Kenwood TM-V71E, TM-V71A Basic Operations, Switching the Power ON/ OFF, Adjusting the Volume

Page 22

BASIC OPERATIONS

Switching THE Power ON/ OFF

Press the [] switch to switch the transceiver ON.

•The power on message momentarily appears on the display.

•If the transceiver power on password has been activated {page 74}, you must first enter your password before you can operate the transceiver.

Press the [] switch again to switch the transceiver OFF.

Adjusting the Volume

Rotate the [BAND SEL] (VOL) control of your selected band clockwise to increase the volume and counterclockwise to decrease the volume.

Note: Some functions of this transceiver, such as the beep and voice announcements, have their own volume settings. Adjust those settings to your desired values.

Image 22

Contents 144/440 MHz FM Dual Bander 144/430 MHz FM Dual BanderThank You FeaturesThis transceiver has the following main features Writing Conventions Followed in this ManualWhen Condensation Occurs Inside the Transceiver One or more of the following statements may be applicablePrecautions Contents Using DCS DCS Code ID Using Ctcss Ctcss Frequency IDManual Dialing Automatic dialer Dtmf Key Lock VGS-1 Optional Voice Guide & Storage UnitOptions Preparation Supplied AccessoriesMobile Installation Part Number QuantityPower Cable Connection Mobile OperationFixed Station Operation Replacing Fuses Located on the DC connectorSupplied DC power cable Fuse Location Fuse Current RatingAntenna Connection Front Panel Orientation External Speakers Accessory ConnectionsMicrophone Getting Acquainted Front PanelPF1 REVLOW 0PF2Indicator Description DisplayAppears while accessing the Menu Rear Panel Sub-PanelMicrophone MC-59 Press the switch to switch the transceiver on Switching the Power ON/ OFFAdjusting the Volume Press the switch again to switch the transceiver OFFSelecting a Band Adjusting the SquelchBand a left Band SEL control Band B right Band SEL control Selecting Dual band mode/ single band Mode Selecting a frequency band Frequency rangesVFO Mode Selecting an Operating modeMemory Channel Mode When you finish speaking, release the PTT switch Call Channel ModePress Call to enter Call Channel mode TransmittingMenu Configuration Menu ModeMenu Access Press F, Tuning control to access the MenuANN.SPD DT.SPD MIC.LCK Character Entry Rotate the Tuning control to select your desired characterPress the Tuning control to set the selected character Repeat steps 2 and 3 to enter the remaining charactersMicrophone Keypad Character Entry Key Character Display with each press of the keyOperating Through Repeaters Repeater AccessSelecting an Offset Direction Selecting an Offset Frequency Activating the Tone FunctionPress F, Tone Rotate the Tuning control to select your desired frequencySelecting a Tone Frequency FrequencyAutomatic Repeater Offset K and E Types Only Reverse Function Transmitting a 1750 Hz ToneAutomatic Simplex Checker ASC Tone Frequency ID Press F, Tone 1s to run the Tone Frequency ID scanSimplex & Repeater or ODD-SPLIT Memory CHANNEL? Memory ChannelsParameter Simplex Odd-split Storing Odd-Split Repeater Frequencies Storing Simplex and Standard Repeater FrequenciesCall Channel Memory Simplex Call Channel Memory Odd-Split Recalling a Memory ChannelMemory Recall Method Press the Tuning control to clear the Memory channel Turn the transceiver power OFFPress MR + Power on Clearing a Memory ChannelChannel Display FUnction Switching the Memory Name/ Frequency DisplayMemory-TO-VFO TRansfer Press F, VFOKey Name KEY KEY 1s While KEY +Programmable Memory PM Application Examples Recalling PM Channels Storing Data in PM ChannelsPress F, PM Press the Tuning control again to reset the PM channels PM Channel ResetPress F + Power on Auto PM Channel storeScan Scan Type Scan RangeSelecting a Scan Resume Method VFO ScanPress MR 1s Memory ScanLocking Out a Memory Channel To quit Memory Scan, press MR againMemory Group Link To quit Group Scan, press the Tuning control againGroup Scan Memory Group Channel RangeProgram Scan Setting Scan LimitsPress VFO Using Program Scan To quit Program Scan, press VFO againCall Scan To quit MHz Scan, press the Tuning control againMHz Scan To quit Call Scan, press Call againUsing Ctcss Continuous Tone Coded Squelch System CtcssPress Enter again to complete the setting Ctcss FREQuency ID Press F, Tone 1sRotate the Tuning control to select your desired DCS code Using DCSDigital Coded Squelch DCS DCS Code DCS Code ID Dtmf Hold Dual Tone MULTI-FREQUENCY DtmfManual Dialing 1209 1336 1447 1633 697 770 852 941Automatic Dialer Storing a Dtmf Code in MemoryTransmitting Stored Dtmf Codes Selecting a Transmit SpeedDtmf Key Lock Selecting a Pause DurationWhat is EchoLink? Storing EchoLink memoryTransmitting EchoLink Memory EchoLink Sysop Mode OFF TM-V71 Setting Up EchoLink Sysop ModeEchoLink Sysop Mode on TM-V71 TxD RxDDisplay Brightness POWER-ON MessageAuxiliary Functions Auto Display BrightnessMicrophone Key Lock Key LockBacklight Color To turn Key Lock on or OFF, press F 1sKey Beep Beep VolumeProgrammable VFO Changing the Frequency Step Size Transceiver Front Panel Programmable Function KeysMicrophone Keys Automatic Power OFF APO Frequency Direct EntryAdvanced Intercept Point AIP Meter SquelchSquelch Hang Time Beat Shift Switching FM/AM ModeSpeaker Mute TIME-OUT Timer TOT Selecting an Output PowerMute Hang Time Masking a Band External Speaker ConfigurationSetup Speaker Band OutputDisplay Partition Bar Channel No Weather Alert K Type Models OnlyWeather Channel Memory Name LocationPower On Password Enter your passwordOperation Announcement VGS-1 Optional Voice Guide & Storage UnitVoice Announcements Current frequency/codeAuto Voice Announcement Language Voice Announcement VolumeVoice Announcement Speed Voice Recorder Voice MemosConversation Recorder Playback Repeat PlaybackPlayback Repeat Interval Press Tone + Power on CROSS-BAND/ LOCKED-BAND Operation K Type Models onlyRepeater ID Repeater HoldEntering your Repeater ID Data Band Data terminal pinsPacket Operation Data Terminal SpeedSQC Output Setting PC Port SpeedWireless Operation K Type Models only PreparationOperation Dtmf Command Control OperationTransceiver Reset Menu Mode Options Using the MCP-2A SoftwareUsing the MCP-2A software, you can Memory control program MCP-2AInstalling the Sub-Panel Connecting the PG-5G/ PG-5H interface cablesInstalling the DFK-3D panel kit PC terminal pinsConnect the supplied sub-panel to Installing the Panel BracketClean and dry the installation location Operation panelConnecting Using Two Extension Kits Connecting the PG-5F extension cableConnecting Using a Single Extension Kit Installing the Line FilterInsert the VGS-1 unit into the connector On the transceiver Installing the VGS-1 UnitFrom the remaining cushions, select Service Note MaintenanceService CleaningProblem Probable Cause Corrective Action TroubleshootingUP/DWN General SpecificationsType M4 Type Transmitter Receiver