Landice 8700 manual Landice Warranty and Policies, Parts

Page 4

4

Landice Warranty and Policies

PARTS

Our policy requires that all defective parts be returned to Landice. All warranty parts will be billed to the dealer at dealer cost. Landice will credit this invoice upon receipt of defective parts. Landice will pay the freight to send out any defective parts. It is the dealer's responsibility to pay the freight to return the defective parts to Landice. If the defective parts are not returned within 30 days, payment of invoice is expected in full.

LABOR

Landice will reimburse the selling dealer according to our flat rate labor schedule. If you are a service provider for Landice and do not sell our product, you have the option of billing us direct or you can bill the dealer your providing service for. Generally, if our capped rate does not cover your labor charge you would bill the selling dealer. The current rate is $30.00 per hour and is capped at a maximum of one hour labor and one hour travel per treadmill failure. Diagnostic

and return trips are not covered. Note that treadbelt tracking, treadbelt/drivebelt tensioning, blown fuses, and set-up procedures are not covered by this warranty. Set-Up Includes: Assembly, adjusting treadbelt and drive belt (if needed), walking the treadbelt and deck wax in and performing any additional adjustments that may have been upset during shipping.

The dealer must call for a service authorization number prior to performing any service to verify the treadmill is under labor warranty. It is advisable to call Landice from the treadmill location to successfully diagnose the problem. This will ensure that the correct part will be shipped out the first time. Labor claim forms must be submitted within three months from the date service was performed. Labor claim forms must be completely filled out and have the Landice authorization number at the top.

FLOOR MODELS

The following warranty applies to floor models and dealer stock.

If the dealer sells a treadmill to a customer within one year of its purchase from Landice, the warranty period will be extended to start from the date of sale to the customer.

If a treadmill is over 1 year old when sold to a customer, the remainder of the parts warranty will be honored from the date of shipment and 1 year labor.

Image 4
Contents Series Installation IntroductionParts Identification Servicing Landice TreadmillsHow to Use this Manual Landice Warranty and Policies PartsService Labor Treadmill PartsRecommended tools for servicing Landice treadmills Important Operating Safety Instructions Grounding Instructions 200 250 Volt Treadmills 15 Amp dedicated line Settings Used In Home Standard MembraneSprint Membrane Production Time Frame8700 EP/PT Membrane Membrane8700 PT2 Membrane SST MembraneProgrammable Membrane Sprint FaceplateParts Identification Em brane Panel-SPRINT3/4 70190 Side FR AM E XL Comercial Motor PAN Components Commercial Lower Wiring Schematic LED light emitting diode configurations SCR lower board Page Home SST VFX, PRG VFX, Sprint VFX Closed Loop Speed Sensor 8700 SST, PRG and Sprint VFX Treadmill LED Lights on PWM LED light emitting diode configurations Relay Board 8700 SST, PRG and Sprint 3, NON VFX Treadmill Sprint 3 treadmills have push button controlsSprint Sprint 1 Lower Wiring Schematic Sprint 1&2 Upper Wiring Schematic Definitions Safety Lanyard Side Frame CoversIR Potentiometer Membrane PanelUpper Wire Harness TreadbeltUpper Display Board Uprights VFX SystemTesting Components VDC Power SupplyElevation Motor FaceplatePWM Motor Control SCR Motor ControlRelay Board Upper Display BoardCommon Symptoms Symptom Treadmill slows down when user steps onto treadbeltSymptom Treadmill speed is erratic and/or surges IR Potentiometer ADJUSTMENTS, PWM only = 9.3rpm = 8.0rpmRemoval and Replacement of Components Power Cord Line CordVDC Transformer Replacement Home Treadmills only Relay Board Sprint 4/PRG/SST Closed Loop onlyDrive Motor Brushes Unplug treadmillInstall new Elevation Motor Remove Elevation MotorTo Enter Diagnostic Mode To calibrate the potentiometerDeck REMOVAL/DECK Reversal UN Plug Treadmill Treadbelt Unplug TreadmillTake Up Roller/ Rear Roller Drive Roller/Front Roller Noises Page Visual Clues Drive MotorsElectronic Boards Elevation MotorVoltage Tests Diagnostic Guide Error CodesSeries Treadmill Configuration Mode Treadbelt TRACKING, Tensioning and Maintenance Treadbelt TrackingTreadbelt Tensioning Drive Belt Tensioning Unplug TreadmillYES Drive motor is good. Proceed to Step YES Button Code Prog Enter Pause Start Display Fast Slow DownYES Elevation Potentiometer Calibration Series Home Treadmill Symptom Symptom Any found? Is speed control wiring OK?Is it out of position? Any found?Is the motor wiring OK? UP Down Clockwise Sprint 8700 PRG 8700 SST Page BELT-RELAY Sprint Symptom Applies to Sprint 2 Only Treadmill is switched on? Applies to Sprint 2 Only See Sprint 2 Wiring Schematic for Speed POT Settings Elevation system will need to Tracking and Tensioning Check Drive Belt tension Recommended Maintenance Make Sure Treadmill is LevelDrive Roller Alignment ExampleWhen to lubricate How to lubricateService CHECK-LIST Institutional drive motor maintenanceIndex 5V LED Drive Motor Brushes LED Lights Safety Lanyard Uprights Frame