Panasonic WV-NS324 operating instructions Auto

Page 34

3.Panning starting point and panning endpoint Follow the steps below.

(1)Move the cursor to POSITION and press the CAM (SET) key. The cursor moves to START.

** AUTO

PAN **

 

 

START

 

POSITION

 

 

 

 

END

 

SPEED

••••••••

 

 

L

H

PAN LIMIT

OFF

 

ENDLESS

OFF

 

DWELL TIME

2S

 

RET

 

 

 

** AUTO

PAN **

 

POSITION

 

 

START

 

 

 

 

END

 

SPEED

••••••••

 

 

L

H

PAN LIMIT

OFF

 

ENDLESS

OFF

 

DWELL TIME

2S

 

RET

(2)Move the joystick to the right or left to select a panning starting point and press the CAM (SET) key.

This determines the starting point and the cur- sor moves to END.

** AUTO

PAN **

 

POSITION

START

 

SPEED

END

••••

••••

 

L

H

PAN LIMIT

OFF

 

ENDLESS

OFF

 

DWELL TIME

2S

 

RET

(3)Move the joystick to the right or left to select a panning endpoint and press the CAM (SET) key.

This determines the endpoint, and the cursor moves to POSITION.

4.Panning speed

The panning speed increases when the joystick is moved to the right, and decreases when it is moved to the left.

** AUTO PAN **

POSITION START

END

SPEED ••••••••

L H

PAN LIMIT OFF

ENDLESS OFF

DWELL TIME 2S

RET

Notes:

If the panning range is changed after the camera has not panned for a long time or has been pan- ning in the same panning range, the picture may not be clear or noise may appear. In this case, pan the camera fully several times.

If this does not eliminate the problem, refer servic- ing to qualified service personnel.

When you press the CAM (SET) key, the camera might move slightly to memorize the nearest pan- ning/tilting position.

5.Pan limit ON/OFF

The factory default setting is OFF.

ON: Manual pan is limited from the starting point to the endpoint specified by position setting. Set ENDLESS to OFF before setting PAN LIMIT to ON.

OFF: Manual pan is not limited.

Endpoint

 

Start-end

Camera

Self-end

range of

range of

auto pan

pan limit

Starting point

Note: When ON is selected for PAN LIMIT, manual pan moves the camera away from the other side (PAN LIMIT) of the start-end range.

6.ENDLESS to ON/OFF

The factory default setting is OFF.

ON: The camera pans from the starting point to the endpoint, and keeps rotating in the same direction to return to the starting point. Set PAN LIMIT to OFF before setting ENDLESS to ON.

** AUTO PAN **

 

POSITION

START

 

 

END

 

SPEED

••••••••

 

L

H

PAN LIMIT

OFF

 

ENDLESS

ON

 

 

DWELL TIME

2S

 

 

RET

OFF: The camera pans from the starting point to the endpoint, and rotates backward to the starting point.

This movement is repeated over and over.

7.Dwell time

The factory default setting is 2S. Dwell time changes as follows:

-35-

Image 34
Contents Operating Instructions English Version Important Safety Instructions Contents System Requirements FeaturesPreface TrademarksPreset Data Uploading or Downloading Camera CleaningDocument Convention Precautions Construction Disassembling the Camera InstallationSetting Switches Assemble the CameraCutout in Decoration Cover Top Cable ExitTop Cable Exit Connect this to 24V AC Class 2 Power Supply only AC Power Supply ConnectionHow to Assemble the Cable with the Accessory Connector ConnectionsNetwork Connections Necessaries Connection to Internet TypeSetup with the Provided Panasonic IP Setup Software Setup with PCDNS Network Setup of Your PC Preparations for the PCNetwork Setup of the Camera Page Dhcp Network Setup Parameters vs. Connection TypeConnection type Parameter description DdnsDhcp server assigns an IP address to the camera automatical Preliminary Setup Ddns Dynamic DNS Consult your system administrator Multi Screen Select Access from the PCOperating the Camera Camera ControlAccess from a System Device PAN/TILT ZOOM/FOCUS Iris Preset Auto PAN Function Comparison / PC Network vs. Camera siteCamera Setup Menus Prior to SetupButtons Used for Setup Menus From the PCSetup Setup MenuFocus Switch Presetting Setting ProceduresMenu Display To Set Panning/Tilting Positions Position Setting Position SETTo Set the Lens Zoom and Focus Positions Preset Identification Setting Preset ID Auto Focus Setting AF Mode Deleting Preset PositionsLight Control Setting ALC/MANUAL To Return to the Preset Number Set MenuAuto Mode Selection Auto Mode Home Position Setting HomeSelf-return Setting Self Return OFF Auto PANAuto Image Hold Image Hold Flip-A-Chip SettingCleaning Cleaning 30S 20S 10SCamera Identification Camera ID Camera SettingTo Display the Camera Setting Menu To Enter a New Camera IDALC Mode with BLC on ALC Mode with BLC OFFGain Control AGC Shutter Speed Setting ShutterLine-lock Sync Mode LL Synchronization SyncAuto-Tracing White Balance Mode ATW White Balance White BALAutomatic White Balance Control Mode AWC Electronic Zoom EL-ZOOMMotion Detector Motion DET Electronic Sensitivity Enhancement Sens UPX4 FIX X2 FIX OFF Special Menu Special Demonstration Display Demo ModeDigital Noise Reduction DNR Reset to the Factory Default Settings To Restore the Camera Default Position RefreshCamera Resetting Camera Reset To Close the Special MenuCamera Setup with PC Image Setup Setup from PCAlarm Setup FTP Client Setup User Setup Host Setup System Setup Multiscreen Setup Preset Setup Auto Pan SettingCommon procedures Setting the SwitchesInitializing Viewing Pictures Still Picture Storage to the PCAlarm Functions When alarm arisesDetection Area Setup Canceling Alarm DisplayVMD Setup Transferring Picture FilesPage Reviewing Alarm Pictures Step Resetting AlarmHow to customize contents of e-mail notification Substitution Letter Description indication type etcUser Name admin Password None Step Auxiliary Output Control Auxiliary Output ControlTroubleshooting Network Section SpecificationsPrevention of Blooming and Smear Camera SectionOptional Accessories AccessoriesLens/Mechanism sections Appendix Panasonic Digital Communications & Security Company