Panasonic WV-NS324 operating instructions Initializing, Setting the Switches, Common procedures

Page 51

INITIALIZING

You can reset the following data to the factory default settings.

Camera Setup HTML files

Setting the Switches

The camera is provided with an 8-bit DIP switch. The 8- bit DIP switch is used to return the camera to the facto- ry default settings. Switch settings are read into the camera when the power is turned on. Make sure to turn the camera off, then turn it back on after changing the switch settings. Switch positions and functions are shown below.

Note: All DIP switches except SW1 and SW2 should always be set to "off".

Menus: Initializing Setup menu Initializing HTML files

Initializing Setup menu and HTML files

No.	DIP	DIP	Status			Dip SW
No.	SW1	SW2	Status			Position

							8-bit DIP SW
1	OFF	OFF	Normal			Normal Position
1	OFF	OFF	Normal		ON
					1	2	3	4	5	6	7	8


2	ON	OFF	Initializing the setup menu		ON
2	ON	OFF	Initializing the setup menu		1	2	3	4	5	6	7	8
					1	2	3	4	5	6	7	8


3	OFF	ON	Initializing HTML files		ON
3	OFF	ON	Initializing HTML files		1	2	3	4	5	6	7	8
					1	2	3	4	5	6	7	8

			Initializing the setup menu
4	ON	ON	Initializing the setup menu		ON
			& HTML files		1	2	3	4	5	6	7	8

Common procedures:

1.Set DIP SW1 and SW2 in accordance with the table.

2.Turn the power on, and wait until the servo initial- ization of Camera is completed.

3.Turn the power off, and return the DIP switch to normal position.

Note: Do not make any DIP switch setting other than above.

-52-

Image 51

Contents Operating Instructions English Version Important Safety Instructions Contents Trademarks FeaturesPreface System RequirementsCamera Cleaning Preset Data Uploading or DownloadingDocument Convention Precautions Construction Assemble the Camera InstallationSetting Switches Disassembling the CameraTop Cable Exit Cutout in Decoration CoverTop Cable Exit Connections AC Power Supply ConnectionHow to Assemble the Cable with the Accessory Connector Connect this to 24V AC Class 2 Power Supply onlyNetwork Connections Connection to Internet Type NecessariesSetup with PC Setup with the Provided Panasonic IP Setup SoftwareDNS Preparations for the PC Network Setup of Your PCNetwork Setup of the Camera Page Ddns Network Setup Parameters vs. Connection TypeConnection type Parameter description DhcpDhcp server assigns an IP address to the camera automatical Preliminary Setup Ddns Dynamic DNS Consult your system administrator Camera Control Access from the PCOperating the Camera Multi Screen SelectAccess from a System Device Function Comparison / PC Network vs. Camera site PAN/TILT ZOOM/FOCUS Iris Preset Auto PANFrom the PC Prior to SetupButtons Used for Setup Menus Camera Setup MenusSetup Menu SetupFocus Switch Setting Procedures PresettingMenu Display Position Setting Position SET To Set Panning/Tilting PositionsTo Set the Lens Zoom and Focus Positions Preset Identification Setting Preset ID To Return to the Preset Number Set Menu Deleting Preset PositionsLight Control Setting ALC/MANUAL Auto Focus Setting AF ModeOFF Auto PAN Home Position Setting HomeSelf-return Setting Self Return Auto Mode Selection Auto ModeAuto 30S 20S 10S Flip-A-Chip SettingCleaning Cleaning Image Hold Image HoldTo Enter a New Camera ID Camera SettingTo Display the Camera Setting Menu Camera Identification Camera IDALC Mode with BLC OFF ALC Mode with BLC onSynchronization Sync Shutter Speed Setting ShutterLine-lock Sync Mode LL Gain Control AGCWhite Balance White BAL Auto-Tracing White Balance Mode ATWElectronic Zoom EL-ZOOM Automatic White Balance Control Mode AWCElectronic Sensitivity Enhancement Sens UP Motion Detector Motion DETX4 FIX X2 FIX OFF Demonstration Display Demo Mode Special Menu SpecialDigital Noise Reduction DNR To Close the Special Menu To Restore the Camera Default Position RefreshCamera Resetting Camera Reset Reset to the Factory Default SettingsCamera Setup with PC Setup from PC Image SetupAlarm Setup FTP Client Setup User Setup Host Setup System Setup Multiscreen Setup Auto Pan Setting Preset SetupSetting the Switches Common proceduresInitializing Still Picture Storage to the PC Viewing PicturesWhen alarm arises Alarm FunctionsTransferring Picture Files Canceling Alarm DisplayVMD Setup Detection Area SetupPage Reviewing Alarm Pictures Substitution Letter Description indication type etc Resetting AlarmHow to customize contents of e-mail notification StepUser Name admin Password None Step Auxiliary Output Control Auxiliary Output ControlTroubleshooting Camera Section SpecificationsPrevention of Blooming and Smear Network SectionAccessories Optional AccessoriesLens/Mechanism sections Appendix Panasonic Digital Communications & Security Company