Kenwood TM-V71E, TM-V71A instruction manual Automatic Dialer, Storing a Dtmf Code in Memory

Page 64

Automatic Dialer

There are 10 dedicated DTMF Memory channels available to store DTMF codes. You can store up to 16 digits in each channel.

nStoring a DTMF Code in Memory

1 Enter Menu mode and access Menu 301 (DT.MEM) {page 20}.

2 Rotate the Tuning control to select a channel number.

3 Press the Tuning control to set the selected channel number.

The name entry display appears.

4Enter a name for the channel {page 24}, the press the Tuning control to set it.

• The code entry display appears.

5Enter a DTMF code for the channel {page 24}, then press the Tuning control to set it.

56

Image 64
Contents 144/440 MHz FM Dual Bander 144/430 MHz FM Dual BanderFeatures This transceiver has the following main featuresThank You Writing Conventions Followed in this ManualWhen Condensation Occurs Inside the Transceiver One or more of the following statements may be applicablePrecautions Contents Using DCS DCS Code ID Using Ctcss Ctcss Frequency IDManual Dialing Automatic dialer Dtmf Key Lock VGS-1 Optional Voice Guide & Storage UnitOptions Supplied Accessories Mobile InstallationPreparation Part Number QuantityPower Cable Connection Mobile OperationFixed Station Operation Located on the DC connector Supplied DC power cableReplacing Fuses Fuse Location Fuse Current RatingAntenna Connection Front Panel Orientation External Speakers Accessory ConnectionsMicrophone Getting Acquainted Front PanelREV LOWPF1 0PF2Indicator Description DisplayAppears while accessing the Menu Rear Panel Sub-PanelMicrophone MC-59 Switching the Power ON/ OFF Adjusting the VolumePress the switch to switch the transceiver on Press the switch again to switch the transceiver OFFSelecting a Band Adjusting the SquelchBand a left Band SEL control Band B right Band SEL control Selecting Dual band mode/ single band Mode Selecting a frequency band Frequency rangesVFO Mode Selecting an Operating modeMemory Channel Mode Call Channel Mode Press Call to enter Call Channel modeWhen you finish speaking, release the PTT switch TransmittingMenu Mode Menu AccessMenu Configuration Press F, Tuning control to access the MenuANN.SPD DT.SPD MIC.LCK Rotate the Tuning control to select your desired character Press the Tuning control to set the selected characterCharacter Entry Repeat steps 2 and 3 to enter the remaining charactersMicrophone Keypad Character Entry Key Character Display with each press of the keyOperating Through Repeaters Repeater AccessSelecting an Offset Direction Selecting an Offset Frequency Activating the Tone FunctionRotate the Tuning control to select your desired frequency Selecting a Tone FrequencyPress F, Tone FrequencyAutomatic Repeater Offset K and E Types Only Reverse Function Transmitting a 1750 Hz ToneAutomatic Simplex Checker ASC Tone Frequency ID Press F, Tone 1s to run the Tone Frequency ID scanSimplex & Repeater or ODD-SPLIT Memory CHANNEL? Memory ChannelsParameter Simplex Odd-split Storing Odd-Split Repeater Frequencies Storing Simplex and Standard Repeater FrequenciesCall Channel Memory Simplex Call Channel Memory Odd-Split Recalling a Memory ChannelMemory Recall Method Turn the transceiver power OFF Press MR + Power onPress the Tuning control to clear the Memory channel Clearing a Memory ChannelSwitching the Memory Name/ Frequency Display Memory-TO-VFO TRansferChannel Display FUnction Press F, VFOKey Name KEY KEY 1s While KEY +Programmable Memory PM Application Examples Recalling PM Channels Storing Data in PM ChannelsPress F, PM PM Channel Reset Press F + Power onPress the Tuning control again to reset the PM channels Auto PM Channel storeScan Scan Type Scan RangeSelecting a Scan Resume Method VFO ScanMemory Scan Locking Out a Memory ChannelPress MR 1s To quit Memory Scan, press MR againTo quit Group Scan, press the Tuning control again Group ScanMemory Group Link Memory Group Channel RangeProgram Scan Setting Scan LimitsPress VFO Using Program Scan To quit Program Scan, press VFO againTo quit MHz Scan, press the Tuning control again MHz ScanCall Scan To quit Call Scan, press Call againUsing Ctcss Continuous Tone Coded Squelch System CtcssPress Enter again to complete the setting Ctcss FREQuency ID Press F, Tone 1sRotate the Tuning control to select your desired DCS code Using DCSDigital Coded Squelch DCS DCS Code DCS Code ID Dual Tone MULTI-FREQUENCY Dtmf Manual DialingDtmf Hold 1209 1336 1447 1633 697 770 852 941Automatic Dialer Storing a Dtmf Code in MemoryTransmitting Stored Dtmf Codes Selecting a Transmit SpeedDtmf Key Lock Selecting a Pause DurationWhat is EchoLink? Storing EchoLink memoryTransmitting EchoLink Memory Setting Up EchoLink Sysop Mode EchoLink Sysop Mode on TM-V71EchoLink Sysop Mode OFF TM-V71 TxD RxDPOWER-ON Message Auxiliary FunctionsDisplay Brightness Auto Display BrightnessKey Lock Backlight ColorMicrophone Key Lock To turn Key Lock on or OFF, press F 1sKey Beep Beep VolumeProgrammable VFO Changing the Frequency Step Size Transceiver Front Panel Programmable Function KeysMicrophone Keys Automatic Power OFF APO Frequency Direct EntryAdvanced Intercept Point AIP Meter SquelchSquelch Hang Time Beat Shift Switching FM/AM ModeSpeaker Mute TIME-OUT Timer TOT Selecting an Output PowerMute Hang Time External Speaker Configuration SetupMasking a Band Speaker Band OutputDisplay Partition Bar Weather Alert K Type Models Only Weather ChannelChannel No Memory Name LocationPower On Password Enter your passwordVGS-1 Optional Voice Guide & Storage Unit Voice AnnouncementsOperation Announcement Current frequency/codeAuto Voice Announcement Language Voice Announcement VolumeVoice Announcement Speed Voice Recorder Voice MemosConversation Recorder Playback Repeat PlaybackPlayback Repeat Interval Press Tone + Power on CROSS-BAND/ LOCKED-BAND Operation K Type Models onlyRepeater ID Repeater HoldEntering your Repeater ID Data terminal pins Packet OperationData Band Data Terminal SpeedSQC Output Setting PC Port SpeedWireless Operation K Type Models only PreparationOperation Dtmf Command Control OperationTransceiver Reset Menu Mode Using the MCP-2A Software Using the MCP-2A software, you canOptions Memory control program MCP-2AConnecting the PG-5G/ PG-5H interface cables Installing the DFK-3D panel kitInstalling the Sub-Panel PC terminal pinsInstalling the Panel Bracket Clean and dry the installation locationConnect the supplied sub-panel to Operation panelConnecting the PG-5F extension cable Connecting Using a Single Extension KitConnecting Using Two Extension Kits Installing the Line FilterInsert the VGS-1 unit into the connector On the transceiver Installing the VGS-1 UnitFrom the remaining cushions, select Maintenance ServiceService Note CleaningProblem Probable Cause Corrective Action TroubleshootingUP/DWN General SpecificationsType M4 Type Transmitter Receiver