Axis Communications Q6045S Symptoms, Possible Causes and Remedial Actions, When using ARP/Ping

Page 60

AXIS Q6045–S PTZ Dome Network Camera

Troubleshooting

arp -s <IP address> <serial number> temp ping -l 408 <IP address>

In Windows, type the following from a command/DOS prompt (this may require that you run the command prompt as an administrator):

arp -s <IP address> <serial number> ping -l 408 -t <IP address>

2.If the product does not reply in 30 seconds, restart it and wait for a reply. Press CTRL+C to stop Ping.

3.Open a browser and type in the product’s IP address. In the page that opens, use the Browse button to select the upgrade file to use. Then click Load to restart the upgrade process.

4.After the upgrade is complete (1–10 minutes), the product automatically restarts and shows a steady green on the Status indicator.

5.Reinstall the product, referring to the Installation Guide.

If the emergency recovery procedure does not get the product up and running again, contact Axis support at www.axis.com/techsup/

Symptoms, Possible Causes and Remedial Actions

Problems setting the IP address

When using ARP/Ping

Try the installation again. The IP address must be set within two minutes after power has been

 

applied to the product. Ensure the Ping length is set to 408. For instructions, see Assign IP Address

 

Using ARP/Ping, on page 49.

The product is located on a different subnet

The IP address is being used by another device

Possible IP address conflict with another device on the same subnet.

If the IP address intended for the product and the IP address of the computer used to access the product are located on different subnets, you will not be able to set the IP address. Contact your network administrator to obtain an IP address.

Disconnect the Axis product from the network. Run the Ping command (in a Command/DOS window, type ping and the IP address of the product):

•If you receive: Reply from <IP address>: bytes=32; time=10...

this means that the IP address may already be in use by another device on the network. Obtain a new IP address from the network administrator and reinstall the product.

•If you receive: Request timed out, this means that the IP address is available for use with the Axis product. Check all cabling and reinstall the product.

The static IP address in the Axis product is used before the DHCP server sets a dynamic address. This means that if the same default static IP address is also used by another device, there may be problems accessing the product.

The product cannot be accessed from a browser

Cannot log in

When HTTPS is enabled, ensure that the correct protocol (HTTP or HTTPS) is used when attempting

 

to log in. You may need to manually type http or https in the browser’s address field.

 

If the password for the user root is lost, the product must be reset to the factory default settings.

 

See Reset to Factory Default Settings, on page 57.

60

Page 59 Page 61
Image 60
Page 59 Page 61
Contents Axis Q6045-S PTZ Dome Network Camera About this Document Legal ConsiderationsLiability Intellectual Property RightsSupport Learn MoreTable of Contents Axis Q6045-S PTZ Dome Network CameraSupport Advanced Reset to Factory Default Settings Media Converter Switch Connectors Performance ConsiderationsHardware Overview Hardware OverviewPressurize the Camera Recommended Connectors and Buttons LED IndicatorsMulti-connector SD Card SlotHardware Overview Media Converter Switch Media Converter Switch ConnectorsNetwork Connector Dip Switches Dip switch positionConnector internal 2-pin I/O terminal block Media Converter Switch LED Indicators DescriptionAccessing the Product Accessing the ProductAccess from a Browser Start a browser Internet Explorer, Firefox, SafariAccessing the Product Access from the Internet Set the Root PasswordClick Use Https Accessing the Product Live View Go to Setup EventsControls on the Live View Manual TriggerAxis Media Control viewer toolbar PTZ ControlsAxis Q6045-S PTZ Dome Network Camera How to Stream H.264 Media StreamsMedia Streams Axis Media Control AMCAlternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAxis Q6045-S PTZ Dome Network Camera Setting Up the Product Setting Up the ProductBasic Setup Video VideoVideo Stream Pixel CounterClick Save to apply the new settings Stream ProfilesImage 264Camera Settings Exposure SettingsImage Appearance White BalanceImage Settings OverlayOverlay Image Go to Video Video Stream and select the Image tabUsing Overlay Text in an Action Rule Privacy MaskGo to Events Action Rules Axis Q6045-S PTZ Dome Network Camera Live View Config Live View ConfigDefault Viewer for Browsers Viewer SettingsUser Defined Links Output ButtonsGo to Setup Live View Config Preset Positions Go to PTZ Preset PositionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomConfiguration PTZ Pan Tilt Zoom GatekeeperAutotracking Exclude AreasGuard Tour Tour RecordingTo add a guard tour To add a recorded tourOsdi Zones AdvancedLimits Operator Same as administrator but with lower priority Control QueueControls Set Up Motion Detection Windows DetectorsDetectors Shock DetectionObject Removed Motion Detection ParametersEnter/Exit Detector Fence DetectorObject Counter Install Application ApplicationsApplications Application LicensesAxis Q6045-S PTZ Dome Network Camera Input Signal EventsEvents DetectorsSetting Up an Action Rule StorageSystem TimeRecipients Fallback ActionGo to Events Action Rules and click Add RecipientSetting Up an Email Recipient SchedulesGo to Events Recipients and click Add Go to Events Schedules and click AddRecurrences Go to Events Recurrences and click AddRecordings RecordingsRecording List Continuous RecordingLanguages LanguagesSystem Options System OptionsSecurity UsersIeee CertificatesGo to System Options Security Ieee Basic TCP/IP Settings Go to Setup System Options Security CertificatesDate & Time NetworkIPv4 Address Configuration IPv6 Address ConfigurationAssign IP Address Using ARP/Ping ARP/PingAdvanced TCP/IP Settings Axis Internet Dynamic DNS ServiceAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationNTP Configuration Host Name ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service FTPStorage UPnPTMRTP/H.264 BonjourNetwork Share Go to System Options Storage and click SD CardTo add a network share Go to System Options Storage Click Network ShareMaintenance System Options Ports & DevicesSupport Plain Config Logs & ReportsScripting File UploadSystem Options Reset to Factory Default Settings Multi-Connector Cable Multi-Connector CableFunction Pin wire Specifications Activated, floating unconnected when Drain, 100 mATroubleshooting TroubleshootingEmergency Recovery Procedure Checking the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressWhen using ARP/Ping Product cannot be accessed from a browserProduct is accessible locally but not externally Problems with streaming H.264Basic Video and image problems, general Video Camera SettingsStorage and disk management problems Media converter switchTechnical Specifications Technical SpecificationsFunction/group Specifications System Application Installation aidMaintenance Integration Programming InterfaceFunction/group Specifications General Casing PowerConnectors WeightTechnical Specifications Media Converter Switch Connectors Camera ConnectorsExternal Connectors Performance Considerations Collector 100 mAM1.7
Top Page Image Contents