Axis Communications P3367VE user manual Connectors and Buttons

Page 7

AXIS P3367–VE Fixed Dome Network Camera

Hardware Overview

Connectors and Buttons

For technical specifications, see page 65.

Network Connector

RJ45 Ethernet connector with Power over Ethernet (PoE).

NOTICE

Due to local regulations or the environmental and electrical conditions in which the product is to be used, a shielded network cable (STP) may be appropriate or required. All cables connecting the product to the network and that are routed outdoors or in demanding electrical environments shall be intended for their specific use. Make sure that the network devices

are installed in accordance with the manufacturer’s instructions. For information about regulatory requirements, see Electromagnetic Compatibility (EMC) on page 2 .

I/O Connector

Use with external devices in combination with, for example, tampering alarms, motion detection, event triggering, time lapse recording and alarm notifications. In addition to the 0 V DC reference point and power (DC output), the I/O connector provides the interface to:

•Digital output – For connecting external devices such as relays and LEDs. Connected devices can be activated by the VAPIX® Application Programming Interface, output buttons on the Live View page or by an Action Rule. The output will show as active (shown under System Options > Ports & Devices) if the alarm device is activated.

•Digital input – An alarm input for connecting devices that can toggle between an open and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. When a signal is received the state changes and the input becomes active (shown under System Options > Ports & Devices).

Audio Connector

The Axis product has the following audio connectors:

•Audio in (pink) – 3.5 mm input for a mono microphone, or a line-in mono signal.

•Audio out (green) – 3.5 mm output for audio (line level) that can be connected to a public address (PA) system or an active speaker with a built-in amplifier . A stereo connector must be used for audio out.

For audio in, the left channel is used from a stereo signal.

SD Card Slot

An SD card (not included) can be used for local recording with removable storage. For more information, see Technical Specifications .

NOTICE

To prevent corruption of recordings, the SD card should be unmounted before removal. To unmount, go to Setup > System Options > Storage > SD Card and click Unmount.

Note

For SD card recommendations see www.axis.com

Control Button

The control button is used for:

•Resetting the product to factory default settings. See page 59.

•Connecting to an AXIS Video Hosting System service. See page 51. To connect, press and hold the button for about 3 seconds until the Status LED flashes green.

•Connecting to AXIS Internet Dynamic DNS Service. See page 51. To connect, press and hold the button for about 3 seconds.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Axis P3367-VE Fixed Dome Network Camera Intellectual Property Rights About this documentLegal Considerations LiabilityLearn More SupportAxis P3367-VE Fixed Dome Network Camera Table of ContentsConnectors Performance Considerations Hardware Overview Connectors and Buttons Color Indication LED IndicatorsAccess from a Browser Access the ProductStart a browser Internet Explorer, Firefox, Safari Set the Root Password Access from the InternetClick Use Https Controls on the Live View Set Power Line FrequencyConfigure Capture Mode Live ViewTo show the manual trigger buttons in the Live View Go to Setup EventsAxis Media Control viewer toolbar Manual TriggerSpeaker button Click to turn the speakers on or off PTZ ControlsMedia Streams How to Stream H.264Axis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Access Audio StreamsBasic Setup Set Up the ProductVideo Stream Video and Audio264 Click Save to apply the new settingsPixel Counter ImageCapture Mode Camera SettingsStream Profiles Wide Dynamic Range Go to Setup Video & Audio Camera SettingsImage Appearance White BalanceSet Shutter to Exposure SettingsIris adjustment Shutter & GainDay/Night Select an Aspect ratio and a Video stream resolutionView Area OverlayGo to Video & Audio Overlay Image To enable overlaysOverlay Image Go to Video & Audio Video Stream and select the Image tabGo to Events Action Rules Privacy MaskFocus & Zoom Use Overlay Text in an Action RuleAudio Input Audio SettingsWhen satisfied, click Enable iris to enable the iris Audio ModesAudio Output Audio ClipsDefault Viewer for Browsers Configure the Live ViewOutput Buttons Viewer SettingsGo to Setup Live View Config User Defined LinksAxis P3367-VE Fixed Dome Network Camera Go to PTZ Preset Positions Preset PositionsPTZ Pan Tilt Zoom To add a guard tour Guard TourAdvanced ControlsControl Queue Operator Same as administrator but with lower priorityGo to Detectors Camera Tampering DetectorsCamera Tampering Motion DetectionParameter Object Size History Sensitivity Description Set Up Motion Detection WindowsMotion Detection Parameters Go to Detectors Motion DetectionAudio Detection Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis P3367-VE Fixed Dome Network Camera Go to Events Action Rules and click Add Set Up Action RulesEvents TriggersSystem Input SignalHardware StoragePTZ Control Add RecipientsActions Recipient TypesRecipient Use with action Set Up Email RecipientsGo to Events Schedules and click Add Set Up RecurrencesCreate Schedules To create a new scheduleGo to Recordings List RecordingsFind Recordings Play RecordingGo to Recordings Continuous Export Video ClipContinuous Recording To play a recording, follow these stepsLanguages IP Address Filter System OptionsSecurity UsersCertificates IeeeGo to System Options Security Ieee Date & Time To install a self-signed certificateGo to Setup System Options Security Certificates Click Install certificate and upload the certificateNetwork Basic TCP/IP SettingsDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceUPnPTM UPnPTM can be disabled under System Options Network UPnPTMRTP/H.264 Mount and Unmount SD Card StorageBonjour SD CardGo to System Options Storage Click Network Share Under General Settings, select Autoformat toNetwork Share To add a network sharePorts & Devices MaintenanceSupport File Upload System OverviewLogs & Reports ScriptingPlain Config Reset to Factory Default SettingsCheck the Firmware TroubleshootingUpgrade the Firmware Firmware To upgrade the product’s firmwareProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsEmergency Recovery Procedure Problems setting the IP addressProblems with streaming H.264 Product is accessible locally but not externallyBasic Settings Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Setup Video & Audio Camera SettingsFocus, zoom, and fan Storage and disk management problemsTechnical Specifications Audio Function/group Specifications UsersInstallation aids Audio Audio streamingConnectors Function/group Specifications InstallationMaintenance General Casing PowerFunction Pin Specifications ConnectorsFunction/group Specifications Video Software not Included Warranty OptionalAudio Input Performance ConsiderationsOutput Axis P3367-VE Fixed Dome Network Camera M4.2
Top Page Image Contents