JVC GY-HD250 AC Operation, Charging the Built-in Battery, How to charge the built-in battery

Page 40

e_hd250.book Page 36 Tuesday, October 24, 2006 3:11 PM

PREPARATIONS

AC Operation

The GY-HD250/GY-HD251 is operable with AC power supply or battery pack.

Use the AC adapter as the AC power supply.

1.After making sure that the power switches of the GY- HD250/GY-HD251 and of the AC adapter are set to OFF, connect the DC cable to the DC OUTPUT connector of the AC adapter and the DC INPUT connector of the GY- HD250/GY-HD251 as shown in the illustration.

•To lessen the amount of unnecessary radio waves emitted, attach a provided Clamp filter near both ends of the DC cable as shown in the diagram.

	V I D E O
	C H 2 - A U D I O O U T - C H 1
Clamp filter	IEEE 1394
	DC INPUT

DC cable

DC OUTPUT

Clamp filter

AC adapter

2.Press the POWER switch of the GY-HD250/GY-HD251 to ON. Power is supplied to the VTR section and the cam- era.

CAUTION

•Do not remove or connect the DC cable while recording is being performed.

•Do not use any power source with large fluctuations in the power source voltage, power sources generating noise, such as ripples or power sources with lower volt- age.

Charging the Built-in Battery

The built-in, rechargeable backup battery retains the date and time and the time code data.

The built-in battery is constantly being charge whenever the GY-HD250/GY-HD251 is connected to a power supply, but it gradually discharges while the GY-HD250/GY-HD251 is dis- connected from a power supply. The battery will be fully dis- charged when the GY-HD250/GY-HD251 is not used for about three months, in which case the set date and time and time code data are reset.

In this case, recharge the built-in battery and then set the date and time and time code data again.

However, it is possible to use the GY-HD250/GY-HD251 even if the built-in battery is discharged but the date and time and time code data cannot be recorded.

How to charge the built-in battery

1.Connect the AC adapter to the GY-HD250/GY-HD251 and an AC outlet or mount a charged battery on the GY- HD250/GY-HD251.

2.Set the POWER switch on the GY-HD250/GY-HD251 to “ON” or “OFF” (charging takes places with the POWER switch set to either of the positions).

3.Leave the equipment in this condition for about 4 hours.

•The built-in battery will remain charged for about 3 months after being charged for about 4 hours.

36

Image 40

Contents For Customer Use Victor Company of Japan, Limited LST0440-001BImportant Safeguards Safety Precautions RemarqueSafety Precautions Cont’d Port Cable LengthEuropean Union Information for Users on Disposal Old EquipmentBusiness users Other Countries outside the European Union HD251CHE Main Features Contents Playback Mode Precautions for Proper Use Routine and Periodical Maintenance Precautions for Use of Head Cleaning TapeHead Cleaning Periodical MaintenanceBattery Pack to be Used Videocassette to be UsedCondensation Characteristic CCD Phe- nomenaCondensation occurs in the following cases Zoom Lens Th16 × 5.5BRMUFront Section Rear Section 1Back tally lamp2PHONES Earphone jack 3Shoulder belt hooksLCD Door Right Side Section BGAIN Sensitivity selector switch CWHT.BAL White balance switchASTATUS Status/Menu button GHDV/DV LEDLeft Side Section CGENLOCK/AUX in GENLOCK/AUX in switch DPBPR/TC PBPR/Time code switchEIEEE1394 IEEE1394 switch GGENLOCK/AUX in GENLOCK/AUX in terminal BNCTop Section DMONITOR Select Audio monitor selector switch FVTR VTR indicatorGFULL Auto Full auto shooting FAS switch LScrew holes for mounting accessoriesRecording and Image Out- put Formats IEEE1394 RecordingRecording Composite Indications on the LCD Monitor and in the View- finder Status ScreensStatus Screens in the Camera Mode Setting Status Contents of IndicationsContents Indications on the LCD Monitor and in the Viewfinder Cont’dIDX Endura battery Voltage/remaining capacity % UB FF EE DDTape time appears LCD/VF3/4 menu screen. X SeeCH-1O O O O O O O O O \ \ \ CH-2O O O O O O O O O \ \ \Filter OFF ND1 ND2Indication Indication Contents Status Screen in VTR Mode HDV/DV input signalVideo Format display DoorEXT Magnified Status Indications on LCD MonitorNDF Menu Setting Screen Alarm Message DisplaySafety Zone Indication Camera mode only Safety Zone Switching between the LCD Screen and Viewfinder DisplayCenter Mark OFF Basic System HZ-ZS13BAttaching the Zoom Lens How to Attach the View- finderAttaching the Microphone Provided Inserting an SD Memory Card Taking out the SD memory cardInserting an SD Memory Card About SD Memory CardsAttaching the Tripod Base Provided only for U model How to charge the built-in battery Charging the Built-in BatteryAC Operation Battery Operation Attaching the BatteryRemoving the Battery „GY-HD250UPrecautions for the Battery Opera- tion Remaining Battery Power DisplayOperating Time with Battery Pack Precautions for the Battery PackTurning the Power on Turning the Power onTurning the Power OFF Camera modeLoading/Unloading the Cassette Cassette LoadingUnloading the Cassette ModeSetting and Displaying the Date and Time Setting the Date and Time StyleDisplaying the Time and Date on the Screen Time code input entered the IEEE1394 connector SettingDisplaying Time Code Displayed Time Code/User’s BitPresetting and Recording of Time Code SettingDrop frame/Non-drop frame mode DropPresetting user’s bit data Presetting time code dataZero-resetting the Time Code or User’s Bit Data Presetting the Time Code from the LCD Screen Presetting User’s BitAborting Preset Operation OperationPlaying Back Time Code About Time Code ModeInternal Connections Settings and OperationsSlave unit GY-HD250U/GY-HD251E/GY-HD110U/GY- HD111E Connection ExternalScreen Adjustment Viewfinder Adjustment Back Focus Adjustment White Balance Adjustment White Balance AdjustmentAdjustment procedure Error messagesWhite Shading Adjustment Setting the Frame Rate Item Setting the Video FormatSetting the REC Item Screen Size 43/169 Mode Selection Camera SettingsND Filter Audio Input Signal Selec- tion Selecting the CH-2 channel input connectorSelecting the audio signal input Adjusting Audio during RecordingMonitoring Audio during Recording LOW/MIDDLE/HIGHBasic Recording Opera- tion About the Focus Assist FunctionIf the Record-Standby Mode Contin- ues Function/Initial Setting Record-Standby or Stop modeHeader REC Function How to set the Header REC menu screen Executing the Header REC FunctionFast-Forward, Rewind Playback ProcedureSearch Outputting Audio MIXPB Audio CH DV Audio MonitorConnecting the Video Signal Cables Connecting the IEEE1394 CableDisplaying Alarms Change 1394 SwitchRecording Composite Video Signals from an External Device Status Screen Display on the LCD Screen or ViewfinderSynchronized Signals Using Genlock Func- tionsAdjust SC and H Phase Dubbing with AV Devices HDV/DV Dubbing Videocassette you want to dubOFF Backup Recording SettingsShutter Speed in 24p Mode Connect a Remote Con- trol Unit RM-LP55/RM- LP57Remote Control Unit Functions List LoluxALC+EEI Nega OFF/ON Shutter NormalMenu Screen Configura- tion Menu Screen Configuration Cont’d Setting Menu Screens TOP Menu Screen Setting Description Function/Setting bold characters indicate initial settingsVideo FORMAT1/2 Menu Screen Native Video FORMAT1/2 Menu Screen Cont’dLetter Terminal Setting B/P r Initial settings U model 7.5% E model 0.0%Video FORMAT2/2 Menu Screen AutoMenu Screen 3200KMiddle HighNormal 108%Standard Rotation Skin Color DETStop Skin Color RangePreset White Balance Menu ScreenSwitch Mode Menu Screen REC Item Setting for Step Setting for VariableAUDIO/MIC1/2 Menu Screen 20dB50dB 48KMIX AUDIO/MIC2/2 Menu ScreenCH1/2 70-80% LCD/VF1/4 Menu ScreenBlue LCD Mirror Mode LCD/VF2/4 Menu ScreenImage is displayed without inverting MirrorVoltage LCD/VF3/4 Menu ScreenSEC Color LCD/VF4/4 Menu ScreenRGB Internal TC/UB/CLOCK Menu ScreenDrop Disable Header REC Menu ScreenTIME/DATE Menu Screen BARS+CAMDATE+TIME Variation Range U model MM/DD/YY E model DD/MM/YY3MIN OTHERS1/2 Menu ScreenBlink OTHERS2/2 Menu Screen 1394Menu ALL Reset OTHERS2/2 Menu Screen Cont’dDR-HD100 A.OFF Drum HourSD H Phase *1 HD H PhaseGenlock Menu Screen SC Coarse *1Loading a menu settings file 100File Manage Menu Screen Displaying the File Manage menu screenError displays Saving settings101 102 Initializing formatting an SD mem- ory cardSetting the skin detail function color and range How to Use Skin Detail103 Using the Skin Detail Function How to Use Skin Detail Cont’d104 Outputting Color Bars 105Outputs multi-format color bars 106 Display Status Action107 Error Code Error Details GY-HD250/GY-HD251 Remedy Operation 108Blinking Pattern Remaining Battery/Tape 109Viewfinder Screen Sound interrupted once per secondTroubleshooting Symptoms Remedy110 RGB?How to Display the Hour Meter 111Specifications 112113 External Dimensions unit mmExcluding the CHU/CHE model

Related manuals

Manual 12 pages 39.42 Kb