Axis Communications P3367VE user manual UPnPTM, RTP/H.264

Page 54

AXIS P3367–VE Fixed Dome Network Camera

System Options

SNMP

The Simple Network Management Protocol (SNMP) allows remote management of network devices. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups.

AXIS Video MIB (Management Information Base) for video hardware can be used to monitor Axis-specific, hardware-related issues that may need administrative attention. For more information about AXIS Video MIB and to download MIB files, go to www.axis.com/techsup

To enable and configure SNMP in the Axis product, go to the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

Note

All AXIS Video MIB traps are enabled when SNMP v1/v2c traps are enabled. It is not possible to turn on or off specific traps.

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 47. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 59.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video and/or Always Multicast Audio to start multicast streaming without opening an RTSP session.

54

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Axis P3367-VE Fixed Dome Network Camera Liability About this documentLegal Considerations Intellectual Property RightsSupport Learn MoreTable of Contents Axis P3367-VE Fixed Dome Network CameraConnectors Performance Considerations Hardware Overview Connectors and Buttons LED Indicators Color IndicationAccess the Product Access from a BrowserStart a browser Internet Explorer, Firefox, Safari Access from the Internet Set the Root PasswordClick Use Https Live View Set Power Line FrequencyConfigure Capture Mode Controls on the Live ViewManual Trigger Go to Setup EventsAxis Media Control viewer toolbar To show the manual trigger buttons in the Live ViewPTZ Controls Speaker button Click to turn the speakers on or offHow to Stream H.264 Media StreamsAxis Media Control AMC Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAccess Audio Streams Java applet supports simplex audio with G.711 encodingSet Up the Product Basic SetupVideo and Audio Video StreamImage Click Save to apply the new settingsPixel Counter 264Camera Settings Capture ModeStream Profiles White Balance Go to Setup Video & Audio Camera SettingsImage Appearance Wide Dynamic RangeShutter & Gain Exposure SettingsIris adjustment Set Shutter toOverlay Select an Aspect ratio and a Video stream resolutionView Area Day/NightGo to Video & Audio Video Stream and select the Image tab To enable overlaysOverlay Image Go to Video & Audio Overlay ImageUse Overlay Text in an Action Rule Privacy MaskFocus & Zoom Go to Events Action RulesAudio Modes Audio SettingsWhen satisfied, click Enable iris to enable the iris Audio InputAudio Clips Audio OutputConfigure the Live View Default Viewer for BrowsersUser Defined Links Viewer SettingsGo to Setup Live View Config Output ButtonsAxis P3367-VE Fixed Dome Network Camera Preset Positions Go to PTZ Preset PositionsPTZ Pan Tilt Zoom Controls Guard TourAdvanced To add a guard tourOperator Same as administrator but with lower priority Control QueueMotion Detection DetectorsCamera Tampering Go to Detectors Camera TamperingGo to Detectors Motion Detection Set Up Motion Detection WindowsMotion Detection Parameters Parameter Object Size History Sensitivity DescriptionAudio Detection Applications Install ApplicationGo to Setup Applications Application LicensesAxis P3367-VE Fixed Dome Network Camera Triggers Set Up Action RulesEvents Go to Events Action Rules and click AddStorage Input SignalHardware SystemRecipient Types Add RecipientsActions PTZ ControlSet Up Email Recipients Recipient Use with actionTo create a new schedule Set Up RecurrencesCreate Schedules Go to Events Schedules and click AddPlay Recording RecordingsFind Recordings Go to Recordings ListTo play a recording, follow these steps Export Video ClipContinuous Recording Go to Recordings ContinuousLanguages Users System OptionsSecurity IP Address FilterIeee CertificatesGo to System Options Security Ieee Click Install certificate and upload the certificate To install a self-signed certificateGo to Setup System Options Security Certificates Date & TimeBasic TCP/IP Settings NetworkAxis Internet Dynamic DNS Service requires IPv4 Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service DNS ConfigurationLink-Local IPv4 Address NTP ConfigurationHost Name Configuration NAT traversal port mapping for IPv4QoS Quality of Service FTPUPnPTM can be disabled under System Options Network UPnPTM UPnPTMRTP/H.264 SD Card StorageBonjour Mount and Unmount SD CardTo add a network share Under General Settings, select Autoformat toNetwork Share Go to System Options Storage Click Network ShareMaintenance Ports & DevicesSupport Scripting System OverviewLogs & Reports File UploadReset to Factory Default Settings Plain ConfigFirmware To upgrade the product’s firmware TroubleshootingUpgrade the Firmware Check the FirmwareProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsEmergency Recovery Procedure Product cannot be accessed from a browserProduct is accessible locally but not externally Problems with streaming H.264Basic Setup Video & Audio Camera Settings Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general SettingsStorage and disk management problems Focus, zoom, and fanTechnical Specifications Audio Audio streaming Function/group Specifications UsersInstallation aids AudioPower Function/group Specifications InstallationMaintenance General Casing ConnectorsSoftware not Included Warranty Optional ConnectorsFunction/group Specifications Video Function Pin SpecificationsPerformance Considerations Audio InputOutput Axis P3367-VE Fixed Dome Network Camera M4.2
Top Page Image Contents