Sharp PN-Y325 operation manual Safety Precautions

Page 5

SAFETY PRECAUTIONS (Continued)

19. Batteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment, dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below:

Use the specified batteries only.

Install the batteries with due attention to the plus (+) and minus (-) sides of the batteries according to the instructions in the compartment.

Do not mix old and new batteries.

Do not mix batteries of different types. Voltage specifications of batteries of the same shape may vary.

Replace an exhausted battery with a new one promptly.

If you will not use the remote control for a long time, remove the batteries.

If leaked battery fluid gets on your skin or clothing, rinse immediately and thoroughly. If it gets into your eye, bathe your eye well rather than rubbing and seek medical treatment immediately. Leaked battery fluid that gets into your eye or your clothing may cause a skin irritation or damage your eye.

20. Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury, severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and missile launch control in a weapon system.

21. Do not stay in contact with the parts of the product that become hot for long periods of time. Doing so may result in low-temperature burns.

22. To prevent fire or shock hazard, do not expose this product to dripping or splashing. No objects filled with liquids, such as vases, should be placed on the product.

WARNING:

1)This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

2)Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

3)To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.

To maintain compliance with EMC regulations, use shielded cables to connect to the following terminals: DVI-D input/output terminals, HDMI input terminal, D-sub input terminal, and RS-232C input/output terminals.

If a monitor is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling. Many injuries, particularly to children, can be avoided by taking simple precautions such as:

Using fixing devices like wall mount brackets recommended by the manufacturer.

Only using furniture that can safely support the monitor.

Ensuring the monitor is not overhanging the edge of the supporting furniture.

Not placing the monitor on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the monitor to a suitable support.

Not standing the monitors on cloth or other materials placed between the monitor and supporting furniture.

Educating children about the dangers of climbing on furniture to reach the monitor or its controls.

Especially for child safety

-Don’t allow children to climb on or play with the monitor.

-Don’t place the monitor on furniture that can easily be used as steps, such as a chest of drawers.

-Remember that children can become excited while watching a program, especially on a “larger than life” monitor. Care should be taken to place or install the monitor where it cannot be pushed, pulled over, or knocked down.

-Care should be taken to route all cords and cables connected to the monitor so that they cannot be pulled or grabbed by curious children.

5 E

Image 5
Contents PN-Y325 Page Blue Neutral Brown Live Refer Servicing to Qualified Service PersonnelConnecting Plug to Mains Lead Dear Sharp Customer Safety Precautions Safety Precautions Tips and Safety Instructions For the monitor in portrait orientation For the monitor in landscape orientationSupplied Components ContentsPart Names LCD panel Remote control sensor SeeNFront view NRear viewSignal transmitter NRemote control unit Part Names11 E Return button See SIZE/Yellow button SeeConnecting Peripheral Equipment 13 E Connecting Peripheral EquipmentConnecting the Power Cord Binding Cables Setting the USB flash drive cover15 E USB flash drive cover screw USB portInstalling the batteries Preparing the Remote Control UnitRemote control operation range 16.4Turning power on/off Turning Power On/OffTurning on the main power 17 ESetting of the Setup menu. Be sure to set the date and time Turning Power On/Off NOperation modeNDate/time setting 19 E Basic OperationDot by Dot Basic Operation NSwitching the screen sizeNormal Wide 21 E Playing the Files in a USB Flash DriveAuto playback Playing filesPhoto Playing files using the Schedule functionMovie MusicOperations during play Settings23 E Color Mode Playing the Files in a USB Flash Drive Settings during playVolume Size25 E Menu ItemsDisplaying the menu screen NExample of operationMenu Items Menu item detailsNSCREEN NPICTUREMenu Items NAUDIO NSETUP27 E Scan Mode Hdmiav Power on DelayAdjustment Lock Remote ControlSet using Multi in the Setup menu Setting procedure29 E Menu Items NEnlargeMenu Items NSCHEDULE Opening the adjustment pattern Menu Items NScreen display for adjustment31 E ScheduleControlling the Monitor with a PC RS-232C Communication procedureCommunication conditions PC connectionNResponse code format NID Setting33 E VOLM0030 002VOLM0020 ← OK 002 IDLK0000 ← Wait ← OK 002 ← VOLM0010 OK 001 ←Volume settings for all monitors are returned NRepeater control command35 E Controlling the Monitor with a PC RS-232C NRepeater controlPower control/Input mode selection RS-232C command tableControlling the Monitor with a PC RS-232C Screen menuOthers Controlling the Monitor with a PC RS-232C Setup menu37 E Controlling the Monitor with a PC LAN Settings to connect to a LANTo set on the monitor Character inputControlling the Monitor with a PC LAN Command-based control39 E Troubleshooting 41 E TroubleshootingPower LED is flashing in red and green alternately NProduct Specifications Specifications43 E NDimensional DrawingsSpecifications NDDC plug and play Specifications NPower managementDmpm Digital Monitor Power Management NCompatible signal timing AV Specifications NCompatible signal timing PC45 E DVI-D HdmiNHDMI input terminal pins Specifications NDVI-D input terminal pinsND-sub input terminal pins NRS-232C input terminal pins47 E NDVI-D output terminal pinsSpecifications NRS-232C output terminal pins Mounting Precautions For Sharp dealers and service engineers PN-Y325 Me EN14G2