Panasonic WV-NS324 operating instructions ALC Mode with BLC on, ALC Mode with BLC OFF

Page 37

(1)ALC Mode with BLC ON

In normal use, the important object in a scene is placed in the centre of the monitor screen. When set at the factory, more photometric weight is given to the centre of the screen than to the edge of the screen (where bright backlight would most likely be located). In such a case, the object at the centre of the screen can be still clearly seen even though the backlight may vary.

1.Press the CAM (SET) key after selecting ALC. The ALC CONT menu appears.

2.Move the cursor to the BLC and select ON.

** ALC CONT **

BACK LIGHT COMP

BLC		OFF
MASK SET
LEVEL		•••••••
		-			+
RET
ALC CONT
BACK LIGHT COMP
BLC
BLC		ON
LEVEL		•••••••
		-			+

RET

3.If you want to adjust the video output level, move the "I" cursor for LEVEL. Adjust it to the desired level by using the joystick.

4.Move the cursor to RET and press the CAM (SET) key to return to the CAM SET UP menu. To return to the camera picture, press the [F4] button.

(2)ALC Mode with BLC OFF

This mode is effective when the main object in the scene is not located in the centre of the screen but a source of bright light is located near the centre of the scene. In this mode, the picture is divided into 48 areas that mask the light to keep the clarity of the picture.

Note: The result of field setup of the mask area and level adjustment is fed back (effected) to the lens iris control in ALC mode.

1.Move the cursor to the BLC and select OFF. When you select MANUAL, BLC is not avail- able. MASK SET appears on the menu.

2.Move the cursor to MASK SET and press the CAM (SET) key. The 48 mask areas appear on the monitor screen. The cursor is blinking in the top left corner of the screen.

Blinking

3.To mask an area where backlight is bright, move the cursor to the area and press the CAM (SET) key. The mask turns to white. Repeat this procedure to mask the desired area.

Blinking

Turns to white

Blinking

4.To cancel a masked area, move the cursor to the area, and press the CAM (SET) key. To cancel all masked areas, press the [F2] button of the WV-CU550CJ. For the WV-RM70, press the right and left switches simultaneously.

5.After masking is completed, press the MON (ESC) key. The 48 mask areas on the monitor screen disappear and the ALC CONT menu appears.

-38-

Image 37

Contents Operating Instructions English Version Important Safety Instructions Contents Preface FeaturesSystem Requirements TrademarksPreset Data Uploading or Downloading Camera CleaningDocument Convention Precautions Construction Setting Switches InstallationDisassembling the Camera Assemble the CameraTop Cable Exit Cutout in Decoration CoverTop Cable Exit How to Assemble the Cable with the Accessory Connector AC Power Supply ConnectionConnect this to 24V AC Class 2 Power Supply only ConnectionsNetwork Connections Connection to Internet Type NecessariesSetup with the Provided Panasonic IP Setup Software Setup with PCDNS Preparations for the PC Network Setup of Your PCNetwork Setup of the Camera Page Connection type Parameter description Network Setup Parameters vs. Connection TypeDhcp DdnsDhcp server assigns an IP address to the camera automatical Preliminary Setup Ddns Dynamic DNS Consult your system administrator Operating the Camera Access from the PCMulti Screen Select Camera ControlAccess from a System Device Function Comparison / PC Network vs. Camera site PAN/TILT ZOOM/FOCUS Iris Preset Auto PANButtons Used for Setup Menus Prior to SetupCamera Setup Menus From the PCSetup Menu SetupFocus Switch Presetting Setting ProceduresMenu Display To Set Panning/Tilting Positions Position Setting Position SETTo Set the Lens Zoom and Focus Positions Preset Identification Setting Preset ID Light Control Setting ALC/MANUAL Deleting Preset PositionsAuto Focus Setting AF Mode To Return to the Preset Number Set MenuSelf-return Setting Self Return Home Position Setting HomeAuto Mode Selection Auto Mode OFF Auto PANAuto Cleaning Cleaning Flip-A-Chip SettingImage Hold Image Hold 30S 20S 10STo Display the Camera Setting Menu Camera SettingCamera Identification Camera ID To Enter a New Camera IDALC Mode with BLC OFF ALC Mode with BLC onLine-lock Sync Mode LL Shutter Speed Setting ShutterGain Control AGC Synchronization SyncWhite Balance White BAL Auto-Tracing White Balance Mode ATWElectronic Zoom EL-ZOOM Automatic White Balance Control Mode AWCMotion Detector Motion DET Electronic Sensitivity Enhancement Sens UPX4 FIX X2 FIX OFF Special Menu Special Demonstration Display Demo ModeDigital Noise Reduction DNR Camera Resetting Camera Reset To Restore the Camera Default Position RefreshReset to the Factory Default Settings To Close the Special MenuCamera Setup with PC Image Setup Setup from PCAlarm Setup FTP Client Setup User Setup Host Setup System Setup Multiscreen Setup Auto Pan Setting Preset SetupCommon procedures Setting the SwitchesInitializing Still Picture Storage to the PC Viewing PicturesWhen alarm arises Alarm FunctionsVMD Setup Canceling Alarm DisplayDetection Area Setup Transferring Picture FilesPage Reviewing Alarm Pictures How to customize contents of e-mail notification Resetting AlarmStep Substitution Letter Description indication type etcUser Name admin Password None Step Auxiliary Output Control Auxiliary Output ControlTroubleshooting Prevention of Blooming and Smear SpecificationsNetwork Section Camera SectionOptional Accessories AccessoriesLens/Mechanism sections Appendix Panasonic Digital Communications & Security Company