Axis Communications P5414E user manual PTZ Controls, AMC Audio Controls

Page 11

AXIS P5414–E PTZ Dome Network Camera

Accessing the Product

Click the View Full Screen button and the video image will fill the entire screen. Press ESC (Escape) on the computer keyboard to cancel full screen view.

The Record button is used to record the current video stream. The location where the recording is saved can be specified in the AMC Control Panel. Enable this button from Live View Config > Viewer Settings.

AMC Audio Controls

AMC audio buttons control the speakers and microphone connected to the client computer. The buttons are only visible when audio is enabled.

Speaker button — Click to turn the speakers on or off.

Microphone button – Click to mute or unmute the microphone. In Simplex - speaker only mode, the Microphone and Talk buttons must both be active to send audio to the Axis product. Click either button to stop audio transmission.

Use the slider to control the volume of the speakers and the microphone.

Half-duplex mode

The Talk/Listen button is used to switch between sending and receiving audio. The button can be configured from the Audio tab in the AMC Control panel:

•Push-To-Talk mode: Click and hold the button to talk/send. Release the button to listen.

•Toggle mode: Click once to switch between talking and listening.

Simplex – speaker only mode

To send audio, the Talk and Microphone buttons must both be active. Click either button to stop audio transmission.

PTZ Controls

The Live View page also displays Pan/Tilt/Zoom (PTZ) controls. The administrator can enable/disable controls for specified users under System Options > Security > Users.

With the PTZ Control Queue enabled the time each user is in control of the PTZ settings is limited. Click the buttons to request or release control of the PTZ controls. The PTZ Control Queue is set up under PTZ > Control Queue.

Select Focus window to define an area of the camera's image that focus should be applied on. If the focus window is set from the Live View page, any change in the camera position will return the autofocus to the entire window. To set a permanent focus window, see Preset Positions, on page 27

Click the Emulate joystick mode button and click in the image to move the camera view in the direction of the mouse pointer.

Click the Center mode button and click in the image to center the camera view on that position. The center mode button could also be used to zoom in on a specific area. Click in the image and drag to draw a rectangle surrounding the area to be magnified. To zoom out, rotate the mouse wheel.

Click the Ctrl panel button to open the PTZ control panel which provides additional PTZ controls.

User-defined buttons can also appear in the Control panel. See Controls, on page 29.

Select a PTZ preset position to steer the camera view to the saved position. See Preset Positions, on page 27.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Axis P5414-E PTZ Dome Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis P5414-E PTZ Dome Network Camera Table of ContentsTechnical Specifications Hardware Overview Connectors and ButtonsNetwork Connector Hardware OverviewLED Indicators Access from a Browser Accessing the ProductAccessing the Product Controls on the Live View Accessing the Product Access from the InternetSet the Root Password Live ViewManual Trigger Go to Setup EventsAxis Media Control viewer toolbar AMC Audio Controls PTZ ControlsAxis P5414-E PTZ Dome Network Camera Axis Media Control AMC How to Stream H.264Media Streams Media StreamsAlternative Methods of Accessing the Video Stream Accessing Audio Streams Basic Setup Setting Up the ProductSetting Up the Product Image Video and AudioVideo and Audio Video Stream264 Camera SettingsStream Profiles Wide Dynamic Range Exposure SettingsImage Appearance White BalanceGo to Video & Audio Video Stream and select the Image tab OverlayDay/Night Go to Events Action Rules Using Overlay Text in an Action RuleOverlay Image Go to Video & Audio Overlay ImageAudio Input Audio SettingsVideo and Audio Privacy Mask Audio ModesAudio Output Audio ClipsDefault Viewer for Browsers Live View ConfigLive View Config Output Buttons Viewer SettingsGo to Setup Live View Config User Defined LinksAxis P5414-E PTZ Dome Network Camera Focus Window Preset PositionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomGo to PTZ Guard Tour and click Add PTZ Pan Tilt Zoom GatekeeperGuard Tour Osdi ZonesControls AdvancedControl Queue LimitsAxis P5414-E PTZ Dome Network Camera Motion Detection Set Up Motion Detection WindowsDetectors DetectorsMotion Detection Parameters Audio DetectionApplication Licenses Install ApplicationApplications ApplicationsAxis P5414-E PTZ Dome Network Camera Events EventsPTZ Control Setting Up an Action RuleSystem TimeGo to Events Recipients and click Add RecipientsFallback Action Recipient Use with actionGo to Events Schedules and click Add Setting Up an Email RecipientSchedules RecurrencesGo to Events Recurrences and click Add Continuous Recording RecordingsRecordings Recording ListLanguages LanguagesUsers System OptionsSystem Options SecurityGo to System Options Security Ieee IeeeCertificates Go to System Options Security Certificates Date & TimeAudio Support System Options Network Basic TCP/IP SettingsAxis Video Hosting System Avhs Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service DNS ConfigurationNAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressSmtp email QoS Quality of ServiceRTP/H.264 UPnPTM can be disabled under System Options Network UPnPTMUPnPTM Network Share StorageBonjour SD CardPort Status MaintenancePorts & Devices PortsLogs & Reports SupportSupport Overview System OverviewFile Upload Reset to Factory Default SettingsPlain Config Repainting the Camera Repainting the CameraChecking the Firmware TroubleshootingTroubleshooting Emergency Recovery ProcedureProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Basic Product is accessible locally but not externallyProblems with streaming H.264 Storage and disk management problems Video and image problems, generalSetup Video & Audio Camera Settings SettingsTechnical Specifications Technical SpecificationsSupported Function/group Specifications Network SecurityInstallation MaintenanceTerminal Connector ConnectorsO configured as input O configured as output Function Pin Performance ConsiderationsM2.2

P5414E specifications

The Axis Communications P5414E is a high-performance pan-tilt-zoom (PTZ) network camera designed for versatile surveillance applications. Ideal for outdoor environments, this camera combines advanced imaging technology with sophisticated features, catering to the needs of security professionals looking for reliable performance.

One of the standout features of the P5414E is its 720p resolution capability, providing clear and sharp images for effective monitoring. The camera is equipped with a powerful 18x optical zoom, enabling users to zoom in on specific areas without losing image quality. This is particularly useful in scenarios where detailed surveillance is crucial, such as monitoring large open spaces or capturing high-definition images of distant subjects.

The P5414E employs Axis’ streaming technology, allowing for smooth and efficient video transmission over the network. It supports multiple H.264 and Motion JPEG streams, enabling users to customize the stream quality depending on their networking conditions and storage needs. This flexibility is essential for optimizing bandwidth usage while maintaining image fidelity.

For nighttime surveillance, the P5414E incorporates advanced infrared (IR) technology, allowing it to capture high-quality images even in low-light conditions. With a built-in IR illuminator, the camera can provide visibility in complete darkness, ensuring continuous monitoring around the clock.

The camera's rugged design is specifically built to withstand harsh weather conditions. It includes an IP66-rated housing, making it resistant to dust and water ingress, while also operating effectively in a temperature range of -40°C to 50°C (-40°F to 122°F). This durability makes the P5414E suitable for a variety of challenging environments.

In addition to its robust features, the P5414E includes Axis’ advanced analytic functionalities, such as digital auto tracking and motion detection. These features enhance the camera's capability to alert users of suspicious activities in real time, significantly improving the effectiveness of security operations.

Moreover, the camera is equipped with Power over Ethernet (PoE), simplifying installation and reducing the need for multiple cables. This integration of power and data transmission through a single cable not only streamlines setup but also ensures a more efficient and reliable operation.

The Axis Communications P5414E represents the pinnacle of surveillance technology, combining high-resolution video, robust features, and practical design to meet the demands of modern security environments. Its cutting-edge technologies provide users with the tools needed for comprehensive monitoring and effective response to security threats.
Top Page Image Contents