Healthrider HRTL20510.1 manual HOW to USE the Maintenance Mode

Page 29

HOW TO USE THE MAINTENANCE MODE

The console features a maintenance mode that allows you to calibrate the incline and speed of the treadmill, update the console firmware, calibrate the screen, view technical information, and perform a network test.

1.Select the settings mode. See step 1 on page 27.

2.Select the maintenance mode.

Touch the Maintenance button in the lower right corner of the screen to

enter the maintenance mode.

The maintenance mode main screen will show

information about the model and version of the treadmill. If the console is connected to the con- troller of the treadmill, the controller dot will be green; if it is not, the dot will flash. If the treadmill is connected to your wireless network, the network dot will be green; if it is not, the dot will be black.

3.Calibrate the incline system of the treadmill. Touch the Calibrate Incline button. Then, touch the Begin button to calibrate the incline system. The treadmill will automatically rise to the maximum in- cline level, lower to the minimum incline level, and

then return to the starting position. This will cali- brate the incline system. Press the Cancel button to return to the maintenance mode. When the in- cline system is calibrated, touch the Finish button.

IMPORTANT: Keep pets, feet, and other objects away from the treadmill while the incline system is calibrating. In an emergency, pull the key from the console to stop the incline calibration.

4.Calibrate the speed of the treadmill. Calibrate the speed of the treadmill only if in- structed to do so by an authorized service repre- sentative.

Note: The Calibrate Speed button may not be en- abled on your treadmill.

5.Update the console firmware.

For the best results, regularly check for firmware updates.

Touch the Firmware Update button. Next, touch the WiFi button to check for firmware updates using your wireless network. Then, touch the Begin button to check for updates or the Cancel button to return to the maintenance mode.

To avoid damaging the treadmill, do not turn off the power or remove the key while the firmware is being updated.

29

Image 29
Contents Model No. HRTL20510.1 Serial No QUESTIONS?Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Important Precautions Instructions Save TheseBefore YOU Begin Part Identification Chart Assembly requires two persons AssemblyIng materials until you finish assembly Packing materials. Do not dispose of the packAttach the Right Upright not shown See the inset drawing. Tie the wire tieUpright 88 do not fully tighten the Patch Page Tie s Bracket Pulse Wire Page Side is shown do not tighten the Patch Screws yet Raise the Frame 57 to the position shown Page HOW to PUT on the Chest Pulse Sensor HOW to USE the Chest Pulse SensorCare and Maintenance TroubleshootingPRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console Console DiagramHOW to SET UP the Console HOW to Turn on the PowerInsert the key into the console HOW to USE the Manual ModeBegin working out Page Turn on the fan if desired COOL-DOWN ModeMeasure your heart rate if desired Start the workout HOW to USE AN Onboard WorkoutHOW to USE AN Ifit Live Workout Ifit Live FCC Information HOW to USE the Internet Browser Select the wireless network mode HOW to USE the Settings ModeLog in to your iFit Live account Exit the settings modeSelect a language Select the unit of measurementSelect the settings mode. See on Select the maintenance mode HOW to USE the Maintenance ModeView technical information HOW to USE the Stereo Sound System HOW to Fold the Treadmill HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USESymptom The power turns off during use TroubleshootingSymptom The walking belt slows when walked on Symptom The iFit Live mode does not function correctlyPage Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Key No. Qty Description Part ListQty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty