Lexicon DD-8 manual Specifications

Page 15

DD-8Power Amplifiers

APPENDIX

Specifications

Specifications are subject to change without notice.

Output Power:

125W RMS per channel into 8 ohms from 20Hz – 20kHz

 

 

Frequency Response:

20Hz - 20kHz +0dB/–1.5dB

 

 

Total Harmonic Distortion (THD):

Less than 0.05% at full rated power 20Hz - 20kHz

 

 

Signal-to-Noise Ratio:

< –105dB below rated full power A-weighted

 

 

Crosstalk:

< –70dB @ 1kHz

 

 

Input Sensitivity:

1.12 volts for 125W out into 8 ohms

 

 

Gain:

29dB

 

 

Input Impedance:

100K ohms typical

 

 

Trigger Input:

5V minimum – 15V maximum DC

 

 

Dimensions (H x W x D):

2.1” (w/ feet) / 1.7” (w/out feet) x 17.3” x 14.9”

 

5.4 cm (w/ feet) / 4.5cm (w/out feet) x 43.8 cm x 37.8 cm

 

 

Weight:

9.2 lbs (4.2 kg)

 

 

Power Requirements:

100 - 240VAC 50/60Hz 190W

 

 

Operation Manual

15

Image 15
Contents DD-8 Power Amplifier Watch for These Symbols Important Safety InstructionsDeclaration of Conformity Documentation Conventions Following symbols are used in this documentHighlights Getting StartedInstallation Options Installation ConsiderationsStandby Button Channel Status Indicator LED’sBasic Operation Front PanelBack Panel Bus OutputBus Input Local/Bus Selection Local InputsOutput Level Controls Stereo/Mono SelectionPower Save On/Off Signal Sense On/OffSpeaker Outputs Trigger In/Out To install a trigger cableAC Main Power Connector Troubleshooting Troubleshooting and MaintenanceMaintenance Humming sound is present in the audioIf all else fails… Specifications This page Intentionally Left Blank DD-8 Leistungsverstärker Bedienungsanleitung Dokumentationskonventionen Diesem Dokument werden die folgenden Symbole verwendetBesondere Merkmale Erste SchritteInstallationsmöglichkeiten InstallationsvoraussetzungenLED-Anzeigen für den Status der Kanäle BetriebVorderseite Standby-TasteRückseite Bus-AusgangBus-Eingang Lokale Eingänge AusgangspegelsteuerungStereo-Mono-Auswahl Lokal-Bus-Auswahl LautsprecherausgängeEnergiesparzustand ein/aus Trigger-Eingang und -Ausgang Signalsensor ein/ausNetzstromanschluss So installieren Sie ein Trigger-KabelDie Tonwiedergabe wird plötzlich unterbrochen Fehlerbehebung und WartungFehlerbehebung Der Verstärker lässt sich nicht einschaltenWartung Die Tonwiedergabe enthält ein summendes GeräuschWenn das alles nicht hilft … Spezifikationen Amplificador de potencia DD-8 Manual de funcionamiento En este documento se utilizan los siguientes símbolos Convenciones de la documentaciónCaracterísticas destacables IntroducciónOpciones de instalación Consideraciones sobre la instalaciónIndicadores LED del estado del canal Funcionamiento básicoPanel frontal Botón de esperaPanel posterior Salida de busEntrada de bus Entradas locales Controles del nivel de salidaSelección Estéreo/Mono Selección Local/Bus Salidas de altavozAhorro de energía On/Off Entrada/salida de disparador Detección de señal On/OffConector principal de alimentación de CA Para instalar un cable de disparadorLos niveles de audio difieren entre los canales Resolución de problemas y mantenimientoResolución de problemas El amplificador no se enciendeMantenimiento El audio presenta un zumbidoSi todo lo demás falla… Especificaciones Amplificateur de puissance DD-8 Mode demploi Conventions utilisées dans le présent document Les symboles suivants sont utilisés dans ce documentPoints essentiels DémarrageOptions d’installation Considérations relatives à l’installationDEL indiquant l’état des canaux Fonctionnement de baseFaçade avant Bouton de mise en veillePanneau arrière Sortie BusEntrée Bus Sélection Local/Bus Entrées localesContrôles du niveau de sortie Sélection Stéréo/MonoSorties de haut-parleurs Activation/désactivation de la détection de signal10. Déclencheur activé/désactivé Pour installer un câble de déclencheurConnecteur d’alimentation principale secteur Les niveaux audio varient selon les canaux Dépannage et maintenanceDépannage ’amplificateur ne se met pas sous tensionSi le problème persiste… Un bourdonnement se fait entendre sur l’audioRéponse en fréquence Rapport signal/bruitCaractéristiques Puissance de sortieHow do State Laws Relate to this Warranty? What is the Duration of this Warranty?What is Covered? How is Service Obtained?This page Intentionally Left Blank Product Registration This page Intentionally Left Blank DD-8Power Amplifiers
Related manuals
Manual 16 pages 47.89 Kb

DD-8 specifications

The Lexicon DD-8 is a powerful digital delay processor that has gained recognition among audio engineers and musicians for its versatility and high-quality sound processing capabilities. Renowned for its advanced features and technologies, the DD-8 offers unmatched performance in both studio and live settings.

One of the main features of the Lexicon DD-8 is its ability to deliver studio-quality delays with unprecedented precision. The device is equipped with multiple delay algorithms that cater to various audio applications, including classic analog-style delays, digital delays, and more complex modulation effects. Each algorithm is designed to produce a richness of sound that enhances any audio mix, making it an essential tool for creative sound design.

The DD-8 stands out with its comprehensive user interface. It incorporates a bright, easy-to-read display and intuitive controls, which allow users to navigate through parameters effortlessly. This includes the ability to adjust delay times, feedback settings, and modulation depths in real time. Additionally, the DD-8 features a dual-path design, enabling users to apply different delay settings to two separate channels simultaneously, providing greater flexibility for stereo effects.

In terms of connectivity, the DD-8 excels with its robust input and output options. It supports both analog and digital connections, including S/PDIF and AES/EBU formats, ensuring compatibility with a wide range of audio equipment. This makes it an ideal choice for both professional studios and live performance environments.

One of the standout technologies in the DD-8 is its sophisticated DSP (Digital Signal Processing) engine. This powerful processing unit allows for a high degree of customization and control over the audio signal, enabling users to achieve complex soundscapes. The engine also ensures minimal latency, making it suitable for real-time applications without compromising sound quality.

Furthermore, the Lexicon DD-8 is built with high-quality components that contribute to its reliability and durability. Whether used in a studio or on stage, the unit's rugged construction ensures it can withstand the rigors of frequent transport and use.

In summary, the Lexicon DD-8 is a versatile and powerful digital delay processor that combines advanced sound processing capabilities with an intuitive user interface. Its rich feature set, combined with high-quality sound and dependable performance, makes it a valuable asset for any audio professional seeking to elevate their audio productions. Whether for music production, live sound, or creative sound exploration, the DD-8 remains a top choice in the realm of audio processing technology.