Landice manual 8700 EP/PT Membrane

Page 11

11

8700 EP/PT Membrane

Models That Used This Membrane: 8700EP, 8700-PT

Production Time Frame: 1991-1993

Electronics: Standard 110V SCR (220V SCR for CLUB units), commercial motor pan.

See Wiring Diagram.

Settings Used In: Home and Commercial

Key Features: Closed Loop Treadmill (w/ Speed sensor) Safety Lanyard, 0.5-11.0MPH Push Button Speed and Elevation Control, 10 Built In Programs, 4 User Programs, Wireless Heart Rate Control (Optional), LED Graphic Display.

8700 P Membrane

Models That Used This Membrane: 8700-P,8700-LTD-P,8700-CLUB-P

Production Time Frame: 1991-1999

Electronics: Standard 110V SCR (220V SCR for CLUB units), commercial motor pan.

See Wiring Diagram.

Settings Used In: Home and Commercial (LTD’s and CLUB’s)

Key Features: Closed Loop Treadmill (w/ speed sensor), Safety Lanyard, 0.5-11MPH Push Button

Speed and Elevation Control, 5 Built In Programs.

Image 11

Contents Series Servicing Landice Treadmills InstallationIntroduction Parts IdentificationHow to Use this Manual Parts Landice Warranty and PoliciesTreadmill Parts Service LaborRecommended tools for servicing Landice treadmills Important Operating Safety Instructions Grounding Instructions 200 250 Volt Treadmills 15 Amp dedicated line Production Time Frame Settings Used In HomeStandard Membrane Sprint MembraneMembrane 8700 EP/PT MembraneSST Membrane 8700 PT2 MembraneSprint Faceplate Programmable MembraneParts Identification Em brane Panel-SPRINT3/4 70190 Side FR AM E XL Comercial Motor PAN Components Commercial Lower Wiring Schematic LED light emitting diode configurations SCR lower board Page Home SST VFX, PRG VFX, Sprint VFX Closed Loop Speed Sensor 8700 SST, PRG and Sprint VFX Treadmill LED Lights on PWM LED light emitting diode configurations Relay Board Sprint 3 treadmills have push button controls 8700 SST, PRG and Sprint 3, NON VFX TreadmillSprint Sprint 1 Lower Wiring Schematic Sprint 1&2 Upper Wiring Schematic Definitions Membrane Panel Safety LanyardSide Frame Covers IR PotentiometerVFX System Upper Wire HarnessTreadbelt Upper Display Board UprightsVDC Power Supply Testing ComponentsSCR Motor Control Elevation MotorFaceplate PWM Motor ControlUpper Display Board Relay BoardSymptom Treadmill slows down when user steps onto treadbelt Common SymptomsSymptom Treadmill speed is erratic and/or surges IR Potentiometer ADJUSTMENTS, PWM only = 8.0rpm = 9.3rpmPower Cord Line Cord Removal and Replacement of ComponentsRelay Board Sprint 4/PRG/SST Closed Loop only VDC Transformer Replacement Home Treadmills onlyUnplug treadmill Drive Motor BrushesRemove Elevation Motor Install new Elevation MotorTo calibrate the potentiometer To Enter Diagnostic ModeTake Up Roller/ Rear Roller Treadbelt Unplug TreadmillDeck REMOVAL/DECK Reversal UN Plug Treadmill Drive Roller/Front Roller Noises Page Elevation Motor Visual CluesDrive Motors Electronic BoardsVoltage Tests Error Codes Diagnostic GuideSeries Treadmill Configuration Mode Drive Belt Tensioning Unplug Treadmill Treadbelt TRACKING, Tensioning and MaintenanceTreadbelt Tracking Treadbelt TensioningYES Drive motor is good. Proceed to Step YES Prog Enter Pause Start Display Fast Slow Down Button CodeYES Elevation Potentiometer Calibration Series Home Treadmill Symptom Any found? SymptomAny found? Is speed control wiring OK? Is it out of position?Is the motor wiring OK? UP Down Clockwise Sprint 8700 PRG 8700 SST Page BELT-RELAY Sprint Symptom Applies to Sprint 2 Only Treadmill is switched on? Applies to Sprint 2 Only See Sprint 2 Wiring Schematic for Speed POT Settings Elevation system will need to Tracking and Tensioning Check Drive Belt tension Example Recommended MaintenanceMake Sure Treadmill is Level Drive Roller AlignmentHow to lubricate When to lubricateIndex Institutional drive motor maintenanceService CHECK-LIST 5V LED Drive Motor Brushes LED Lights Safety Lanyard Uprights Frame