Axis Communications P5414E user manual UPnPTM, RTP/H.264

Page 49

AXIS P5414–E PTZ Dome Network Camera

System Options

Enter the host names or IP addresses and port numbers for the primary and secondary mail servers in the fields provided. A From email address is also required. If the mail server requires authentication, check Use authentication to log in to this server and enter the necessary information.

SNMP

The Simple Network Management Protocol (SNMP) allows remote management of network devices. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups.

The Axis product can be configured to support SNMP on the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

SNMP v1/v2 provides the lowest level of security. The community name can be specified as a password for read or read/write access to all supported SNMP devices. The default password for the Read community is public and the default password for the Write community is write.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS, on page 42. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings, on page 53.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video and/or Always Multicast Audio to start multicast streaming without opening an RTSP session.

49

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Axis P5414-E PTZ Dome Network Camera Legal Considerations About this DocumentLiability Intellectual Property RightsLearn More SupportAxis P5414-E PTZ Dome Network Camera Table of ContentsTechnical Specifications Network Connector Connectors and ButtonsHardware Overview Hardware OverviewLED Indicators Accessing the Product Accessing the ProductAccess from a Browser Set the Root Password Accessing the Product Access from the InternetLive View Controls on the Live ViewAxis Media Control viewer toolbar Go to Setup EventsManual Trigger AMC Audio Controls PTZ ControlsAxis P5414-E PTZ Dome Network Camera Media Streams How to Stream H.264Media Streams Axis Media Control AMCAlternative Methods of Accessing the Video Stream Accessing Audio Streams Setting Up the Product Setting Up the ProductBasic Setup Video and Audio Video and AudioVideo Stream ImageStream Profiles Camera Settings264 Image Appearance Exposure SettingsWhite Balance Wide Dynamic RangeDay/Night OverlayGo to Video & Audio Video Stream and select the Image tab Overlay Image Using Overlay Text in an Action RuleGo to Video & Audio Overlay Image Go to Events Action RulesVideo and Audio Privacy Mask Audio SettingsAudio Modes Audio InputAudio Output Audio ClipsLive View Config Live View ConfigDefault Viewer for Browsers Go to Setup Live View Config Viewer SettingsUser Defined Links Output ButtonsAxis P5414-E PTZ Dome Network Camera PTZ Pan Tilt Zoom Preset PositionsPTZ Pan Tilt Zoom Focus WindowGuard Tour PTZ Pan Tilt Zoom GatekeeperOsdi Zones Go to PTZ Guard Tour and click AddControl Queue AdvancedLimits ControlsAxis P5414-E PTZ Dome Network Camera Detectors Set Up Motion Detection WindowsDetectors Motion DetectionMotion Detection Parameters Audio DetectionApplications Install ApplicationApplications Application LicensesAxis P5414-E PTZ Dome Network Camera Events EventsSystem Setting Up an Action RuleTime PTZ ControlFallback Action RecipientsRecipient Use with action Go to Events Recipients and click AddSchedules Setting Up an Email RecipientRecurrences Go to Events Schedules and click AddGo to Events Recurrences and click Add Recordings RecordingsRecording List Continuous RecordingLanguages LanguagesSystem Options System OptionsSecurity UsersCertificates IeeeGo to System Options Security Ieee Audio Support Date & TimeGo to System Options Security Certificates System Options Network Basic TCP/IP SettingsAxis Internet Dynamic DNS Service Advanced TCP/IP SettingsDNS Configuration Axis Video Hosting System AvhsHost Name Configuration NTP ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4Smtp email QoS Quality of ServiceUPnPTM UPnPTM can be disabled under System Options Network UPnPTMRTP/H.264 Bonjour StorageSD Card Network SharePorts & Devices MaintenancePorts Port StatusSupport Overview SupportSystem Overview Logs & ReportsPlain Config Reset to Factory Default SettingsFile Upload Repainting the Camera Repainting the CameraTroubleshooting TroubleshootingEmergency Recovery Procedure Checking the FirmwareProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Problems with streaming H.264 Product is accessible locally but not externallyBasic Setup Video & Audio Camera Settings Video and image problems, generalSettings Storage and disk management problemsTechnical Specifications Technical SpecificationsInstallation Function/group Specifications Network SecurityMaintenance SupportedTerminal Connector ConnectorsO configured as input O configured as output Function Pin Performance ConsiderationsM2.2

P5414E specifications

The Axis Communications P5414E is a high-performance pan-tilt-zoom (PTZ) network camera designed for versatile surveillance applications. Ideal for outdoor environments, this camera combines advanced imaging technology with sophisticated features, catering to the needs of security professionals looking for reliable performance.

One of the standout features of the P5414E is its 720p resolution capability, providing clear and sharp images for effective monitoring. The camera is equipped with a powerful 18x optical zoom, enabling users to zoom in on specific areas without losing image quality. This is particularly useful in scenarios where detailed surveillance is crucial, such as monitoring large open spaces or capturing high-definition images of distant subjects.

The P5414E employs Axis’ streaming technology, allowing for smooth and efficient video transmission over the network. It supports multiple H.264 and Motion JPEG streams, enabling users to customize the stream quality depending on their networking conditions and storage needs. This flexibility is essential for optimizing bandwidth usage while maintaining image fidelity.

For nighttime surveillance, the P5414E incorporates advanced infrared (IR) technology, allowing it to capture high-quality images even in low-light conditions. With a built-in IR illuminator, the camera can provide visibility in complete darkness, ensuring continuous monitoring around the clock.

The camera's rugged design is specifically built to withstand harsh weather conditions. It includes an IP66-rated housing, making it resistant to dust and water ingress, while also operating effectively in a temperature range of -40°C to 50°C (-40°F to 122°F). This durability makes the P5414E suitable for a variety of challenging environments.

In addition to its robust features, the P5414E includes Axis’ advanced analytic functionalities, such as digital auto tracking and motion detection. These features enhance the camera's capability to alert users of suspicious activities in real time, significantly improving the effectiveness of security operations.

Moreover, the camera is equipped with Power over Ethernet (PoE), simplifying installation and reducing the need for multiple cables. This integration of power and data transmission through a single cable not only streamlines setup but also ensures a more efficient and reliable operation.

The Axis Communications P5414E represents the pinnacle of surveillance technology, combining high-resolution video, robust features, and practical design to meet the demands of modern security environments. Its cutting-edge technologies provide users with the tools needed for comprehensive monitoring and effective response to security threats.
Top Page Image Contents