Axis Communications P3367VE user manual Network, Basic TCP/IP Settings

Page 50

AXIS P3367–VE Fixed Dome Network Camera

System Options

Network

Basic TCP/IP Settings

The Axis product supports IP version 4 and IP version 6. Both versions can be enabled simultaneously, and at least one version must always be enabled.

IPv4 Address Configuration

By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP. The IPv4 settings are configured under System Options > Network > TCP/IP > Basic.

DHCP (Dynamic Host Configuration Protocol) allows network administrators to centrally manage and automate the assignment of IP addresses. DHCP should only be enabled if using dynamic IP address notification, or if the DHCP can update a DNS server. It is then possible to access the Axis product by name (host name).

If DHCP is enabled and the product cannot be accessed, run AXIS IP Utility to search the network for connected Axis products, or reset the product to the factory default settings (see page 59) and then perform the installation again.

To use a static IP address, check Use the following IP address and specify the IP address, subnet mask and default router.

IPv6 Address Configuration

If IPv6 (IP version 6) is enabled, the Axis product will receive an IP address according to the configuration in the network router.

To enable IPv6, go to System Options > Network > TCP/IP > Basic. Other settings for IPv6 should be configured in the network router.

ARP/Ping

The product’s IP address can be assigned using ARP and Ping. For instructions, see Assign IP Address Using ARP/Ping on page 50.

The ARP/Ping service is enabled by default but is automatically disabled two minutes after the product is started, or as soon as an IP address is assigned. To re-assign IP address using ARP/Ping, the product must be restarted to enable ARP/Ping for an additional two minutes.

To disable the service, go to System Options > Network > TCP/IP > Basic and clear the option Enable ARP/Ping setting of IP address.

Pinging the product is still possible when the service is disabled.

Assign IP Address Using ARP/Ping

The product's IP address can be assigned using ARP/Ping. The command must be issued within 2 minutes of connecting power.

1.Acquire a free static IP address on the same network segment as the computer.

2.Locate the serial number (S/N) on the product label.

3.Open a command prompt and enter the following commands:

Linux/Unix syntax

arp -s <IP address> <serial number> temp ping -s 408 <IP address>

Linux/Unix example

arp -s 192.168.0.125 00:40:8c:18:10:00 temp ping -s 408 192.168.0.125

Windows syntax (this may require that you run the command prompt as an administrator) arp -s <IP address> <serial number>

50

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Axis P3367-VE Fixed Dome Network Camera Liability About this documentLegal Considerations Intellectual Property RightsSupport Learn MoreTable of Contents Axis P3367-VE Fixed Dome Network CameraConnectors Performance Considerations Hardware Overview Connectors and Buttons LED Indicators Color IndicationStart a browser Internet Explorer, Firefox, Safari Access the ProductAccess from a Browser Click Use Https Access from the InternetSet the Root Password Live View Set Power Line FrequencyConfigure Capture Mode Controls on the Live ViewManual Trigger Go to Setup EventsAxis Media Control viewer toolbar To show the manual trigger buttons in the Live ViewPTZ Controls Speaker button Click to turn the speakers on or offAxis Media Control AMC How to Stream H.264Media Streams Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAccess Audio Streams Java applet supports simplex audio with G.711 encodingSet Up the Product Basic SetupVideo and Audio Video StreamImage Click Save to apply the new settingsPixel Counter 264Stream Profiles Camera SettingsCapture Mode White Balance Go to Setup Video & Audio Camera SettingsImage Appearance Wide Dynamic RangeShutter & Gain Exposure SettingsIris adjustment Set Shutter toOverlay Select an Aspect ratio and a Video stream resolutionView Area Day/NightGo to Video & Audio Video Stream and select the Image tab To enable overlaysOverlay Image Go to Video & Audio Overlay ImageUse Overlay Text in an Action Rule Privacy MaskFocus & Zoom Go to Events Action RulesAudio Modes Audio SettingsWhen satisfied, click Enable iris to enable the iris Audio InputAudio Clips Audio OutputConfigure the Live View Default Viewer for BrowsersUser Defined Links Viewer SettingsGo to Setup Live View Config Output ButtonsAxis P3367-VE Fixed Dome Network Camera PTZ Pan Tilt Zoom Preset PositionsGo to PTZ Preset Positions Controls Guard TourAdvanced To add a guard tourOperator Same as administrator but with lower priority Control QueueMotion Detection DetectorsCamera Tampering Go to Detectors Camera TamperingGo to Detectors Motion Detection Set Up Motion Detection WindowsMotion Detection Parameters Parameter Object Size History Sensitivity DescriptionAudio Detection Applications Install ApplicationGo to Setup Applications Application LicensesAxis P3367-VE Fixed Dome Network Camera Triggers Set Up Action RulesEvents Go to Events Action Rules and click AddStorage Input SignalHardware SystemRecipient Types Add RecipientsActions PTZ ControlSet Up Email Recipients Recipient Use with actionTo create a new schedule Set Up RecurrencesCreate Schedules Go to Events Schedules and click AddPlay Recording RecordingsFind Recordings Go to Recordings ListTo play a recording, follow these steps Export Video ClipContinuous Recording Go to Recordings ContinuousLanguages Users System OptionsSecurity IP Address FilterGo to System Options Security Ieee IeeeCertificates Click Install certificate and upload the certificate To install a self-signed certificateGo to Setup System Options Security Certificates Date & TimeBasic TCP/IP Settings NetworkAxis Internet Dynamic DNS Service requires IPv4 Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service DNS ConfigurationLink-Local IPv4 Address NTP ConfigurationHost Name Configuration NAT traversal port mapping for IPv4QoS Quality of Service FTPRTP/H.264 UPnPTM can be disabled under System Options Network UPnPTMUPnPTM SD Card StorageBonjour Mount and Unmount SD CardTo add a network share Under General Settings, select Autoformat toNetwork Share Go to System Options Storage Click Network ShareSupport MaintenancePorts & Devices Scripting System OverviewLogs & Reports File UploadReset to Factory Default Settings Plain ConfigFirmware To upgrade the product’s firmware TroubleshootingUpgrade the Firmware Check the FirmwareProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsEmergency Recovery Procedure Product cannot be accessed from a browserBasic Product is accessible locally but not externallyProblems with streaming H.264 Setup Video & Audio Camera Settings Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general SettingsStorage and disk management problems Focus, zoom, and fanTechnical Specifications Audio Audio streaming Function/group Specifications UsersInstallation aids AudioPower Function/group Specifications InstallationMaintenance General Casing ConnectorsSoftware not Included Warranty Optional ConnectorsFunction/group Specifications Video Function Pin SpecificationsOutput Performance ConsiderationsAudio Input Axis P3367-VE Fixed Dome Network Camera M4.2
Top Page Image Contents