Panasonic WV-NS324 To Restore the Camera Default Position Refresh, Camera Resetting Camera Reset

Page 43

(7)To Restore the Camera Default Position (REFRESH)

Move the cursor to REFRESH by using the joystick and press the [F2] button of the WV-CU550CJ.

For the WV-RM70, WV-CU360CJ or WV-CU161C, keep pressing the Right and Left switches simulta- neously for 2 seconds or more.

** SPECIAL **

CHROMA GAIN	••••••••
AP GAIN	••••••••
PEDESTAL	••••••••
HUE	•I•••••••
	–	+

DNR	LOW
DEMO MODE	OFF
REFRESH	→PUSH SET
CAMERA RESET	→PUSH SET
RET

(8)Camera Resetting (CAMERA RESET)

Move the cursor to CAMERA RESET by using the joystick and press the [F3] button of the WV- CU550CJ.

The camera is reset to the factory settings.

For the WV-RM70, keep pressing the Right, Left and Set switches simultaneously for 2 seconds or more. For the WV-CU360CJ or WV-CU161C, keep pressing the Right and Left switches and the numeric button 5 simultaneously for 2 seconds or more.

** SPECIAL **

CHROMA GAIN	••••••••
AP GAIN	••••••••
PEDESTAL	••••••••
HUE	•I•••••••
	–	+

DNR	LOW
DEMO MODE	OFF
REFRESH	→PUSH SET
CAMERA RESET	→PUSH SET
RET

(9)To Close the SPECIAL Menu

Move the cursor to RET and press the CAM (SET) key.

The setup menu appears on the monitor screen.

** SPECIAL **

CHROMA GAIN	••••••••
AP GAIN	••••••••
PEDESTAL	••••••••
HUE	•I•••••••
	–	+

DNR		LOW
DEMO MODE		OFF
REFRESH		→PUSH SET
CAMERA RESET		→PUSH SET
RET

Reset to the Factory Default Settings

Any of the above settings plus the ALC/MANUAL level control and phase adjustments can be reset to the fac- tory default settings by placing the cursor over the desired mode and then pressing the [F2] button of the WV-CU550CJ. For the WV-RM70, keep pressing the Right and Left switches simultaneously for 2 seconds or more.

-44-

Image 43

Contents Operating Instructions English Version Important Safety Instructions Contents Trademarks FeaturesPreface System RequirementsPreset Data Uploading or Downloading Camera CleaningDocument Convention Precautions Construction Assemble the Camera InstallationSetting Switches Disassembling the CameraTop Cable Exit Cutout in Decoration CoverTop Cable Exit Connections AC Power Supply ConnectionHow to Assemble the Cable with the Accessory Connector Connect this to 24V AC Class 2 Power Supply onlyNetwork Connections Connection to Internet Type NecessariesSetup with the Provided Panasonic IP Setup Software Setup with PCDNS Preparations for the PC Network Setup of Your PCNetwork Setup of the Camera Page Ddns Network Setup Parameters vs. Connection TypeConnection type Parameter description DhcpDhcp server assigns an IP address to the camera automatical Preliminary Setup Ddns Dynamic DNS Consult your system administrator Camera Control Access from the PCOperating the Camera Multi Screen SelectAccess from a System Device Function Comparison / PC Network vs. Camera site PAN/TILT ZOOM/FOCUS Iris Preset Auto PANFrom the PC Prior to SetupButtons Used for Setup Menus Camera Setup MenusSetup Menu SetupFocus Switch Presetting Setting ProceduresMenu Display To Set Panning/Tilting Positions Position Setting Position SETTo Set the Lens Zoom and Focus Positions Preset Identification Setting Preset ID To Return to the Preset Number Set Menu Deleting Preset PositionsLight Control Setting ALC/MANUAL Auto Focus Setting AF ModeOFF Auto PAN Home Position Setting HomeSelf-return Setting Self Return Auto Mode Selection Auto ModeAuto 30S 20S 10S Flip-A-Chip SettingCleaning Cleaning Image Hold Image HoldTo Enter a New Camera ID Camera SettingTo Display the Camera Setting Menu Camera Identification Camera IDALC Mode with BLC OFF ALC Mode with BLC onSynchronization Sync Shutter Speed Setting ShutterLine-lock Sync Mode LL Gain Control AGCWhite Balance White BAL Auto-Tracing White Balance Mode ATWElectronic Zoom EL-ZOOM Automatic White Balance Control Mode AWCMotion Detector Motion DET Electronic Sensitivity Enhancement Sens UPX4 FIX X2 FIX OFF Special Menu Special Demonstration Display Demo ModeDigital Noise Reduction DNR To Close the Special Menu To Restore the Camera Default Position RefreshCamera Resetting Camera Reset Reset to the Factory Default SettingsCamera Setup with PC Image Setup Setup from PCAlarm Setup FTP Client Setup User Setup Host Setup System Setup Multiscreen Setup Auto Pan Setting Preset SetupCommon procedures Setting the SwitchesInitializing Still Picture Storage to the PC Viewing PicturesWhen alarm arises Alarm FunctionsTransferring Picture Files Canceling Alarm DisplayVMD Setup Detection Area SetupPage Reviewing Alarm Pictures Substitution Letter Description indication type etc Resetting AlarmHow to customize contents of e-mail notification StepUser Name admin Password None Step Auxiliary Output Control Auxiliary Output ControlTroubleshooting Camera Section SpecificationsPrevention of Blooming and Smear Network SectionOptional Accessories AccessoriesLens/Mechanism sections Appendix Panasonic Digital Communications & Security Company