Panasonic WV-NS324 Setup with PC, Setup with the Provided Panasonic IP Setup Software, Dns

Page 15

SETUP WITH PC

Notes:

•Do not access this menu through HTML or con- trollers during the Panasonic IP Setup procedure.

•Only one administrator is required.

■Setup with the Provided "Panasonic IP Setup" Software

Set up the network of the camera using the "Panasonic IP Setup" software included on the CD-ROM provided with the camera.

Note: If a firewall (including software) exists, allow access to all UDP ports. Otherwise, it is impossible to use the "Panasonic IP Setup" software.

In the English folder included in the Setup folder, dou- ble-click IP setup.exe.

The "Panasonic IP Setup" starts up.

The MAC address and the IP address of the connected camera will be displayed. (Click the [REFRESH] button if they are not displayed.)

1.Click the MAC address/IP address of the camera to be set up.

2.Click the [NETWORK SETUP] button.

Notes:

•When two or more cameras are connected, the MAC addresses and the IP addresses of all the connected cameras will be displayed.

•The "Panasonic IP Setup" software can recog- nize only those cameras in the same subnet.

•Pressing the [REFRESH] button will display the updated MAC addresses and IP addresses of all the connected cameras that are in the same subnet.

The setup window appears.

3.Set parameters for each item. "IP Address"

"Subnet Mask" "Default Gateway" "HTTP Port"

4.Input the parameters for your environment. "DHCP"

"DNS"

5.Click the [Enable] button when using DHCP and DNS.

When using the DHCP and DNS functions, enter the "Primary DNS Server address" and the "Secondary DNS Server address".

6.Click [AUTO] when the DNS server gets primary and secondary IP addresses from the DHCP serv- er.

Notes:

•If DHCP is enabled although there is no DHCP server in the network, check "Disable" for DHCP in the "Panasonic IP Setup" window.

•If DHCP is enabled, and the DHCP server has not assigned an IP address yet, "0.0.0.0" is dis- played for the IP address. The IP address of the camera will be displayed after the DHCP server assigns one to the camera.

7.Click the [SET] button after completing the setting.

Important: It takes around 10 seconds for settings to take effect after the [SET] button has been pressed. The settings may be performed incorrect- ly if the power is off or the Ethernet cable is detached before the settings are completed.

Note: Do not make any other settings while executing Panasonic IP Setup.

-15-

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Operating Instructions English Version Important Safety Instructions Contents Trademarks FeaturesPreface System RequirementsCamera Cleaning Preset Data Uploading or DownloadingDocument Convention Precautions Construction Assemble the Camera InstallationSetting Switches Disassembling the CameraTop Cable Exit Cutout in Decoration CoverTop Cable Exit Connections AC Power Supply ConnectionHow to Assemble the Cable with the Accessory Connector Connect this to 24V AC Class 2 Power Supply onlyNetwork Connections Connection to Internet Type NecessariesSetup with PC Setup with the Provided Panasonic IP Setup SoftwareDNS Preparations for the PC Network Setup of Your PCNetwork Setup of the Camera Page Ddns Network Setup Parameters vs. Connection TypeConnection type Parameter description DhcpDhcp server assigns an IP address to the camera automatical Preliminary Setup Ddns Dynamic DNS Consult your system administrator Camera Control Access from the PCOperating the Camera Multi Screen SelectAccess from a System Device Function Comparison / PC Network vs. Camera site PAN/TILT ZOOM/FOCUS Iris Preset Auto PANFrom the PC Prior to SetupButtons Used for Setup Menus Camera Setup MenusSetup Menu SetupFocus Switch Setting Procedures PresettingMenu Display Position Setting Position SET To Set Panning/Tilting PositionsTo Set the Lens Zoom and Focus Positions Preset Identification Setting Preset ID To Return to the Preset Number Set Menu Deleting Preset PositionsLight Control Setting ALC/MANUAL Auto Focus Setting AF ModeOFF Auto PAN Home Position Setting HomeSelf-return Setting Self Return Auto Mode Selection Auto ModeAuto 30S 20S 10S Flip-A-Chip SettingCleaning Cleaning Image Hold Image HoldTo Enter a New Camera ID Camera SettingTo Display the Camera Setting Menu Camera Identification Camera IDALC Mode with BLC OFF ALC Mode with BLC onSynchronization Sync Shutter Speed Setting ShutterLine-lock Sync Mode LL Gain Control AGCWhite Balance White BAL Auto-Tracing White Balance Mode ATWElectronic Zoom EL-ZOOM Automatic White Balance Control Mode AWCElectronic Sensitivity Enhancement Sens UP Motion Detector Motion DETX4 FIX X2 FIX OFF Demonstration Display Demo Mode Special Menu SpecialDigital Noise Reduction DNR To Close the Special Menu To Restore the Camera Default Position RefreshCamera Resetting Camera Reset Reset to the Factory Default SettingsCamera Setup with PC Setup from PC Image SetupAlarm Setup FTP Client Setup User Setup Host Setup System Setup Multiscreen Setup Auto Pan Setting Preset SetupSetting the Switches Common proceduresInitializing Still Picture Storage to the PC Viewing PicturesWhen alarm arises Alarm FunctionsTransferring Picture Files Canceling Alarm DisplayVMD Setup Detection Area SetupPage Reviewing Alarm Pictures Substitution Letter Description indication type etc Resetting AlarmHow to customize contents of e-mail notification StepUser Name admin Password None Step Auxiliary Output Control Auxiliary Output ControlTroubleshooting Camera Section SpecificationsPrevention of Blooming and Smear Network SectionAccessories Optional AccessoriesLens/Mechanism sections Appendix Panasonic Digital Communications & Security Company
Top Page Image Contents