Classe Audio SSP-800 owner manual Speakers available

Page 47

Each speaker opens the same menu with two buttons – size and crossover. To modify the crossover for the selected speaker, touch the Crossover button and then adjust the setting using the increase and decrease buttons. The crossover setting applies a high pass filter to the speakers set on crossed over, and a low pass filter to route bass information to the sub (if enabled). When the speaker is set to large, and e-bassis enabled the crossover determines which low frequencies will simultaneously get routed to the sub(s).

The Size option allows you to pick either Full Range or Crossed Over for each speaker. The None option is available on the surround, center, or rears. Selecting None disables the channel(s) output. If None is highlighted then that speaker location is not available for selection in other menus.

NOTE: You cannot disable the Front L/R. If you disable the surround speakers, then the rear speakers are not available for selection.

The Subwoofer configuration page, shown above, has two buttons available

Sub Enabled and e-bass. If the Sub Enabled button is highlighted, then the configuration includes an active subwoofer and the LFE (Low Frequency Effects) information is routed to it as well as any low pass energy from the crossed

over channels. If you do not enable a subwoofer for the system, then the LFE information will be routed to any full range speakers in the configuration. When a subwoofer is enabled and the e-bass option selected, the low frequency signals from all speakers (both crossed and full range) are passed to the subwoofer along with the LFE (if available from a discrete stream). This effectively duplicates the bass energy present in full range speakers.

NOTE: If the Sub is not enabled e-bass will be grayed out and not selectable as the LFE is already being distributed to any full range

speakers available.

The Crossover Slope button enables you to select the preferred crossover slope, either 12dB/octave or a steeper 24dB/octave. Touch the desired value so that it is highlighted.

47

Image 47
Contents SSP-800 Surround Sound Processor Page Important Safety Instructions Contents Configuration Use Video Next input Welcome to the Classé family IntroductionExceptional Design Features Page Unpacking your SSP-800 Unpacking and PlacementPlacement considerations Warm-up/break-in period Operating voltage Voltage protection Front Panel Standby/On SwitchMenu On/Off Switch IR window Volume Control KnobTouchscreen Audio Mute ControlVideo Inputs Rear PanelHdmi Inputs Composite Video InputsComponent Video Inputs Digital Audio Inputs Optical Hdmi OutputsComponent Video Output Digital Audio Inputs Coaxial12 2-Channel Balanced Analog Audio Inputs Digital Audio Output CoaxialDigital Audio Output Optical 11 7.1-Channel Analog Audio InputsUSB Port 18 RS-232 Port IR InputIR Output Trigger Outputs20 10-Channel Analog Outputs CAN-Bus Input and OutputAC Power Cord Input Main Power On/Off SwitchInput Sel Selection Button Remote ControlBasic Functions Audio Processing FunctionsFunction Keys F1 to F4 Preset Config Configuration ButtonVolume Control & Mute Buttons Navigation & Menu ButtonsChoose the appropriate cables Initial SetupStep Connect all source components to the SSP-800 rear panel Terminals to black terminals Power up the system Understanding Surround Sound Name DTS-HD Post-processingSource selection Using the SSP-800Name Description Mode selectionData in the soundtrack System trims ControlsConfiguration select Menu System Volume setup System setupMax volume Startup volume IR setup Automation Mute setup Name Input setupAudio Configuration Triggers Use Video Next inputProfiles Room EQ Configuration Name Distances Use Speakers LevelsSpeakers available Auxiliary channels Teach IR Black levelBrightness Timeout Display setupLanguage OSD on screen display Colors Volume Dolby Pro Logic DTS Neo6 Dolby/DTSImportant note on Fkey use Remote FkeysVersion info Sensors FeaturesCAN-Bus Terminator SSP-300 & 600 CAN-Bus Interface Box Hardware setupClassé Delta Series Products Category 5 Network CablesUsing CAN-Bus Configuration Operate AC status Status CAN-Bus shared featuresPlayLink Amp info Event log There is no sound and the Standby LED is not lit TroubleshootingEverything appears to be powered on, but there is no sound There is a hum coming from the SSP-800 IR remote control does not seem to functionOnly one speaker seems to be playing There is a hum coming out of the speakersVoltage Protection Circuit Input factory defaults Care & MaintenanceShipping weight SpecificationsOverall dimensions Net weightDimensions Installation Worksheet Page North America 1 800 370 3740 email classe@bwgroupusa.com