Kenwood TM-V71E, TM-V71A Storing Data in PM Channels, Recalling PM Channels, Press F, PM

Page 48

Storing Data in PM Channels

1Confirm that the following conditions have been satisfied:

•The transceiver is in receive mode.

•Scan is not being used.

•Microphone Control is OFF.

2Configure the transceiver with your desired settings.

3Press [F], [PM].

•PM channel numbers 1 to 5 appear and blink at the bottom of the display.

4Enter a channel number ([1] to [5]) corresponding to your desired PM channel.

•The settings are stored in the PM channel.

Recalling PM Channels

1Press [PM].

•PM channel numbers 1 to 5 and OFF appear on the bottom of the display.

2Enter a channel number ([1] to [5]) corresponding to your desired PM channel.

•The settings stored in the PM channel are recalled.

•The selected channel number appears on the display.

•When selecting [OFF], the PM channels turn off.

Image 48

Contents 144/440 MHz FM Dual Bander 144/430 MHz FM Dual BanderFeatures This transceiver has the following main featuresThank You Writing Conventions Followed in this ManualWhen Condensation Occurs Inside the Transceiver One or more of the following statements may be applicablePrecautions Contents Using Ctcss Ctcss Frequency ID Using DCS DCS Code IDManual Dialing Automatic dialer Dtmf Key Lock VGS-1 Optional Voice Guide & Storage UnitOptions Supplied Accessories Mobile InstallationPreparation Part Number QuantityPower Cable Connection Mobile OperationFixed Station Operation Located on the DC connector Supplied DC power cableReplacing Fuses Fuse Location Fuse Current RatingAntenna Connection Front Panel Orientation Accessory Connections External SpeakersMicrophone Getting Acquainted Front PanelREV LOWPF1 0PF2Indicator Description DisplayAppears while accessing the Menu Rear Panel Sub-PanelMicrophone MC-59 Switching the Power ON/ OFF Adjusting the VolumePress the switch to switch the transceiver on Press the switch again to switch the transceiver OFFAdjusting the Squelch Selecting a BandBand a left Band SEL control Band B right Band SEL control Selecting Dual band mode/ single band Mode Selecting a frequency band Frequency rangesSelecting an Operating mode VFO ModeMemory Channel Mode Call Channel Mode Press Call to enter Call Channel modeWhen you finish speaking, release the PTT switch TransmittingMenu Mode Menu AccessMenu Configuration Press F, Tuning control to access the MenuANN.SPD DT.SPD MIC.LCK Rotate the Tuning control to select your desired character Press the Tuning control to set the selected characterCharacter Entry Repeat steps 2 and 3 to enter the remaining charactersMicrophone Keypad Character Entry Key Character Display with each press of the keyRepeater Access Operating Through RepeatersSelecting an Offset Direction Selecting an Offset Frequency Activating the Tone FunctionRotate the Tuning control to select your desired frequency Selecting a Tone FrequencyPress F, Tone FrequencyAutomatic Repeater Offset K and E Types Only Transmitting a 1750 Hz Tone Reverse FunctionAutomatic Simplex Checker ASC Tone Frequency ID Press F, Tone 1s to run the Tone Frequency ID scanMemory Channels Simplex & Repeater or ODD-SPLIT Memory CHANNEL?Parameter Simplex Odd-split Storing Simplex and Standard Repeater Frequencies Storing Odd-Split Repeater FrequenciesCall Channel Memory Simplex Recalling a Memory Channel Call Channel Memory Odd-SplitMemory Recall Method Turn the transceiver power OFF Press MR + Power onPress the Tuning control to clear the Memory channel Clearing a Memory ChannelSwitching the Memory Name/ Frequency Display Memory-TO-VFO TRansferChannel Display FUnction Press F, VFOKey Name KEY KEY 1s While KEY +Programmable Memory PM Application Examples Storing Data in PM Channels Recalling PM ChannelsPress F, PM PM Channel Reset Press F + Power onPress the Tuning control again to reset the PM channels Auto PM Channel storeScan Scan Type Scan RangeSelecting a Scan Resume Method VFO ScanMemory Scan Locking Out a Memory ChannelPress MR 1s To quit Memory Scan, press MR againTo quit Group Scan, press the Tuning control again Group ScanMemory Group Link Memory Group Channel RangeSetting Scan Limits Program ScanPress VFO Using Program Scan To quit Program Scan, press VFO againTo quit MHz Scan, press the Tuning control again MHz ScanCall Scan To quit Call Scan, press Call againUsing Ctcss Continuous Tone Coded Squelch System CtcssPress Enter again to complete the setting Ctcss FREQuency ID Press F, Tone 1sUsing DCS Rotate the Tuning control to select your desired DCS codeDigital Coded Squelch DCS DCS Code DCS Code ID Dual Tone MULTI-FREQUENCY Dtmf Manual DialingDtmf Hold 1209 1336 1447 1633 697 770 852 941Automatic Dialer Storing a Dtmf Code in MemoryTransmitting Stored Dtmf Codes Selecting a Transmit SpeedDtmf Key Lock Selecting a Pause DurationWhat is EchoLink? Storing EchoLink memoryTransmitting EchoLink Memory Setting Up EchoLink Sysop Mode EchoLink Sysop Mode on TM-V71EchoLink Sysop Mode OFF TM-V71 TxD RxDPOWER-ON Message Auxiliary FunctionsDisplay Brightness Auto Display BrightnessKey Lock Backlight ColorMicrophone Key Lock To turn Key Lock on or OFF, press F 1sBeep Volume Key BeepProgrammable VFO Changing the Frequency Step Size Programmable Function Keys Transceiver Front PanelMicrophone Keys Automatic Power OFF APO Frequency Direct EntryMeter Squelch Advanced Intercept Point AIPSquelch Hang Time Switching FM/AM Mode Beat ShiftSpeaker Mute Selecting an Output Power TIME-OUT Timer TOTMute Hang Time External Speaker Configuration SetupMasking a Band Speaker Band OutputDisplay Partition Bar Weather Alert K Type Models Only Weather ChannelChannel No Memory Name LocationPower On Password Enter your passwordVGS-1 Optional Voice Guide & Storage Unit Voice AnnouncementsOperation Announcement Current frequency/codeAuto Voice Announcement Volume Voice Announcement LanguageVoice Announcement Speed Voice Recorder Voice MemosConversation Recorder Playback Playback RepeatPlayback Repeat Interval Press Tone + Power on CROSS-BAND/ LOCKED-BAND Operation K Type Models onlyRepeater Hold Repeater IDEntering your Repeater ID Data terminal pins Packet OperationData Band Data Terminal SpeedSQC Output Setting PC Port SpeedWireless Operation K Type Models only PreparationOperation Dtmf Command Control OperationTransceiver Reset Menu Mode Using the MCP-2A Software Using the MCP-2A software, you canOptions Memory control program MCP-2AConnecting the PG-5G/ PG-5H interface cables Installing the DFK-3D panel kitInstalling the Sub-Panel PC terminal pinsInstalling the Panel Bracket Clean and dry the installation locationConnect the supplied sub-panel to Operation panelConnecting the PG-5F extension cable Connecting Using a Single Extension KitConnecting Using Two Extension Kits Installing the Line FilterInstalling the VGS-1 Unit Insert the VGS-1 unit into the connector On the transceiverFrom the remaining cushions, select Maintenance ServiceService Note CleaningTroubleshooting Problem Probable Cause Corrective ActionUP/DWN Specifications GeneralType M4 Type Transmitter Receiver