Kenwood TM-V71A, TM-V71E instruction manual Press F, Tone 1s to run the Tone Frequency ID scan

Page 39

•When the ASC is ON, the icon will appear on the display.

•While direct contact is possible, without the use of a repeater, the icon will begin blinking.

•To exit ASC, press [REV].

Note:

uPressing [PTT] will cause the icon to stop blinking.

uASC does not function if you are using simplex operation.

uASC does not function while scanning.

uActivating ASC while using Reverse will switch the Reverse function OFF.

uIf you recall a Memory channel or the Call channel, and those channels are set up with the Reverse function switched ON, the ASC will switch OFF.

uASC causes received signals to be momentarily intermitted every 3 seconds.

Tone Frequency ID

This function scans through all tone frequencies to identify the incoming tone frequency on a received signal. You can use this function to find which tone frequency is required by your local repeater.

1Press [TONE] to switch the Tone function ON.

•The icon appears on the display.

2Press [F], [TONE] (1s) to run the Tone Frequency ID scan.

•The icon blinks and SCAN appears on the display.

•To reverse the scan direction, turn the Tuning control clockwise (upward scan) or counterclockwise (downward scan).

•To quit the function, press [F] (ESC).

•When the tone frequency is identified, the identified frequency appears on the display and blinks. Press any key other than the Tuning control while the identified frequency is blinking, to resume scanning.

3Press the Tuning control to program the identified frequency in place of the currently set tone frequency.

•The Tone function will remain ON. You can press [TONE] to switch the Tone function OFF.

•Press [F] (ESC) if you do not want to program the identified frequency.

31

Image 39

Contents 144/430 MHz FM Dual Bander 144/440 MHz FM Dual BanderWriting Conventions Followed in this Manual FeaturesThis transceiver has the following main features Thank YouOne or more of the following statements may be applicable When Condensation Occurs Inside the TransceiverPrecautions Contents Using Ctcss Ctcss Frequency ID Using DCS DCS Code IDManual Dialing Automatic dialer VGS-1 Optional Voice Guide & Storage Unit Dtmf Key LockOptions Part Number Quantity Supplied AccessoriesMobile Installation PreparationMobile Operation Power Cable ConnectionFixed Station Operation Fuse Location Fuse Current Rating Located on the DC connectorSupplied DC power cable Replacing FusesAntenna Connection Front Panel Orientation Accessory Connections External SpeakersMicrophone Front Panel Getting Acquainted0PF2 REVLOW PF1Display Indicator DescriptionAppears while accessing the Menu Sub-Panel Rear PanelMicrophone MC-59 Press the switch again to switch the transceiver OFF Switching the Power ON/ OFFAdjusting the Volume Press the switch to switch the transceiver onAdjusting the Squelch Selecting a BandBand a left Band SEL control Band B right Band SEL control Selecting Dual band mode/ single band Mode Frequency ranges Selecting a frequency bandSelecting an Operating mode VFO ModeMemory Channel Mode Transmitting Call Channel ModePress Call to enter Call Channel mode When you finish speaking, release the PTT switchPress F, Tuning control to access the Menu Menu ModeMenu Access Menu ConfigurationANN.SPD DT.SPD MIC.LCK Repeat steps 2 and 3 to enter the remaining characters Rotate the Tuning control to select your desired characterPress the Tuning control to set the selected character Character EntryKey Character Display with each press of the key Microphone Keypad Character EntryRepeater Access Operating Through RepeatersSelecting an Offset Direction Activating the Tone Function Selecting an Offset FrequencyFrequency Rotate the Tuning control to select your desired frequencySelecting a Tone Frequency Press F, ToneAutomatic Repeater Offset K and E Types Only Transmitting a 1750 Hz Tone Reverse FunctionAutomatic Simplex Checker ASC Press F, Tone 1s to run the Tone Frequency ID scan Tone Frequency IDMemory Channels Simplex & Repeater or ODD-SPLIT Memory CHANNEL?Parameter Simplex Odd-split Storing Simplex and Standard Repeater Frequencies Storing Odd-Split Repeater FrequenciesCall Channel Memory Simplex Recalling a Memory Channel Call Channel Memory Odd-SplitMemory Recall Method Clearing a Memory Channel Turn the transceiver power OFFPress MR + Power on Press the Tuning control to clear the Memory channelPress F, VFO Switching the Memory Name/ Frequency DisplayMemory-TO-VFO TRansfer Channel Display FUnctionKEY KEY 1s While KEY + Key NameProgrammable Memory PM Application Examples Storing Data in PM Channels Recalling PM ChannelsPress F, PM Auto PM Channel store PM Channel ResetPress F + Power on Press the Tuning control again to reset the PM channelsScan Type Scan Range ScanVFO Scan Selecting a Scan Resume MethodTo quit Memory Scan, press MR again Memory ScanLocking Out a Memory Channel Press MR 1sMemory Group Channel Range To quit Group Scan, press the Tuning control againGroup Scan Memory Group LinkSetting Scan Limits Program ScanPress VFO To quit Program Scan, press VFO again Using Program ScanTo quit Call Scan, press Call again To quit MHz Scan, press the Tuning control againMHz Scan Call ScanContinuous Tone Coded Squelch System Ctcss Using CtcssPress Enter again to complete the setting Press F, Tone 1s Ctcss FREQuency IDUsing DCS Rotate the Tuning control to select your desired DCS codeDigital Coded Squelch DCS DCS Code DCS Code ID 1209 1336 1447 1633 697 770 852 941 Dual Tone MULTI-FREQUENCY DtmfManual Dialing Dtmf HoldStoring a Dtmf Code in Memory Automatic DialerSelecting a Transmit Speed Transmitting Stored Dtmf CodesSelecting a Pause Duration Dtmf Key LockStoring EchoLink memory What is EchoLink?Transmitting EchoLink Memory TxD RxD Setting Up EchoLink Sysop ModeEchoLink Sysop Mode on TM-V71 EchoLink Sysop Mode OFF TM-V71Auto Display Brightness POWER-ON MessageAuxiliary Functions Display BrightnessTo turn Key Lock on or OFF, press F 1s Key LockBacklight Color Microphone Key LockBeep Volume Key BeepProgrammable VFO Changing the Frequency Step Size Programmable Function Keys Transceiver Front PanelMicrophone Keys Frequency Direct Entry Automatic Power OFF APOMeter Squelch Advanced Intercept Point AIPSquelch Hang Time Switching FM/AM Mode Beat ShiftSpeaker Mute Selecting an Output Power TIME-OUT Timer TOTMute Hang Time Speaker Band Output External Speaker ConfigurationSetup Masking a BandDisplay Partition Bar Memory Name Location Weather Alert K Type Models OnlyWeather Channel Channel NoEnter your password Power On PasswordCurrent frequency/code VGS-1 Optional Voice Guide & Storage UnitVoice Announcements Operation AnnouncementAuto Voice Announcement Volume Voice Announcement LanguageVoice Announcement Speed Voice Memos Voice RecorderConversation Recorder Playback Playback RepeatPlayback Repeat Interval CROSS-BAND/ LOCKED-BAND Operation K Type Models only Press Tone + Power onRepeater Hold Repeater IDEntering your Repeater ID Data Terminal Speed Data terminal pinsPacket Operation Data BandPC Port Speed SQC Output SettingPreparation Wireless Operation K Type Models onlyControl Operation Operation Dtmf CommandTransceiver Reset Menu Mode Memory control program MCP-2A Using the MCP-2A SoftwareUsing the MCP-2A software, you can OptionsPC terminal pins Connecting the PG-5G/ PG-5H interface cablesInstalling the DFK-3D panel kit Installing the Sub-PanelOperation panel Installing the Panel BracketClean and dry the installation location Connect the supplied sub-panel toInstalling the Line Filter Connecting the PG-5F extension cableConnecting Using a Single Extension Kit Connecting Using Two Extension KitsInstalling the VGS-1 Unit Insert the VGS-1 unit into the connector On the transceiverFrom the remaining cushions, select Cleaning MaintenanceService Service NoteTroubleshooting Problem Probable Cause Corrective ActionUP/DWN Specifications GeneralType M4 Type Receiver Transmitter