Axis Communications Q6044-C user manual Overlay, Image Settings

Page 22

AXIS Q6044-C PTZ Dome Network Camera

Video

Max gain - Measured in decibels (dB), gain describes the amount of amplification applied to a signal, in this case the visual information in the image. A high level of amplification may provide a better image in very low light situations. A high gain will also increase the amount of image noise.

Exposure zones - This settings determines which part of the image is used to calculate the exposure. For most situations, the Auto setting can be used. For particular requirement, select a predefined area.

IR cut filter - The IR cut filter prevents infrared (IR) light from reaching the image sensor. In poor lighting conditions, for example at night, or when using an external IR lamp, set the IR cut filter to Off. This increases light sensitivity and allows the product to “see” infrared light. The image is shown in black and white when the IR cut filter is off. Set the IR cut filter to Auto to automatically switch between On and Off according to the lighting conditions.

Day/Night shift priority - Use the Day/Night shift priority bar to determine when the camera shifts into either day mode or night mode. By default, the camera will automatically change from day to night mode at a pre-defined level which corresponds to light conditions. By dragging the bar handle towards the sun, the camera will change to day mode earlier and change to night mode late.

Image Settings

Autofocus enabled - Automatic focusing is enabled by default. If the focus position is changed manually using the focus bar, autofocus will be disabled even if enabled here. In this case, use the PTZ control panel to enable autofocus, see PTZ Controls on page 13. If required, the focus control can be disabled under PTZ > Advanced > Controls.

Auto defog - The product will detect fog and automatically filter it out to get a clear image. Select the level of fog removal from the drop-down list. High implies that maximum fog removal is applied and off implies no fog removal. Auto defog can be activated incorrectly in scenes with low contrast, high light level variations or when auto focus is slightly off. This can affect the image quality by for example, increasing image contrast. Also, too much brightness can negatively impact the image quality when defog is active.

Noise reduction - Set to On to enable noise reduction. Noise reduction may increase the amount of motion blur.

Stabilizer - When monitoring environments that are subject to vibrations (e.g. traffic control), images may appear to be unsteady. Select the frequency, High or Low, that gives the best improvement in image quality. Enabling the stabilizer will limit the digital

zoom. See the online help for more information.

Image freeze on PTZ - Select All movements to freeze the image while the camera is moving during a pan, tilt or zoom operation. Once the camera reaches its new position, the view from that position is shown. Presets freezes the image only when the camera moves between preset positions.

Overlay

Overlays are used to provide extra information, for example for forensic video analysis or during product installation and configuration. Overlays are superimposed over the video stream.

An overlay text can display the current date and time, or a text string. When using a text string, modifiers can be used to display information such as the current bit rate or the current frame rate. For information about available modifiers, see File Naming &

Date/Time Formats in the online help .

It is also possible to display text when an action rule is triggered, see Use Overlay Text in an Action Rule.

To enable overlays:

1.Go to Video > Video Stream and select the Image tab.

2.To include an overlay image, select Include overlay image at the coordinates. The overlay image must first be uploaded to the Axis product, see Overlay Image.

3.To include date and time, select Include date and Include time.

4.To include a text string, select Include text and enter the text in the field. Modifiers can be used, see File Naming &

Date/Time Formats in the online help .

5.Define text overlay characteristics in the relevant fields.

22

Image 22
Contents Axis Q6044-C PTZ Dome Network Camera Liability About this DocumentLegal Considerations Intellectual Property RightsSupport Learn MoreTable of Contents Axis Q6044-C PTZ Dome Network CameraMulti-Connector Cable Troubleshooting Hardware Overview Connectors and ButtonsFor technical specifications, see CameraPower Button LED IndicatorsMulti-connector SD Card SlotMedia Converter Switch Media Converter Switch ConnectorsDip switch position Network Connector Dip SwitchesConnector internal 2-pin I/O terminal block Media Converter Switch LED Indicators DescriptionAccess from the Internet Access the ProductAccess from a Browser Set the Root PasswordControls on the Live View Go to Setup EventsLive View Click Use HttpsPTZ Controls Axis Media Control viewer toolbarTo show the manual trigger buttons in the Live View Axis Q6044-C PTZ Dome Network Camera Media Streams How to Stream H.264Axis Media Control AMC Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAxis Q6044-C PTZ Dome Network Camera Set Up the Product Basic SetupVideo Stream VideoPixel Counter Image Click Save to apply the new settings264 Camera Settings Stream ProfilesOverlay Image SettingsGo to Video Video Stream and select the Image tab Use Overlay Text in an Action Rule Overlay ImageGo to Video Overlay Image Start by enabling overlay text in the video stream Privacy MaskGo to Events Action Rules Viewer Settings Configure the Live ViewDefault Viewer for Browsers Browser Viewer DescriptionOutput Buttons Go to Setup Live View ConfigUser Defined Links For more information about I/O ports, see I/O Ports onClick Add to save the preset position Preset PositionsGo to PTZ Preset Positions PTZ Pan Tilt ZoomAutotracking ConfigurationGatekeeper Exclude AreasMax Limits Guard TourTo add a guard tour Tour Recording Osdi ZonesAdvanced LimitsControl Queue Operator Same as administrator but with lower priorityControls Axis Q6044-C PTZ Dome Network Camera Shock Detection Set Up Motion Detection WindowsDetectors Motion DetectionHigh level 100% Default valuesParameter Object Size History Sensitivity Description Medium level 50%Applications Install ApplicationGo to Setup Applications Application LicensesAxis Q6044-C PTZ Dome Network Camera Triggers Set Up Action RulesEvents Go to Events Action Rules and click AddActions Add Recipients Recipient TypesCreate Schedules Set Up RecurrencesSet Up Email Recipients Go to Events Schedules and click AddAxis Q6044-C PTZ Dome Network Camera Continuous Recording RecordingsRecording List Go to Recordings ListLanguages Users System OptionsSecurity IP Address FilterCertificates IeeeGo to System Options Security Ieee Date & Time Basic TCP/IP SettingsGo to Setup System Options Security Certificates NetworkAssign IP Address Using ARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration ARP/PingAxis Internet Dynamic DNS Service requires IPv4 Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service DNS ConfigurationLink-Local IPv4 Address NTP ConfigurationHost Name Configuration NAT traversal port mapping for IPv4QoS Quality of Service Smtp emailRTP/H.264 UPnPTM can be disabled under System Options Network UPnPTMUPnPTM BonjourMount and Unmount SD Card StorageSD Card Format SD CardNetwork Share MaintenancePorts & Devices PortsSystem Overview SupportSupport Overview Logs & ReportsScripting Reset to Factory Default SettingsPlain Config File UploadAxis Q6044-C PTZ Dome Network Camera Activated, floating unconnected when Drain, 100 mA Multi-Connector CableFunction Pin wire Specifications Green/white Ethernet receivingEmergency Recovery Procedure TroubleshootingUpgrade the Firmware Check the FirmwareProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product is accessible locally but not externallyVideo Camera Settings Problems with streaming H.264Video and image problems, general Key framesStorage disruption Storage and disk management problemsMedia converter switch Re-mount the storage deviceTechnical Specifications Maintenance Function/group Specifications System ApplicationInstallation aid PowerConnectors Camera ConnectorsNetwork connector External ConnectorsFunction Pin Specifications Terminal connectorPerformance Considerations M5.2
Related manuals
Manual 67 pages 21.72 Kb