-HD110U/GY- HD111E Settings and OperationsConnections Connection ExternalScreen Adjustment Viewfinder Adjustment Back Focus Adjustment White Balance Adjustment White Balance AdjustmentAdjustment procedure Error messagesWhite Shading Adjustment Setting the REC Item Setting the Video FormatSetting the Frame Rate Item ND Filter Camera SettingsScreen Size 43/169 Mode Selection Audio Input Signal Selec- tion Selecting the CH-2 channel input connectorSelecting the audio signal input Adjusting Audio during RecordingMonitoring Audio during Recording LOW/MIDDLE/HIGHBasic Recording Opera- tion About the Focus Assist FunctionIf the Record-Standby Mode Contin- ues Header REC Function Record-Standby or Stop modeFunction/Initial Setting How to set the Header REC menu screen Executing the Header REC FunctionSearch Playback ProcedureFast-Forward, Rewind Outputting Audio MIXPB Audio CH DV Audio MonitorConnecting the Video Signal Cables Connecting the IEEE1394 CableDisplaying Alarms Change 1394 SwitchRecording Composite Video Signals from an External Device Status Screen Display on the LCD Screen or ViewfinderAdjust SC and H Phase Using Genlock Func- tionsSynchronized Signals Dubbing with AV Devices HDV/DV Dubbing Videocassette you want to dubOFF Backup Recording SettingsShutter Speed in 24p Mode Connect a Remote Con- trol Unit RM-LP55/RM- LP57Remote Control Unit Functions List LoluxALC+EEI Nega OFF/ON Shutter NormalMenu Screen Configura- tion Menu Screen Configuration Cont’d Setting Menu Screens TOP Menu Screen Video FORMAT1/2 Menu Screen Function/Setting bold characters indicate initial settingsSetting Description Letter Video FORMAT1/2 Menu Screen Cont’dNative Terminal Setting B/P r Initial settings U model 7.5% E model 0.0%Video FORMAT2/2 Menu Screen AutoMenu Screen 3200KMiddle HighNormal 108%Standard Rotation Skin Color DETStop Skin Color RangePreset White Balance Menu ScreenSwitch Mode Menu Screen REC Item Setting for Step Setting for VariableAUDIO/MIC1/2 Menu Screen 20dB50dB 48KCH1/2 AUDIO/MIC2/2 Menu ScreenMIX Blue LCD/VF1/4 Menu Screen70-80% LCD Mirror Mode LCD/VF2/4 Menu ScreenImage is displayed without inverting MirrorSEC LCD/VF3/4 Menu ScreenVoltage RGB LCD/VF4/4 Menu ScreenColor Drop TC/UB/CLOCK Menu ScreenInternal Disable Header REC Menu ScreenTIME/DATE Menu Screen BARS+CAMDATE+TIME Variation Range U model MM/DD/YY E model DD/MM/YYBlink OTHERS1/2 Menu Screen3MIN OTHERS2/2 Menu Screen 1394Menu ALL Reset OTHERS2/2 Menu Screen Cont’dDR-HD100 A.OFF Drum HourSD H Phase *1 HD H PhaseGenlock Menu Screen SC Coarse *1Loading a menu settings file 100File Manage Menu Screen Displaying the File Manage menu screen101 Saving settingsError displays 102 Initializing formatting an SD mem- ory card103 How to Use Skin DetailSetting the skin detail function color and range 104 How to Use Skin Detail Cont’dUsing the Skin Detail Function Outputs multi-format color bars 105Outputting Color Bars 106 Display Status Action107 Error Code Error Details GY-HD250/GY-HD251 Remedy Operation 108Blinking Pattern Remaining Battery/Tape 109Viewfinder Screen Sound interrupted once per secondTroubleshooting Symptoms Remedy110 RGB?How to Display the Hour Meter 111Specifications 112Excluding the CHU/CHE model External Dimensions unit mm113
Related manuals
Manual 12 pages 39.42 Kb
Top Page Image Contents