Sharp PN-Y325 operation manual Tips and Safety Instructions

Page 7

TIPS AND SAFETY INSTRUCTIONS

-The TFT color LCD panel used in this monitor is made with the application of high precision technology. However, there may be minute points on the screen where pixels never light or are permanently lit. Also, if the screen is viewed from

an acute angle there may be uneven colors or brightness. Please note that these are not malfunctions but common phenomena of LCDs and will not affect the performance of the monitor.

-Do not display a still picture for a long period, as this could cause a residual image.

-Never rub or tap the monitor with hard objects.

-Please understand that SHARP CORPORATION bears no responsibility for errors made during use by the customer or a third party, nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is recognized under law.

-This monitor and its accessories may be upgraded without advance notice.

-Do not use the monitor where there is a lot of dust, where humidity is high, or where the monitor may come into contact with oil or steam. Do not use in an environment where there are corrosive gases (sulfur dioxide, hydrogen sulfide, nitrogen dioxide, chlorine, ammonia, ozone, etc.). As this could lead to fire.

-Ensure that the monitor does not come into contact with water or other fluids. Ensure that no objects such as paper clips or pins enter the monitor as this could lead to fire or electric shock.

-Do not place the monitor on top of unstable objects or in unsafe places. Do not allow the monitor to receive strong shocks or to strongly vibrate. Causing the monitor to fall or topple over may damage it.

-Do not use the monitor near heating equipment or in places where there is likelihood of high temperature, as this may lead to generation of excessive heat and outbreak of fire.

-Do not use the monitor in places where it may be exposed to direct sunlight.

-Please be sure to constantly remove dust and garbage that has attached to the ventilation opening. If dust collects in the ventilation opening or the inside of the monitor, it may lead to excessive heat, outbreak of fire, or malfunction.

Please request a cleaning of the inside of the monitor from an authorized SHARP servicing dealer or service center.

-Images cannot be rotated on this monitor.

When using in portrait orientation, you will need to prepare appropriately orientated content in advance.

-The AC outlet shall be installed near the equipment and shall be easily accessible.

The Power Cord

-Use only the power cord supplied with the monitor.

-Do not damage the power cord nor place heavy objects on it, stretch it or over bend it. Also, do not add extension cords.

Damage to the cord may result in fire or electric shock.

-Do not use the power cord with a power tap.

Adding an extension cord may lead to fire as a result of overheating.

-Do not remove or insert the power plug with wet hands. Doing so could result in electric shock.

-Unplug the power cord if it is not used for a long time.

-Do not attempt to repair the power cord if it is broken or malfunctioning. Refer the servicing to the service representative.

Manual Scope

-Microsoft, Windows and Internet Explorer are registered trademarks of Microsoft Corporation.

-The terms HDMI and HDMI High-Definition Multimedia

Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

-Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.

-All other brand and product names are trademarks or registered trademarks of their respective holders.

-Language of OSD menu used in this manual is English by way of example.

-Illustrations in this manual may not exactly represent the actual product or display.

-This manual assumes use in landscape orientation, except where specifically noted.

LED Backlight

The LED backlight in this product has a limited lifetime.

*If the screen gets dark or does not turn on, it may be necessary to replace the LED backlight.

*This LED backlight is exclusive to this product and must be replaced by an authorized SHARP servicing dealer or service center. Please contact an authorized SHARP servicing dealer or service center for assistance.

7 E

Image 7
Contents PN-Y325 Page Connecting Plug to Mains Lead Refer Servicing to Qualified Service PersonnelBlue Neutral Brown Live Dear Sharp Customer Safety Precautions Safety Precautions Tips and Safety Instructions For the monitor in portrait orientation For the monitor in landscape orientationSupplied Components ContentsNRear view LCD panel Remote control sensor SeePart Names NFront viewReturn button See SIZE/Yellow button See NRemote control unit Part NamesSignal transmitter 11 EConnecting Peripheral Equipment 13 E Connecting Peripheral EquipmentConnecting the Power Cord USB flash drive cover screw USB port Setting the USB flash drive coverBinding Cables 15 E16.4 Preparing the Remote Control UnitInstalling the batteries Remote control operation range17 E Turning Power On/OffTurning power on/off Turning on the main powerNDate/time setting Turning Power On/Off NOperation modeSetting of the Setup menu. Be sure to set the date and time 19 E Basic OperationNormal Wide Basic Operation NSwitching the screen sizeDot by Dot Playing files Playing the Files in a USB Flash Drive21 E Auto playbackMusic Playing files using the Schedule functionPhoto Movie23 E SettingsOperations during play Size Playing the Files in a USB Flash Drive Settings during playColor Mode VolumeNExample of operation Menu Items25 E Displaying the menu screenNPICTURE Menu item detailsMenu Items NSCREEN27 E NSETUPMenu Items NAUDIO Remote Control Power on DelayScan Mode Hdmiav Adjustment LockMenu Items NEnlarge Setting procedureSet using Multi in the Setup menu 29 EMenu Items NSCHEDULE Schedule Menu Items NScreen display for adjustmentOpening the adjustment pattern 31 EPC connection Communication procedureControlling the Monitor with a PC RS-232C Communication conditions33 E NID SettingNResponse code format OK 002 IDLK0000 ← Wait ← OK 002 ← VOLM0010 OK 001 ← 002VOLM0030 VOLM0020 ←Controlling the Monitor with a PC RS-232C NRepeater control NRepeater control commandVolume settings for all monitors are returned 35 EScreen menu RS-232C command tablePower control/Input mode selection Controlling the Monitor with a PC RS-232C37 E Controlling the Monitor with a PC RS-232C Setup menuOthers Character input Settings to connect to a LANControlling the Monitor with a PC LAN To set on the monitor39 E Command-based controlControlling the Monitor with a PC LAN Troubleshooting Power LED is flashing in red and green alternately Troubleshooting41 E NProduct Specifications SpecificationsSpecifications NDimensional Drawings43 E Dmpm Digital Monitor Power Management Specifications NPower managementNDDC plug and play DVI-D Hdmi Specifications NCompatible signal timing PCNCompatible signal timing AV 45 ENRS-232C input terminal pins Specifications NDVI-D input terminal pinsNHDMI input terminal pins ND-sub input terminal pinsSpecifications NRS-232C output terminal pins NDVI-D output terminal pins47 E Mounting Precautions For Sharp dealers and service engineers PN-Y325 Me EN14G2