Panasonic GP-US532HA Gamma Correction Gamma, Auto Knee ON/OFF Auto Knee, Chroma Matrix Controls

Page 21

8-1. Gamma Correction (GAMMA)

1.Move the cursor to the GAMMA parameter. The “I” cur- sor starts blinking.

2.While observing the waveform monitor or the color video monitor, adjust the gamma level.

When the “I” cursor is at the end of the “+” side,

gamma correction is set to OFF.

When the “I” cursor is at the end of the “− ” side, black strech (BLACK STRET) is set.

8-2. Auto Knee ON/OFF (AUTO KNEE)

1.Move the cursor to the AUTO KNEE parameter.

2.Select ON or OFF for the auto knee mode.

8-3. Total Pedestal Level Control (TOTAL-PED)

1.Move the cursor to the TOTAL-PED parameter. The “I” cursor starts blinking.

2.While observing the waveform monitor or the color video monitor, adjust the total pedestal level (black level).

Move the “I” cursor to the “+” side to make the image

brighter.

Move the “I” cursor to the “− ” side to make the image darker.

8-4. Chrominance Level Control (CHROMA GAIN)

1.Move the cursor to the CHROMA GAIN parameter. The “I” cursor starts blinking.

2.While observing the waveform monitor or the color video monitor, adjust the chroma level.

8-5. Detail Band Control (DTL BAND)

1.Move the cursor to the DTL BAND parameter. The “I” cursor starts blinking.

2.While observing the color video monitor, adjust the aperture level.

Move the “I” cursor to the “+” side to raise the frequen-

cy.

Move the “I” cursor to the “− ” side to lower the frequen- cy.

8-6. Horizontal Detail Gain Control (HDTL GAIN)

1.Move the cursor to the HDTL GAIN parameter. The “I” cursor starts blinking.

2.While observing the color video monitor, adjust the aperture level.

Move the “I” cursor to the “+” side to make the image

sharper.

Move the “I” cursor to the “− ” side to make the image

softer.

When the “I” cursor is at the end of the “− ” side, the horizontal detail level is set to OFF.

8-7. Vertical Detail Gain Control (VDTL GAIN)

1.Move the cursor to the VDTL GAIN parameter. The “I” cursor starts blinking.

2.While observing the color video monitor, adjust the aperture level.

Move the “I” cursor to the “+” side to make the image

sharper.

Move the “I” cursor to the “− ” side to make the image

softer.

When the “I” cursor is at the end of the “− ” side, the vertical detail level is set to OFF.

8-8. Red Detail ON/OFF (RED DTL)

1.Move the cursor to the RED DTL parameter.

2.Select ON or OFF for the RED DTL mode.

When ON is selected, the red detail is enhanced.

8-9. Clear Digital Noise Reduction Control (CLEAN DNR)

1.Move the cursor to the CLEAN DNR parameter.

2.Select OFF, LOW or HI for the CLEAN DNR mode.

8-10. 2 Dimention Low Pass Filter (2D LPF)

1.

Move the cursor to the 2D LPF parameter.

2.

Select ON or OFF for the 2D LPF mode.

8-11. 6 Chroma Matrix Controls

(MATRIX R-G) (MATRIX R-B) (MATRIX G-R) (MATRIX G-B) (MATRIX B-R) (MATRIX B-G)

1.Move the cursor to the desired matrix item. The “I” cur- sor starts blinking.

2.While observing the vectorscope or the color video monitor, adjust the matrix level.

8-12. Chroma Phase Control (HUE)

1.Move the cursor to the HUE parameter. The “I” cursor starts blinking.

2.While observing the vectorscope or the color video monitor, adjust the chroma phase (hue).

To reset to the factory setting

Any of the above settings except AUTO KNEE, RED DTL, CLEAN DNR and 2D LPF, can be reset to the factory set- tings.

Move the cursor to the desired item and press A and B simultaneously for a second and more.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents GP-US532HA Contents Preface FeaturesClean the faceplate with care PrecautionsPut the lens cap on the camera after using the camera Ask a qualified service person for installationPower Indicator Power Camera Cable ConnectorLens Mount Camera Mounting Screw HoleTitle Input Connector Title Auto Warning IndicatorCamera/Color Bar Selector CAM/BAR White Balance Selector ATW/AWC/MANUGen-lock Signal Input Connector VBS/HD Camera Cable Connector CameraExternal HD and VD Mode Gen-Lock Signal Input Connector VDRGB/SYNC Output Connector RGB/SYNC Video Output Connector S-VIDEO OUTRS-232C Connector RS-232C DC Input Terminals 12V DCInternal Sync Operation ConnectionsLens Mount Mounting the LensItem Button Item SetupThis button is used to move the cursor downwards Left Button aEditing the Setup menu Opening the Setup menuAll Reset Operation Press the page button for a few secondsSetting Procedures Field/Frame Charging Mode Setting FLD/FRMCamera Identification Camera ID ELC detection control area setting ELC Electronic Light Control Setting ELCPeak and Average Weight Control PEAK/AVE Manual setting of the ELC detection control area ManuElectronic Shutter Speed Setting Shutter Gain Control Setting GainAGC detection control area setting AGC Internal Sync Mode INT Synchronization Setting SyncVBS Gen-lock Mode Extvbs Maximum +9 dBSubcarrier Coarse Phase Adjustment SC Coarse Horizontal Phase Adjustment H PhaseSubcarrier Fine Phase Adjustment SC Fine VS Gen-lock Mode ExtvsExternal HD/VD Mode HD/VD Black Balance Setting Black BALExternal VD Mode VD Auto Black Balance Setting Black BALScene File Setting Scene File Returning to the Setup menuTo turn Chroma Phase Control HUE Clear Digital Noise Reduction Control Clean DNRTo reset to the factory setting Gamma Correction GammaPrevention of Blooming and Smear Specifications GP-CA522/4 Optional AccessoriesCharacter Generators Division of Matsushita Electric Corporation of America
Top Page Image Contents