Selecting the Band
The band (BAND1 through BAND5) changes each time [BAND] is touched.
The active bar and the variable range of the center frequency move according to the band.
•Touching outside the variable range for a selected band moves the active bar to a band where the touched position can be adjusted.
Setting the Bandwidth
The bandwidth changes each time [Q] is touched.
Adjusting the Level/Frequency Directly
Move to a desired position by touching the active point and change the setting contents. Or, move the active point to the desired position by touching where you wish to move it.
•Downloading is stopped, and the setting contents (created before stopping by touching [CANCEL] in the display during the download, or operating the connected audio processor) are displayed.
•Loading time may take longer depending on the setting content. This is not a malfunction.
9 Touch [RETURN] to return to the previous screen.
•When the speaker is set to the “OFF” mode, the parametric equalizer for that speaker cannot be set. Refer to “Setting the Speakers” (page 46).
•It is not possible to adjust the frequencies of adjacent bands within 7 steps.
•Check the playable frequency ranges of the connected speakers before making the equalizer adjustments. If the speaker’s playable frequency range is 55 Hz to 30 kHz, for example, adjusting the 40 Hz or 20 Hz band has no effect. Additionally, you may overload and damage the speakers.
•When the parametric EQ is adjusted, the adjustment for graphic EQ becomes ineffective.
Setting Bass Sound Control
1 Make sure that the defeat is turned off (page
The SETUP selection screen is displayed.
3 Touch
The
4 Touch [ 
] of A.PROCESSOR.
The A.PROC list is displayed.
5 Touch [ 
] of BASS SOUND CONT.
The Bass Sound Cont. screen appears.
Setting Bass Compressor
You can adjust the sound of low frequencies as desired.
6 Touch [
] or [
] of BASS COMP. to select the desired mode.
Bass sound is emphasized more as the mode is sequentially switched as MODE1 
2 
3, offering you vivid low frequencies.
Select OFF when the setting is not necessary.
Touch [RETURN] to return to the previous screen.
Setting Bass Focus
Using the previously specified delay number (time difference) allows you to set a time difference between the
6 Set the delay number in the front and rear, and on the right and left of the desired speaker by touching the respective [
] or [
] button.
•Any setting in Bass Focus is applied in time correction, too.
•Touch [RETURN] to return to the previous screen.
Speaker Setup
The
Check the playable frequency range of the speakers (not including the subwoofer) before performing this operation to verify whether the speakers can play low frequencies (of about 80 Hz or less).
•Avoid stopping, pausing, switching the disc, cueing,
1 Check that Defeat mode is off.
2 Touch [SETUP] on the main source screen.
The SETUP selection screen appears.
3 Touch
The
4 Touch [ 
] of A.PROCESSOR.
The A.PROC list screen appears.
5 Touch [ 
] of SPEAKER SETUP.
The adjusting screen of SPEAKER SETUP appears.
6 Select the speaker characteristic by touching [
], [
] or [ON], [OFF] of the desired speaker setting.
OFF*1: When no speaker is connected.
SMALL: When a speaker that cannot play low frequencies (80 Hz or less) is connected.
LARGE*2: When a speaker that can play low frequencies (80 Hz or less) is connected.
*1 | It is not possible to set the front speakers to “OFF”. |
*2 | If the front speakers are set to “SMALL”, the rear and |
| center speakers cannot be set to “LARGE”. |
•If the center speaker is turned “OFF,” the center channel’s audio signals are added to the audio signals output from the front speakers.
•If you set the speaker response to “OFF,” also set the speaker setting to “OFF.” (page 46)
•Perform the setup for all the speakers (“Front,” “Center,” “Rear” and “Subwoofer”). If not, the sound may not be balanced.
•When center is set to “OFF”, the setting is ineffective even if center is set with this function.
•Through changing the settings on each speaker, a change in the output of the other speakers may occur due to the setting requirements.
•When using the PRO LOGIC II, if the rear speaker is set to “LARGE”, then there will be no output from the subwoofer.