Landice 8700 manual Series

Page 1

1

111 Canfield Avenue Randolph, New Jersey 07869 1-800-LANDICE FAX 973-927-0630

8700-Series

Home and Commercial Treadmill Diagnostic and Service Manual 2001

This guide covers all 8700 series treadmills manufactured from

1993 – 2000.

HOME TREADMILLS – 8700 SPRINT 1-4 / PRG / SST

NOTE: Early HOME treadmills listed as: 8700R & 8700P are the same as the LTD models. The only difference was the warranty coverage.

LTD / 110V UNITS – 8700R (REGILAR NO PROGRAMS) / P (WITH PROGRAMS) / PT1 / PT2 CLUB / 220V UNITS – 8700R (REGILAR NO PROGRAMS) / P (WITH PROGRAMS) / PT1 / PT2

Version M/C.1

For Technical Service Call 1-(800)-LANDICE

Image 1
Contents Series Introduction InstallationParts Identification Servicing Landice TreadmillsHow to Use this Manual Parts Landice Warranty and PoliciesTreadmill Parts Service LaborRecommended tools for servicing Landice treadmills Important Operating Safety Instructions Grounding Instructions 200 250 Volt Treadmills 15 Amp dedicated line Standard Membrane Settings Used In HomeSprint Membrane Production Time FrameMembrane 8700 EP/PT MembraneSST Membrane 8700 PT2 MembraneSprint Faceplate Programmable MembraneParts Identification Em brane Panel-SPRINT3/4 70190 Side FR AM E XL Comercial Motor PAN Components Commercial Lower Wiring Schematic LED light emitting diode configurations SCR lower board Page Home SST VFX, PRG VFX, Sprint VFX Closed Loop Speed Sensor 8700 SST, PRG and Sprint VFX Treadmill LED Lights on PWM LED light emitting diode configurations Relay Board Sprint 3 treadmills have push button controls 8700 SST, PRG and Sprint 3, NON VFX TreadmillSprint Sprint 1 Lower Wiring Schematic Sprint 1&2 Upper Wiring Schematic Definitions Side Frame Covers Safety LanyardIR Potentiometer Membrane PanelTreadbelt Upper Wire HarnessUpper Display Board Uprights VFX SystemVDC Power Supply Testing ComponentsFaceplate Elevation MotorPWM Motor Control SCR Motor ControlUpper Display Board Relay BoardSymptom Treadmill slows down when user steps onto treadbelt Common SymptomsSymptom Treadmill speed is erratic and/or surges IR Potentiometer ADJUSTMENTS, PWM only = 8.0rpm = 9.3rpmPower Cord Line Cord Removal and Replacement of ComponentsRelay Board Sprint 4/PRG/SST Closed Loop only VDC Transformer Replacement Home Treadmills onlyUnplug treadmill Drive Motor BrushesRemove Elevation Motor Install new Elevation MotorTo calibrate the potentiometer To Enter Diagnostic ModeDeck REMOVAL/DECK Reversal UN Plug Treadmill Treadbelt Unplug TreadmillTake Up Roller/ Rear Roller Drive Roller/Front Roller Noises Page Drive Motors Visual CluesElectronic Boards Elevation MotorVoltage Tests Error Codes Diagnostic GuideSeries Treadmill Configuration Mode Treadbelt Tracking Treadbelt TRACKING, Tensioning and MaintenanceTreadbelt Tensioning Drive Belt Tensioning Unplug TreadmillYES Drive motor is good. Proceed to Step YES Prog Enter Pause Start Display Fast Slow Down Button CodeYES Elevation Potentiometer Calibration Series Home Treadmill Symptom Any found? Is speed control wiring OK? SymptomIs it out of position? Any found?Is the motor wiring OK? UP Down Clockwise Sprint 8700 PRG 8700 SST Page BELT-RELAY Sprint Symptom Applies to Sprint 2 Only Treadmill is switched on? Applies to Sprint 2 Only See Sprint 2 Wiring Schematic for Speed POT Settings Elevation system will need to Tracking and Tensioning Check Drive Belt tension Make Sure Treadmill is Level Recommended MaintenanceDrive Roller Alignment ExampleHow to lubricate When to lubricateService CHECK-LIST Institutional drive motor maintenanceIndex 5V LED Drive Motor Brushes LED Lights Safety Lanyard Uprights Frame