Classe Audio SSP-800 owner manual CAN-Bus Input and Output, 20 10-Channel Analog Outputs

Page 20

20

19CAN-Bus Input and Output

CAN-Bus (Controller Area Network) allows several Classé components to be connected together for simultaneous operation, such as switching from On to Standby. Using the CAN-Bus Input and Output connectors, the Classé components can be daisy chained together and controlled via the CAN-Bus interface.

NOTE: The ﬁnal component in the daisy chain MUST have a termination plug inserted into the CAN-Bus output.

For more information, refer to the CAN-Bus section found later in this manual.

2010-Channel Analog Outputs

The SSP-800 supports ten analog audio outputs, with both balanced (XLR) and single-ended (RCA) connections. Connect the appropriate Front L/R, Sub, Surr L/R, and Rear L/R connectors to the appropriate power ampliﬁers.

NOTE: The Rear L/R connectors are only active when the

SSP-800 output is setup for a 7.1-channel surround system.

The Aux 1 and 2 outputs are programmable and can be used for the following purposes:

•Assigned as a 2-channel down-mix of the selected multi-channel signal for either an analog recorder or a separate listening area.

•Assigned to follow the main Front L/R speakers for use in a biampliﬁcation arrangement.

•One or both may be assigned as additional subwoofers with the ability to select between mono, and stereo modes.

Refer to the Menu System section for more details regarding optional uses for the auxiliary analog output channels.

NOTE: The Balanced (XLR) Output pin assignments adhere to the AES (Audio Engineering Society) “Pin 2 = hot” standard. The XLR male outputs carry the following pin assignments:

Pin 1: Signal ground

Pin 2: Signal + (non-inverting)

Pin 3: Signal – (inverting)

Connector ground lug: chassis ground

Refer to the operating manuals of your balanced-input power ampliﬁers to verify that the pin assignments of their input connectors adhere to this standard (Classé power ampliﬁers are compliant). If your ampliﬁers are not compliant, ask your Classé dealer for assistance.

Image 20

Contents SSP-800 Surround Sound Processor Page Important Safety Instructions Contents Configuration Use Video Next input Introduction Welcome to the Classé familyExceptional Design Features Page Unpacking and Placement Unpacking your SSP-800Placement considerations Warm-up/break-in period Operating voltage Voltage protection Front Panel Standby/On SwitchMenu On/Off Switch Volume Control Knob TouchscreenAudio Mute Control IR windowRear Panel Video InputsHdmi Inputs Composite Video InputsComponent Video Inputs Hdmi Outputs Component Video OutputDigital Audio Inputs Coaxial Digital Audio Inputs OpticalDigital Audio Output Coaxial Digital Audio Output Optical11 7.1-Channel Analog Audio Inputs 12 2-Channel Balanced Analog Audio InputsIR Input IR OutputTrigger Outputs USB Port 18 RS-232 PortCAN-Bus Input and Output 20 10-Channel Analog OutputsMain Power On/Off Switch AC Power Cord InputRemote Control Basic FunctionsAudio Processing Functions Input Sel Selection ButtonPreset Config Configuration Button Volume Control & Mute ButtonsNavigation & Menu Buttons Function Keys F1 to F4Choose the appropriate cables Initial SetupStep Connect all source components to the SSP-800 rear panel Terminals to black terminals Power up the system Understanding Surround Sound Name Post-processing DTS-HDUsing the SSP-800 Source selectionMode selection Name DescriptionData in the soundtrack Controls System trimsConfiguration select Menu System System setup Volume setupMax volume Startup volume IR setup Automation Mute setup Input setup NameAudio Configuration Use Video Next input TriggersProfiles Room EQ Configuration Name Distances Levels Use SpeakersSpeakers available Auxiliary channels Black level Teach IRDisplay setup Brightness TimeoutLanguage OSD on screen display Colors Volume Dolby/DTS Dolby Pro Logic DTS Neo6Remote Fkeys Important note on Fkey useFeatures Version info SensorsHardware setup Classé Delta Series ProductsCategory 5 Network Cables CAN-Bus Terminator SSP-300 & 600 CAN-Bus Interface BoxUsing CAN-Bus CAN-Bus shared features Configuration Operate AC status StatusPlayLink Amp info Event log There is no sound and the Standby LED is not lit TroubleshootingEverything appears to be powered on, but there is no sound IR remote control does not seem to function Only one speaker seems to be playingThere is a hum coming out of the speakers There is a hum coming from the SSP-800Voltage Protection Circuit Care & Maintenance Input factory defaultsSpecifications Overall dimensionsNet weight Shipping weightDimensions Installation Worksheet Page North America 1 800 370 3740 email classe@bwgroupusa.com