Axis Communications Q6044-C user manual UPnPTM, RTP/H.264, Bonjour

Page 51

AXIS Q6044-C PTZ Dome Network Camera

System Options

To enable and configure SNMP in the Axis product, go to the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

Cold start

Warm start

Link up

Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 44. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 55.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

51

Image 51
Contents Axis Q6044-C PTZ Dome Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis Q6044-C PTZ Dome Network Camera Table of ContentsMulti-Connector Cable Troubleshooting Camera Connectors and ButtonsFor technical specifications, see Hardware OverviewSD Card Slot LED IndicatorsMulti-connector Power ButtonMedia Converter Switch Connectors Media Converter SwitchNetwork Connector Dip Switches Dip switch positionConnector internal 2-pin I/O terminal block Description Media Converter Switch LED IndicatorsSet the Root Password Access the ProductAccess from a Browser Access from the InternetClick Use Https Go to Setup EventsLive View Controls on the Live ViewAxis Media Control viewer toolbar PTZ ControlsTo show the manual trigger buttons in the Live View Axis Q6044-C PTZ Dome Network Camera How to Stream H.264 Media StreamsAxis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis Q6044-C PTZ Dome Network Camera Basic Setup Set Up the ProductVideo Video StreamPixel Counter Click Save to apply the new settings Image264 Stream Profiles Camera SettingsImage Settings OverlayGo to Video Video Stream and select the Image tab Overlay Image Use Overlay Text in an Action RuleGo to Video Overlay Image Privacy Mask Start by enabling overlay text in the video streamGo to Events Action Rules Browser Viewer Description Configure the Live ViewDefault Viewer for Browsers Viewer SettingsFor more information about I/O ports, see I/O Ports on Go to Setup Live View ConfigUser Defined Links Output ButtonsPTZ Pan Tilt Zoom Preset PositionsGo to PTZ Preset Positions Click Add to save the preset positionExclude Areas ConfigurationGatekeeper AutotrackingGuard Tour Max LimitsTo add a guard tour Limits Osdi ZonesAdvanced Tour RecordingOperator Same as administrator but with lower priority Control QueueControls Axis Q6044-C PTZ Dome Network Camera Motion Detection Set Up Motion Detection WindowsDetectors Shock DetectionMedium level 50% Default valuesParameter Object Size History Sensitivity Description High level 100%Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis Q6044-C PTZ Dome Network Camera Go to Events Action Rules and click Add Set Up Action RulesEvents TriggersActions Recipient Types Add RecipientsGo to Events Schedules and click Add Set Up RecurrencesSet Up Email Recipients Create SchedulesAxis Q6044-C PTZ Dome Network Camera Go to Recordings List RecordingsRecording List Continuous RecordingLanguages IP Address Filter System OptionsSecurity UsersIeee CertificatesGo to System Options Security Ieee Network Basic TCP/IP SettingsGo to Setup System Options Security Certificates Date & TimeARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration Assign IP Address Using ARP/PingDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressSmtp email QoS Quality of ServiceBonjour UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264Format SD Card StorageSD Card Mount and Unmount SD CardPorts MaintenancePorts & Devices Network ShareLogs & Reports SupportSupport Overview System OverviewFile Upload Reset to Factory Default SettingsPlain Config ScriptingAxis Q6044-C PTZ Dome Network Camera Green/white Ethernet receiving Multi-Connector CableFunction Pin wire Specifications Activated, floating unconnected when Drain, 100 mACheck the Firmware TroubleshootingUpgrade the Firmware Emergency Recovery ProcedureProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserKey frames Problems with streaming H.264Video and image problems, general Video Camera SettingsRe-mount the storage device Storage and disk management problemsMedia converter switch Storage disruptionTechnical Specifications Power Function/group Specifications System ApplicationInstallation aid MaintenanceCamera Connectors ConnectorsTerminal connector External ConnectorsFunction Pin Specifications Network connectorPerformance Considerations M5.2
Related manuals
Manual 67 pages 21.72 Kb