Alpine IVA-D310 owner manual 73-EN, Installing the Monitor Installation Location, Removal

Page 75

Installation

Installing the Monitor

Installation Location

Before deciding on the mounting location, check that opening and closing the display will not hamper gear shifting in that position.

•Install at an angle of within 30 degrees from the horizontal.

•The monitor’s angle is set to 90 degrees at the factory. Depending on the car, the monitor may hit the dashboard when opened. The monitor’s angle can be adjusted and stored in memory so that the monitor will not hit the dashboard when opening. For adjusting the monitor, refer to “Adjusting the Monitor Viewing Angle” on page 11. Even when the vehicle’s battery power is removed, the adjusted monitor angle remains stored in memory.

1

Dashboard

Mounting Bracket

Mounting Sleeve

(Included)

(Included)

 

 

IVA-D310

Flush head Screws (M4 ⋅ 3) (Included)

Slide the mounting sleeve into the dashboard. Install the supplied bracket on the monitor.

•Make sure to use the supplied Flush head screw (M4 ⋅ 3) to install the monitor.

If you use another screw to install the monitor, it may cause a malfunction.

2

Screw

Hex Nut (M5)

Bolt Stud

IVA-D310

Meatal Mounting

Strap

Ground

Lead

Front Frame

Chassis(Included)

Wider edge should face down.

Reinforce the monitor unit with a metal mounting strap (not supplied). Secure the ground lead of the unit to a clean metal spot using a screw ( ) already attached to the vehicle’s chassis.

•For the screw marked , use an appropriate screw for the chosen mounting location.

Connect each input lead coming from an amplifier or equalizer to the corresponding output lead coming from the left rear of the IVA-D310. Connect all other leads of the IVA- D310 according to details described in the Connections section.

3

Lock Pin

Slide the IVA-D310 into the dashboard. When the unit is in place, make sure the locking pins are fully seated in the down position. This can be done by pressing firmly in on the unit while pushing the locking pin down with a small screwdriver. This ensures that the unit is properly locked and will not accidentally come out from the dashboard. Install the supplied Front Frame.

Removal

1.Use a small screwdriver (or similar tool) to push the locking pins to the “up” position (see Step 3). As each pin is unlocked, gently pull out on the unit to make sure it does not re-lock before unlocking the second pin.

2.Pull the unit out, keeping it unlocked as you do so.

<JAPANESE CAR >

To install using the vehicle’s standard bracket.

Flush Head Screws (M4 ⋅ 3)

Ground Lead

(Included)

 

 

IVA-D310

Mounting Bracket

•Make sure to use the supplied flush head screw (M4 ⋅ 3) to install the monitor.

If you use another screw to install the monitor, it may cause a

malfunction. However, only if you cannot install with the flush head screws (M4 ⋅ 3), use the supplied screw (M4 ⋅ 6).

73-EN

Page 74 Page 76
Image 75
Page 74 Page 76
Contents IVA-D310 CHA-1214CHM-S630 CHA-S634Contents Operating Instructions Monitor Setting Navigation System Optional Installation Connections Operating Instructions Maintenance Pictures Mark logo Recorded Disc size MaxDisc VideoALL Disc terminology 10-EN Getting StartedLocation of Controls Detaching and Attaching the Front PanelOpening/Closing the Monitor Turning Power On or OffAdjusting the Monitor Viewing Angle Initial System Start-UpMoving the Monitor to be Flat Adjusting the VolumeLowering Volume Quickly How to view the Display13-EN Touch a desired setup menuShortcut Screen Displaying the Numeric Keypad Input Screen14-EN RadioListening to the Radio Dual-Screen Display15-EN Manual Storing of Station PresetsAutomatic Memory of Station Presets Tuning to Preset StationsSelecting Folders concerning MP3/ WMA PlaybackRepeat Play X. Random Play17-EN About MP3/WMATerminology DVD/Video CDPlaying DVD/Video CD 18-ENDirect Menu Operations DVD only To display the DVD mode screenIf a menu screen appears 19-ENFast-forwarding/Fast-reversing Turning the PBC Function on or OFF Video CD onlyStopping Playback PRE Stop Stopping PlaybackForward/reverse frame-by-frame Playback Playing Still Frames PausingFinding the Beginnings of Chapters or Tracks Chapter/Track/Title Repeat Playback22-EN Switching the Audio TracksSwitching the Angle DVD only Searching Directly by Chapter or Track Number23-EN Other Useful FeaturesAdjusting the Audio Switching from the disc menu24-EN Touch on the function guide while in the CD or MP3/WMA modeInternal CD player mode Search Function25-EN Switching Display ModesSwitching the function of the remote sensor Rear Entertainment FunctionSetting the Visual Effect Switching the Visual Source Only Simultaneous FunctionBlackout Mode On and Off Setting VisualizerDVD Setup Operation Monitor SettingSetup Monitor Setting OperationChanging the Country Code Setting Setting of the Menu LanguageSetting of the Audio Language Setting of the Subtitle Language29-EN Setting the Rating Level Parental LockChanging the Digital Output Setting Touch the input screen to enter a new 4-digit password30-EN 32kbps~320kbpsWindows Touch of General Setup General Setup OperationSetting the Downmix Mode Setting the TV Screen SettingSetting the Sound Quality of the Tuner Setting the TimeSetting Daylight Saving Time Setting the ScrollSetting the Navigation Mode System Setup OperationSetting the External Device Interrupt Mode Setting the Interrupt Icon DisplaySetting of the External Monitor Output Setting the Visualizer Mode DisplaySetting the AUX Mode Adjusting the External Input Audio LevelTouch of Display Setup Display Setup OperationSetting the Digital Output Setting the Brightness of the BacklightingSetting the Font Type Adjusting the Minimum Level of BacklightSwitching Background Textures Setting Automatic Background Textures37-EN Setting the MX modeSetting the Bass Engine PersonalizeSelecting Bass Max EQ mode Maker’s setting Adjusting and Storing/Recalling the Parametric EQ38-EN Adjustment and Storing/Recalling of Time Correction About the Time Correction39-EN Adjusting and Storing/Recalling the Bass Focus Setting item Bass Focus Setting contents40-EN 41-EN Adjustment and Storing/Recalling of the Built-in CrossoverSubwoofer On and Off Visual EQ Setting Operation43-EN Adjusting Picture QualityData Downloading Storing Visual EQ44-EN AMP Link Lock Function45-EN Adjustment Procedure for Dolby Surround46-EN Setting the SpeakersSet MX Mode of the External Audio Processor Over AdjustmentPerforming Time Correction Manually TCR Adjust the crossover to your preferenceAdjusting Level/Cut-off Frequency Directly Check that Defeat mode is offPhase Switching Graphic Equalizer Adjustments48-EN 49-EN Parametric Equalizer AdjustmentsSetting Bass Focus Setting Bass Sound ControlSpeaker Setup Setting Bass CompressorAdjusting the DVD Level Setting of Dolby 5.1ch52-EN Storing Settings in the MemoryGetting out the Preset Memory Using the Pro Logic II Mode53-EN Linear PCM SettingSwitching the Navigation Screen Optional Navigation System OptionalControlling CD Changer Optional Auxiliary Device OptionalChanger Optional Operating Auxiliary Devices Optional55-EN HDD Player Operation OptionalMulti-Changer Selection Optional Listening to Music of HDDChanging the Display Tuning in to Categorized ProgramsSAT Radio Receiver Optional Receiving Channels with the SAT Receiver OptionalSelecting the Channel directly Storing Channel PresetsReceiving Stored Channels Displaying the Category/Channel Name Title ListSearching by artist name IPod OptionalSearching for a desired Song Searching by Playlist59-EN About Subdisplay IndicationsAbout Subdisplay Indications Random Play Shuffle M.I.XRemote Control Controls on Remote Control60-EN 61-EN When Using the Remote Control62-EN Battery ReplacementInformation About DVDs63-EN TerminologyList of Language Codes 64-ENFor details, see 65-EN List of Country Codes66-EN 67-EN Case of Difficulty68-EN 69-EN Indication for DVD/Video CDIndication for CD changer 70-EN Indication for SAT Receiver ModeChassis Size Tuner section Specifications71-EN Chassis Size Monitor section72-EN Installation and Connections73-EN InstallationInstalling the Monitor Installation Location To install using the vehicle’s standard bracket74-EN Installing the Tuner BoxWhen mounting with Velcro fasteners Installing the DC/DC ConverterParking Brake Lead Connection Connection Diagram of Spst Switch Sold SeparatelyIf the ACC power supply is not available 75-EN76-EN Connections IVA-D310 Wiring Diagram77-EN 78-EN System ExampleAUX Video Input AUX1 Terminal Digital Output Terminal Ai-NET ConnectorTo Ai-NET Connector Gray To Ai-NET Connector Black 79-EN80-EN 81-EN To Ai-NET Connector Black To Ai-NET Connector Gray
Top Page Image Contents