Landice 8700 manual Drive Roller/Front Roller

Page 45

45

Drive Roller/Front Roller

1.Release all treadbelt tension. 9/16" bolts on rear roller.

2.Remove drive belt from drive motor. Release tension on drive motor tensioning hook (7/16" nut located underside of motor pan). Pivot motor towards treadbelt and slide drive-belt off.

3.Remove (2) Philips Head or (2) Hex Head screws securing drive roller to treadmill frame.

4.Remove roller.

5.REVERSE STEPS FOR INSTALL /FOLLOW TENSIONING PROCEDURES

Image 45

Contents Series Introduction InstallationParts Identification Servicing Landice TreadmillsHow to Use this Manual Parts Landice Warranty and PoliciesTreadmill Parts Service LaborRecommended tools for servicing Landice treadmills Important Operating Safety Instructions Grounding Instructions 200 250 Volt Treadmills 15 Amp dedicated line Standard Membrane Settings Used In HomeSprint Membrane Production Time FrameMembrane 8700 EP/PT MembraneSST Membrane 8700 PT2 MembraneSprint Faceplate Programmable MembraneParts Identification Em brane Panel-SPRINT3/4 70190 Side FR AM E XL Comercial Motor PAN Components Commercial Lower Wiring Schematic LED light emitting diode configurations SCR lower board Page Home SST VFX, PRG VFX, Sprint VFX Closed Loop Speed Sensor 8700 SST, PRG and Sprint VFX Treadmill LED Lights on PWM LED light emitting diode configurations Relay Board Sprint 3 treadmills have push button controls 8700 SST, PRG and Sprint 3, NON VFX TreadmillSprint Sprint 1 Lower Wiring Schematic Sprint 1&2 Upper Wiring Schematic Definitions Side Frame Covers Safety LanyardIR Potentiometer Membrane PanelTreadbelt Upper Wire HarnessUpper Display Board Uprights VFX SystemVDC Power Supply Testing ComponentsFaceplate Elevation MotorPWM Motor Control SCR Motor ControlUpper Display Board Relay BoardSymptom Treadmill slows down when user steps onto treadbelt Common SymptomsSymptom Treadmill speed is erratic and/or surges IR Potentiometer ADJUSTMENTS, PWM only = 8.0rpm = 9.3rpmPower Cord Line Cord Removal and Replacement of ComponentsRelay Board Sprint 4/PRG/SST Closed Loop only VDC Transformer Replacement Home Treadmills onlyUnplug treadmill Drive Motor BrushesRemove Elevation Motor Install new Elevation MotorTo calibrate the potentiometer To Enter Diagnostic ModeTreadbelt Unplug Treadmill Deck REMOVAL/DECK Reversal UN Plug TreadmillTake Up Roller/ Rear Roller Drive Roller/Front Roller Noises Page Drive Motors Visual CluesElectronic Boards Elevation MotorVoltage Tests Error Codes Diagnostic GuideSeries Treadmill Configuration Mode Treadbelt Tracking Treadbelt TRACKING, Tensioning and MaintenanceTreadbelt Tensioning Drive Belt Tensioning Unplug TreadmillYES Drive motor is good. Proceed to Step YES Prog Enter Pause Start Display Fast Slow Down Button CodeYES Elevation Potentiometer Calibration Series Home Treadmill Symptom Any found? Is speed control wiring OK? SymptomIs it out of position? Any found?Is the motor wiring OK? UP Down Clockwise Sprint 8700 PRG 8700 SST Page BELT-RELAY Sprint Symptom Applies to Sprint 2 Only Treadmill is switched on? Applies to Sprint 2 Only See Sprint 2 Wiring Schematic for Speed POT Settings Elevation system will need to Tracking and Tensioning Check Drive Belt tension Make Sure Treadmill is Level Recommended MaintenanceDrive Roller Alignment ExampleHow to lubricate When to lubricateInstitutional drive motor maintenance Service CHECK-LISTIndex 5V LED Drive Motor Brushes LED Lights Safety Lanyard Uprights Frame