Canon VB150 appendix Webview Livescope Settings

Page 55

Detail Settings

Webview Livescope Settings Page

Use this page to specify settings for WebView Livescope.

"Restrict Service Time"

When you want to set video distribution time for the viewers (→ P.6), tick this option and specify the Start and End times.

The Admin Viewer can be used to display video at times other than the time specified. (→ P.92)

e

● If you want to restrict video service time, use

"Restrict Service Time".

Tip

● The “Maximum Frame Rate” and “Maximum

 

 

number of Clients” settings are useful in

 

limiting the volume of network traffic.

 

 

WebView Livescope

"Video Transmission Port"

Sets the TCP port number for the video transmission protocol. Enter a value between 1 and 65535. The default setting is 65310. Normally, there is no need to change this setting.

"Camera Control Port"

Sets the TCP port number for the camera control protocol. Enter a value between 1 and 65535. The default setting is 65311. Normally, there is no need to change this setting.

"Maximum Number of Clients"

Sets the maximum number of clients that can be connected simultaneously from the viewers (→ P.6). Enter a value from 1 to 50.

"Control Queue Length"

Sets the length of the queue when multiple clients are waiting for control privileges under the viewer.

Enter a value between 0 and 50. The maximum number is 50. When set to "0", only the Admin Viewer is permitted to control the camera.

"Maximum Frame Rate (fps)"

Sets the maximum number of frames captured per second. The maximum frame rate is 30.0 fps and enter a number between 0.1 and 30.0.

"Maximum View Time (sec)"

Sets the maximum time the client can view video using the viewer. Enter a value between 0 and 65535. A setting of 0 disables the time limitation.

"Maximum Camera Control Time (sec)" Sets the maximum time for which camera control privileges can be maintained under the viewer. Enter a value between 1 and 3600.

"Camera Stabilization Time"

When the GetStillImage command (dGuide to Creating Web Pages for Video Distribution P.21) has been requested, this setting specifies the delay to allow the camera to stabilize before a still picture is captured. Enter a value between 0 and 10000. The maximum delay is 10000 milliseconds.

3

Detail Settings

Click the [OK] button to change the settings. To discard the changes, click the

[Cancel] button. This returns you to the settings title page.

54

Page 54 Page 56
Image 55
Page 54 Page 56
Contents VB150 Trademark Notices IntroductionExclusion of Liability Copyright InformationChecking the Package Contents Contents 107 101103 104Introduction Viewer for PC SettingsUsing the Still Picture Recording Function Using the Motion Detection FunctionViewer Software How to Read This ManualThis document Picture Recording User’s Guide Guide to Creating Web Pages for Video DistributionImportant Warnings Safe Use of EquipmentImportant Operational Instructions FCC Notice Important Safety Instructions Safe Use of Equipment Page Cleaning the Equipment MaintenancePage Before Using the VB150 WebView Livescope built Compatible with wireless LANsPanorama picture creation function and various settings Camera position preset functionPlenty of expandability Easy setting and administrationView restriction function Built-in Web server and FTP serverVideo Distributor System OverviewViewer Software Supplied Viewer for Java Ver VB Administration Tools Ver .1 → P.59Operating Environment VBCollector Ver .1 → dPicture Recording User’s Guide P.13Compatible PC Cards Sold separately Viewer Software for Monitoring Use Sold separatelyCompatible Cameras Sold separately Compatible NetworksSystem Components and Their Operation PC card slot B Factory defaults reset switch100/10 BT Ethernet connector Camera control connector CC1, CC2Page Setting Up the VB150 Connecting the camera Setup WorkflowChecking operation Camera connection is now complete Connecting the cameraInitializing the VB150 Precautions for Turning the VB150 On and OffClick to select Initial settings are now complete Example of Viewer for Java Checking operationOperation checking is now complete We recommend that you create a panorama picture → P.65Detail Settings Accessing the Settings Title Detail SettingsSettings Title Parallel Settings TitleOthers System SettingsAdministration Account Settings Web page URLEthernet Network SettingsConnections Installation location and communications securityWireless LAN With the new IP address → P.34PPP Primarily CallPPPConnection Keeping Static Route ControlCommon Settings Camera and Video SettingsSettings for cameras 1 to View Restriction Example of 2 cameras cascade Connected to 1 camera control connectorConnected to 2 camera control connectors Example of 4 cameras cascadeControllable Range and Video Capture Range for Each Camera View Restriction SettingsTouching it, be sure to reboot the VB150. → P.57 Controllable Range and Video Capture RangeAbout View Restriction Web Pages for Video Distribution P.9 Preset SettingsCommon Setting Presets Up to 8 presets can be specified→dPicture Recording Users Guide P.13 Picture Recording and External Device I/O SettingsPicture Recording Common Settings Start up the Viewer for PC then check the Size valueDescription Values Specifying parameters in Picture Mail messagesControl based on motion detection Use the Motion Detection Setting Tool → P.80External Device Common Settings For picture recording and external devicePicture Recording Triggered by External Devices Picture Recording and Output by Method varies with the environment being usedBeen reached ExampleUsers can be registered Access Control SettingsAuthorized/Restricted Host Specification → P.52 Authorized User Account → P.52Listing Guidelines Example 1 To prohibit access from a hostAuthorized/Restricted Host List Descriptions Listing FormatPage Webview Livescope Settings Mail Miscellaneous SettingsHttp Server Log.0... are created Flash memory card is inserted into the slot on the VB150Log Slot A/B Administration Tools SettingsMiscellaneous On-board File System InformationVB Administration Tools VBAdmin Startup Panel → P.63 Overview of VB Administration ToolsPanorama Creation Tool → P.65 View Restriction Tool → P.70 Preset Setting Tool → P.75Motion Detection Setting Tool → P.80 Admin Viewer → P.92Be installed → P.19 Installing VB Administration ToolsTo Install WebView Livescope Manager VB Administration Tools Ver.1.0WebView Livescope Helper Viewer Ver .1 or earlier WebView Livescope Camera ServerTo Start Up Starting Up VB Administration ToolsViewer and Admin Viewer can be started up at the same time Without a panorama picture Panorama Creation ToolWith a panorama picture Panorama shot, be sure to click this button Panorama Creation Tool Display ScreenVC-C4R panorama picture Capturing Panorama PicturesDisplay ranges of the panorama pictures are different VC-C4 panorama pictureTo Delete Updating/Deleting Panorama PicturesOpening/Saving Pictures ReconnectingDisplaying Connection Information View Restriction Tool View Restriction Tool Display Screen To save the settings to the VB150View Restriction Tool Changing Settings from the View Restriction Preview Frame Setting View RestrictionsTo Make Settings Restriction on from the Privilege menu → P.94 Reflecting preset settings to the viewer Preset Setting ToolSetting presets using the Preset Setting Tool Preset Setting Tool Display Screen Page Changing Settings from the Preset Preview Frame Setting PresetsConnected Motion Detection Setting Tool Motion Detection Setting Tool Display Screen Motion Detection Setting Tool Continuous motion detection Specifying the Motion Detection Function SettingsScheduled motion detection Choose -Not Specified- in the Detection preset selection box Setting the detection location and areaSetting the sensitivity Setting the motion detection parametersSetting the duration Setting the area ratioSetting the Action Performed Motion detected peak display in this tool ErrorsDisplaying Motion Detection Status of the Server Motion detection status of the server display may not matchSaving Settings to the VB150 Setting the Frame RateDownloading Log Files Log ViewerTo Download Viewing the Log Using selection criteria to display logsTo Set Selection Criteria These log messages refer to the system’s Http server Application Log messages related to applications → P.23Recording Http Server Log messages related to the Http server → P.27Starting Up Admin Viewer Admin ViewerAbout the special privileges of administrators Displaying and saving the external device input status Operating External DevicesTo Set External Device Input To Set External Device Output To Enable or Disable View RestrictionsEnabling/Disabling View Restrictions Operating External Device OutputAdvanced Camera Control Operating a CameraClicking the screen to control the camera Controlling NU-700 Appendix Troubleshooting This file Wireless LAN card does not work and communication failsCannot control the camera Cannot record or search picturesWire connection of the camera control cable RS-232C SpecificationsExternal Device Input Terminals In1, In2 External Device I/O TerminalsExternal Device Output Terminals Out1, Out2 VB150 System ConfigurationViewer for Java Viewer for PCBe sure to assign a fixed IP address on the VB150 Sample Network ConfigurationsSample LAN Environment Configuration Sample Dialup Environment ConfigurationSample ISP Environment Configuration Sample LAN plus Dialup Environment ConfigurationSample Wireless LAN Environment Configuration Launch the vb150rfu.exe program on the enclosed CD-ROM Use the procedure below to perform the remote upgradeUpgrading the Firmware Remotely Obtain the new firmwareFactory default settings using the Restore button → P.109 Restoring the Factory Default SettingsInitializing settings other than system/network settings Initializing all settingsSetting Item Setting 1 y m d Item setting 2 y m d Factory Default Setting110 To use a Web browser as an FTP client Using a PC CardProcedure for Using Flash Memory Cards Insert the flash memory card Into the VB150Connection information Index113 114 Imprimé AU Japon
Top Page Image Contents