Landice manual 8700 PT2 Membrane, SST Membrane

Page 12

12

8700 PT2 Membrane

Models That Used This Membrane: 8700-PT2,8700-CLUB-PT2

Production Time Frame: 1994-1998

Electronics: Standard 110V SCR (220V SCR for CLUB units), commercial motor pan.

See Wiring Diagram.

Settings Used In: Home and Commercial

Key Features: Closed Loop Treadmill (w/ Speed sensor) Safety Lanyard, 0.5-11.0MPH Push Button Speed and Elevation Control, 9 Built In Programs, 4 User Programs, Wireless Heart Rate Control, SONAR ranging capability (Optional), LED Graphic Display.

8700 SST Membrane

Models That Used This Membrane: 8700-SST,8700-SST-VFX

Production Time Frame: 1995-1999

Electronics: 8700-SST used Sprint-3 electronics, 8700-SST-VFX used Sprint-4 electronics,

See Wiring Diagrams.

Settings Used In: Home

Key Features: 8700-SST Open Loop Treadmill (w/o speed sensor), 8700-SST-VFX Closed Loop Treadmill (w/ Speed sensor) Safety Lanyard, 0.5-12.0MPH Push Button Speed and Elevation Control. 5 Built In Programs, 5 User Programs, Wireless Heart Rate Control, SONAR ranging capability.

Image 12

Contents Series Installation IntroductionParts Identification Servicing Landice TreadmillsHow to Use this Manual Landice Warranty and Policies PartsService Labor Treadmill PartsRecommended tools for servicing Landice treadmills Important Operating Safety Instructions Grounding Instructions 200 250 Volt Treadmills 15 Amp dedicated line Settings Used In Home Standard MembraneSprint Membrane Production Time Frame8700 EP/PT Membrane Membrane8700 PT2 Membrane SST MembraneProgrammable Membrane Sprint FaceplateParts Identification Em brane Panel-SPRINT3/4 70190 Side FR AM E XL Comercial Motor PAN Components Commercial Lower Wiring Schematic LED light emitting diode configurations SCR lower board Page Home SST VFX, PRG VFX, Sprint VFX Closed Loop Speed Sensor 8700 SST, PRG and Sprint VFX Treadmill LED Lights on PWM LED light emitting diode configurations Relay Board 8700 SST, PRG and Sprint 3, NON VFX Treadmill Sprint 3 treadmills have push button controlsSprint Sprint 1 Lower Wiring Schematic Sprint 1&2 Upper Wiring Schematic Definitions Safety Lanyard Side Frame CoversIR Potentiometer Membrane PanelUpper Wire Harness TreadbeltUpper Display Board Uprights VFX SystemTesting Components VDC Power SupplyElevation Motor FaceplatePWM Motor Control SCR Motor ControlRelay Board Upper Display BoardCommon Symptoms Symptom Treadmill slows down when user steps onto treadbeltSymptom Treadmill speed is erratic and/or surges IR Potentiometer ADJUSTMENTS, PWM only = 9.3rpm = 8.0rpmRemoval and Replacement of Components Power Cord Line CordVDC Transformer Replacement Home Treadmills only Relay Board Sprint 4/PRG/SST Closed Loop onlyDrive Motor Brushes Unplug treadmillInstall new Elevation Motor Remove Elevation MotorTo Enter Diagnostic Mode To calibrate the potentiometerTreadbelt Unplug Treadmill Deck REMOVAL/DECK Reversal UN Plug TreadmillTake Up Roller/ Rear Roller Drive Roller/Front Roller Noises Page Visual Clues Drive MotorsElectronic Boards Elevation MotorVoltage Tests Diagnostic Guide Error CodesSeries Treadmill Configuration Mode Treadbelt TRACKING, Tensioning and Maintenance Treadbelt TrackingTreadbelt Tensioning Drive Belt Tensioning Unplug TreadmillYES Drive motor is good. Proceed to Step YES Button Code Prog Enter Pause Start Display Fast Slow DownYES Elevation Potentiometer Calibration Series Home Treadmill Symptom Symptom Any found? Is speed control wiring OK?Is it out of position? Any found?Is the motor wiring OK? UP Down Clockwise Sprint 8700 PRG 8700 SST Page BELT-RELAY Sprint Symptom Applies to Sprint 2 Only Treadmill is switched on? Applies to Sprint 2 Only See Sprint 2 Wiring Schematic for Speed POT Settings Elevation system will need to Tracking and Tensioning Check Drive Belt tension Recommended Maintenance Make Sure Treadmill is LevelDrive Roller Alignment ExampleWhen to lubricate How to lubricateInstitutional drive motor maintenance Service CHECK-LISTIndex 5V LED Drive Motor Brushes LED Lights Safety Lanyard Uprights Frame