Landice 8700 manual Treadbelt, Upper Display Board Uprights, Upper Wire Harness, VFX System

Page 31

31

TREADBELT

This is the surface the user walks on. It rides over the deck and rollers.

UPPER DISPLAY BOARD

This controls information from the Membrane panel and Face Plate. It then transmits it to the relay board on Home models and the SCR on Club or LTD models.

UPRIGHTS

One on either side, they house the wire harness, the upper display, the cross member and the handrails.

UPPER WIRE HARNESS

Transmits data from lower electronics to upper electronics.

VFX SYSTEM

Shock-absorbing Deck. Consists of wood Deck, VFX Deck Post, Deck Spacer, Deck Load Washer, Deck Felt Washer, and Deck Impact Absorber.

Image 31

Contents Series Servicing Landice Treadmills InstallationIntroduction Parts IdentificationHow to Use this Manual Parts Landice Warranty and PoliciesTreadmill Parts Service LaborRecommended tools for servicing Landice treadmills Important Operating Safety Instructions Grounding Instructions 200 250 Volt Treadmills 15 Amp dedicated line Production Time Frame Settings Used In HomeStandard Membrane Sprint MembraneMembrane 8700 EP/PT MembraneSST Membrane 8700 PT2 MembraneSprint Faceplate Programmable MembraneParts Identification Em brane Panel-SPRINT3/4 70190 Side FR AM E XL Comercial Motor PAN Components Commercial Lower Wiring Schematic LED light emitting diode configurations SCR lower board Page Home SST VFX, PRG VFX, Sprint VFX Closed Loop Speed Sensor 8700 SST, PRG and Sprint VFX Treadmill LED Lights on PWM LED light emitting diode configurations Relay Board Sprint 3 treadmills have push button controls 8700 SST, PRG and Sprint 3, NON VFX TreadmillSprint Sprint 1 Lower Wiring Schematic Sprint 1&2 Upper Wiring Schematic Definitions Membrane Panel Safety LanyardSide Frame Covers IR PotentiometerVFX System Upper Wire HarnessTreadbelt Upper Display Board UprightsVDC Power Supply Testing ComponentsSCR Motor Control Elevation MotorFaceplate PWM Motor ControlUpper Display Board Relay BoardSymptom Treadmill slows down when user steps onto treadbelt Common SymptomsSymptom Treadmill speed is erratic and/or surges IR Potentiometer ADJUSTMENTS, PWM only = 8.0rpm = 9.3rpmPower Cord Line Cord Removal and Replacement of ComponentsRelay Board Sprint 4/PRG/SST Closed Loop only VDC Transformer Replacement Home Treadmills onlyUnplug treadmill Drive Motor BrushesRemove Elevation Motor Install new Elevation MotorTo calibrate the potentiometer To Enter Diagnostic ModeDeck REMOVAL/DECK Reversal UN Plug Treadmill Treadbelt Unplug TreadmillTake Up Roller/ Rear Roller Drive Roller/Front Roller Noises Page Elevation Motor Visual CluesDrive Motors Electronic BoardsVoltage Tests Error Codes Diagnostic GuideSeries Treadmill Configuration Mode Drive Belt Tensioning Unplug Treadmill Treadbelt TRACKING, Tensioning and MaintenanceTreadbelt Tracking Treadbelt TensioningYES Drive motor is good. Proceed to Step YES Prog Enter Pause Start Display Fast Slow Down Button CodeYES Elevation Potentiometer Calibration Series Home Treadmill Symptom Any found? SymptomAny found? Is speed control wiring OK? Is it out of position?Is the motor wiring OK? UP Down Clockwise Sprint 8700 PRG 8700 SST Page BELT-RELAY Sprint Symptom Applies to Sprint 2 Only Treadmill is switched on? Applies to Sprint 2 Only See Sprint 2 Wiring Schematic for Speed POT Settings Elevation system will need to Tracking and Tensioning Check Drive Belt tension Example Recommended MaintenanceMake Sure Treadmill is Level Drive Roller AlignmentHow to lubricate When to lubricateService CHECK-LIST Institutional drive motor maintenanceIndex 5V LED Drive Motor Brushes LED Lights Safety Lanyard Uprights Frame