Blaupunkt TCM 127 Traffic programme station reception with RDS-EON, Beep tone

Page 21

Traffic programme station reception with RDS-EON

The abbreviation “EON” stands for En- hanced Other Networks which means that information is exchanged between the ra- dio stations belonging to the same broad- casting network.

Many FM broadcasters provide traffic mes- sages for their service area at regular inter- vals.

All traffic programme stations transmit a special carrier signal along with their pro- grammes, which is decoded by your car ra- dio. If this signal is identified, “TP” will ap- pear in the display (Traffic Programme).

In addition to these, there are also stations which do not actually transmit traffic pro- grammes themselves, but by using RDS- EON it is possible to receive the traffic mes- sages broadcast by another traffic pro- gramme station in the same radio network.

If you wish to have the priority for traffic an- nouncements activated while listening to one of these stations (e.g. NDR3), “TA” must appear in the display.

If a traffic announcement is broadcast, the radio will automatically switch to the linked traffic programme station (in this case, NDR2) for the duration of the message and return to the original programme (NDR3) afterwards.

Switching traffic announcement priority on/off

If the priority for traffic announcement pro- grammes is activated, “TA” will light up in the display.

To switch the priority on or off:

•Press TA.

If you press TA while a message is being broadcast, this message will be interrupted.

The unit will then switch back to its previous status. The priority for all other traffic mes- sages will remain active.

Please note that several buttons have no function while traffic announcements are broadcast.

Adjusting the volume for traffic announcements and the beep tone

Although this volume was preset at the fac- tory, you can alter it using the DSC function (see “Programming with DSC – TA VOL- UME”).

Beep tone

When a traffic programme station is activat- ed (“TA” in the display), you will hear a beep tone after approximately 30 seconds if you leave the reception area of the traffic pro- gramme station you are currently tuned into.

You will also hear this beep if you press a station preset button for a radio station which does not broadcast the TP signal.

Switching off the beep tone

a)Tune into another station providing traffic information:

•Press the rocker switch or

•press a preset button for a radio station which has a traffic pro- gramme station allocated to it.

or

b)Switch off the priority for traffic an- nouncements:

•Press TA.

“TA” will disappear from the dis- play.

Automatic seek tuning start

(tape and CD changer operation)

If you leave the reception area of the cur- rent traffic programme station while listen- ing to a tape or CD, the system will auto- matically start searching for a new TA pro- gramme.

RadioDEUTSCH

ENGLISHTelefon

TelephoneRadio

83

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Amsterdam TCM Remote control RCT 07 optional Contents Radio, Cassette, Changer Option Contents Telephone Safety information Safety standardsImportant information General informationInstallation Using the telephone in critical areasEmergency calls Remote control AccessoriesChanger HandsetBasic information KeyCard and SIM cardStarting up the Radiophone Second KeyCard/SIM cardTrain KeyCard/SIM cards Removing the KeyCard/SIM cardSelecting the language for the display Never forcibly pull out the card! You may destroy itDisplaying the radio pass data DSC learn modeOptical warning of anti-theft protection Care of your KeyCard/SIM-CardSwitching the unit on/off with the KeyCard On/off VolumeSwitching the unit on/off via the ig- nition Switching the radio on when the ig- nition is switched offTS / BND SRC SourceStoring radio stations Cassette loading slotRecalling stored radio stations -Se AF / #Display = MIXRadio operation a Cassette operation Changer operation optionalTape operation Flashing card tongueStop this function by pressing or the opposite button Additional settings possible with AUD Additional rocker switch functionsDSC mode C Corresponding function must be activatedAF Alternative Frequency Audio modeREG regional programme Radio, tape deck, CD changer optional, auxiliary sourceSeek tuning Station tuningManual tuning with Selecting a wavebandStoring radio stations Scrolling through the broadcast- ing networks FM onlySelecting the seek-tuning sensi- tivity Switching from stereo to mono FM onlyRecalling stored radio stations Automatic seek tuning start Switching traffic announcement priority on/offSwitching off the beep tone Traffic programme station reception with RDS-EONOperating the cassette deck Tape equalisation Dolby B NRCare instructions Switching CD changer operation on CD changer operation optionalSelecting the CD and the track Select CancelAlter StoreTo make a note of the new code Loud 1 minimum boost Loud 6 maximum boostMusic/voice is switched off Tone setting for voice programs ranges between Level 0RAD. Monitor Radio Monitor With this function you can deterYou can choose among the fol- lowing operating modes Remove menu items All of the menu items are availa- bleEnd DSC programming/save changes Overview of the DSC default settingsPage Telephone operation PIN code Operating the telephoneInserting the SIM card/ entering your PIN code Reactivating the SIM cardMaking your first telephone call GSM emergency callsDo not hang up until you are told to do so Volume Quick reference for using the telephoneOn/Off Selection buttonsTo switch back to the telephone mode Press briefly Enter PIN code Network search Setup menu/Call menuDisplays Radio menu Telephone-book menu@ Rocker switch Switching to telephone mode Using the telephoneGSM network service area Dialling a telephone numberRedial function Answering/ending a call Call waiting 2nd callerBroker’s call/hold Making telephone calls using the handset special accessory Setting up a conference callConference calls 103 Phone book menuHow to enter a name/text Finding an entry by name Prevent access Show my phone numberCheck capacity Add entry Finding an entry by positionAltering, deleting, moving or copying the entry Programming with DSC Telephone Press CL, the altered setting will not be storedStore/confirm End DSCProgramming in the setup menu Select the setup menu by pressing109 Hands-free volume Automatic answer Ringing tone volumeAutomatic redial Operating mode Handset volumeSMS tone Ringing toneMy phone number Call meter formatAudible call timer PIN codeSet charge parameters Following settings will be deleted Alter access codeExternal alarm Be sure to make a note of the new code if you change itHands-free channel Overview of the basic factory settings in the set-up menuHands-free operation is possible on all four channels TA during callPress CL, the new setting will not be stored Programming in the Call Menu115 Selecting the message Call mailbox Received SMS messagesReading messages Clearing messagesSending SMS messages Calling the sender or another telephoneNetwork selection Which operates in numbered channels Cell BroadcastSages Available channels from your network OperatorCall meters Call forwardingCall barring You can only call the one-touch dial Phone lockOne-touch dial only To 9 and the SIM card Speed/touch dial onlyClosed user group Overview of the basic factory settings in the call menuGlossary Tuner SpecificationsTelephone Tape deck01 80 / 5 25 56 Blaupunkt telephone help lineBosch Gruppe
Top Page Image Contents