Healthrider HRTL20510.1 manual Symptom The iFit Live mode does not function correctly

Page 34

Locate the Reed Switch (55) and the Magnet (54) on the left side of the Pulley (53). Turn the Pulley until the Magnet is aligned with the Reed Switch.

Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the #8 x 3/4" Tek Screw (80), move the Reed Switch slightly, and then retighten the Screw. Reattach the Motor Hood (not shown) and run the treadmill for a few minutes to check for a correct speed reading.

80	53
55	54
1/8 in.

Top

View

SYMPTOM: The incline of the treadmill does not change correctly

a.Recalibrate the incline system (see step 3 on page 29).

SYMPTOM: The iFit Live mode does not function correctly

a.If the iFit Live mode is not functioning correctly, make sure that the treadmill has the most current firmware available (see step 6 on page 29).

SYMPTOM: The walking belt slows when walked on

a.Use only a single-outlet surge suppressor that meets all of the specifications described on page 17.

b.If the walking belt is overtightened, treadmill perfor- mance may decrease and the walking belt may be- come damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller screws counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walk- ing belt is properly tightened.

b

2–3 in.

Idler Roller Screws

c.If the walking belt still slows when walked on, see the front cover of this manual.

34

Image 34

Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. HRTL20510.1 Serial No On the WEBTable of Contents Important Precautions Save These InstructionsBefore YOU Begin Part Identification Chart Ing materials until you finish assembly AssemblyAssembly requires two persons Packing materials. Do not dispose of the packUpright 88 do not fully tighten the Patch See the inset drawing. Tie the wire tieAttach the Right Upright not shown Page Tie s Bracket Pulse Wire Page Side is shown do not tighten the Patch Screws yet Raise the Frame 57 to the position shown Page Care and Maintenance HOW to USE the Chest Pulse SensorHOW to PUT on the Chest Pulse Sensor TroubleshootingHOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to SET UP the ConsoleBegin working out HOW to USE the Manual ModeInsert the key into the console Page Measure your heart rate if desired COOL-DOWN ModeTurn on the fan if desired HOW to USE AN Onboard Workout Start the workoutHOW to USE AN Ifit Live Workout Ifit Live FCC Information HOW to USE the Internet Browser HOW to USE the Settings Mode Select the wireless network modeSelect a language Exit the settings modeLog in to your iFit Live account Select the unit of measurementHOW to USE the Maintenance Mode Select the settings mode. See on Select the maintenance modeView technical information HOW to USE the Stereo Sound System HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill HOW to Lower the Treadmill for USETroubleshooting Symptom The power turns off during useSymptom The iFit Live mode does not function correctly Symptom The walking belt slows when walked onPage Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Part List Key No. Qty DescriptionQty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT