Landice 8700 manual Grounding Instructions

Page 8

8

DANGER

To reduce the risk of electric shock, always unplug the treadmill from the electrical outlet immediately after using. Always unplug the treadmill before cleaning or removing the motor cover.

WARNING

To reduce the risk of burns, fire, electric shock, or injury to persons:

1Treadmill should never be left unattended when plugged in. Unplug from outlet when not in use.

2Close supervision is necessary when this unit is used by or near children or disabled persons.

3Use this treadmill only for its intended use as described in this manual.

4Do not operate this treadmill if it has a damaged cord or plug, if it is not working properly or if it has been damaged. Call your selling dealer immediately for examination and repair.

5Keep the power cord away from heated surfaces. Be sure the line cord has plenty of slack and does not get pinched underneath the treadmill when it elevates and lowers. If an extension cord must be used do not use one longer than 6 feet with 12 gauge wire.

6Never operate the treadmill with the air openings blocked. Keep the air openings free of lint, hair, and the like.

7Never drop or insert any object into any opening. Be sure no objects are near or underneath the moving treadbelt when using the treadmill.

8Do not use outdoors.

9Do not operate where aerosol spray products are being used or where oxygen is being administered.

10Connect this appliance to a properly grounded outlet only. Do not use a GFI outlet.

11To disconnect, press the OFF button, remove the SAFETY LANYARD, and unplug the unit from the wall outlet.

GROUNDING INSTRUCTIONS

This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances. We do not recommend using a GFI outlet.

120 Volt Treadmills (15 Amp dedicated line)

Treadmills marked 120 VAC are intended for use in a nominal 120-volt circuit with a grounding plug. Make sure the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product.

Image 8
Contents Series Installation IntroductionParts Identification Servicing Landice TreadmillsHow to Use this Manual Landice Warranty and Policies PartsService Labor Treadmill PartsRecommended tools for servicing Landice treadmills Important Operating Safety Instructions Grounding Instructions 200 250 Volt Treadmills 15 Amp dedicated line Settings Used In Home Standard MembraneSprint Membrane Production Time Frame8700 EP/PT Membrane Membrane8700 PT2 Membrane SST MembraneProgrammable Membrane Sprint FaceplateParts Identification Em brane Panel-SPRINT3/4 70190 Side FR AM E XL Comercial Motor PAN Components Commercial Lower Wiring Schematic LED light emitting diode configurations SCR lower board Page Home SST VFX, PRG VFX, Sprint VFX Closed Loop Speed Sensor 8700 SST, PRG and Sprint VFX Treadmill LED Lights on PWM LED light emitting diode configurations Relay Board 8700 SST, PRG and Sprint 3, NON VFX Treadmill Sprint 3 treadmills have push button controlsSprint Sprint 1 Lower Wiring Schematic Sprint 1&2 Upper Wiring Schematic Definitions Safety Lanyard Side Frame CoversIR Potentiometer Membrane PanelUpper Wire Harness TreadbeltUpper Display Board Uprights VFX SystemTesting Components VDC Power SupplyElevation Motor FaceplatePWM Motor Control SCR Motor ControlRelay Board Upper Display BoardCommon Symptoms Symptom Treadmill slows down when user steps onto treadbeltSymptom Treadmill speed is erratic and/or surges IR Potentiometer ADJUSTMENTS, PWM only = 9.3rpm = 8.0rpmRemoval and Replacement of Components Power Cord Line CordVDC Transformer Replacement Home Treadmills only Relay Board Sprint 4/PRG/SST Closed Loop onlyDrive Motor Brushes Unplug treadmillInstall new Elevation Motor Remove Elevation MotorTo Enter Diagnostic Mode To calibrate the potentiometerTake Up Roller/ Rear Roller Treadbelt Unplug TreadmillDeck REMOVAL/DECK Reversal UN Plug Treadmill Drive Roller/Front Roller Noises Page Visual Clues Drive MotorsElectronic Boards Elevation MotorVoltage Tests Diagnostic Guide Error CodesSeries Treadmill Configuration Mode Treadbelt TRACKING, Tensioning and Maintenance Treadbelt TrackingTreadbelt Tensioning Drive Belt Tensioning Unplug TreadmillYES Drive motor is good. Proceed to Step YES Button Code Prog Enter Pause Start Display Fast Slow DownYES Elevation Potentiometer Calibration Series Home Treadmill Symptom Symptom Any found? Is speed control wiring OK?Is it out of position? Any found?Is the motor wiring OK? UP Down Clockwise Sprint 8700 PRG 8700 SST Page BELT-RELAY Sprint Symptom Applies to Sprint 2 Only Treadmill is switched on? Applies to Sprint 2 Only See Sprint 2 Wiring Schematic for Speed POT Settings Elevation system will need to Tracking and Tensioning Check Drive Belt tension Recommended Maintenance Make Sure Treadmill is LevelDrive Roller Alignment ExampleWhen to lubricate How to lubricateIndex Institutional drive motor maintenanceService CHECK-LIST 5V LED Drive Motor Brushes LED Lights Safety Lanyard Uprights Frame