VDO Cyclecomputing Z3 PC-LINK manual Handlebar holder, Speed transmitter and magnet P07

Page 21

EN

2, and the altitude difference walked. Reprogram this information after inserting the new batteries.

2.1.2 BATTERY INSTALLATION PULSE-CHEST BELT >>> P03

Your VDO is shipped with the battery installed in the pulse-chest belt. Proceed as follows when later inserting a replacement battery:

step 1 Insert the battery into the chest-belt housing with the +pole up. step 2 Ensure that the battery is not tilted.

step 3 Strictly ensure that the rubber seal lies smoothly on the battery compartment lid.

step 4 Insert the battery compartment lid into the opening and use a coin to firmly turn the battery door to right until the stop (approximately 1/3 turn)

2.2. INSTALLATION - HOLDER/COMPUTER/TRANSMITTER/MAGNET

a. Holder >>> P04 / 05: Your VDO computer is shipped with a universal handlebar holder.

step 1 You can mount the holder either on the handlebar or the stem. If you are installing the holder on the handlebar decide whether you want it on the right side or the left side. If installing on the stem, loosen the screws in the holder and turn the foot of the holder to stem installation. Then screw the foot firmly onto the holder again.

step 2 Route the cable ties through the provided eyes of the holder foot and pull both of them tight.

b. Computer >>> P06

The VDO twist-click system securely connects the computer to the

handlebar holder.

step 1 Insert the computer, turned to the left approximately 45 degrees (10 o‘clock position) into the holder.

step 2 Twist the computer to the right until it audibly engages (clicks) in the holder system (12 o‘clock position).

step 3 To remove the computer turn it to the left (do not press or pull).

c. Speed transmitter and magnet >>> P07

Mount the transmitter on the same side of the handlebar that the com- puter is mounted on. If you have installed the holder on the stem then we recommend mounting the transmitter on the left side.

step 1 Loosely fasten the transmitter on the fork with cable ties (do not tighten).

step 2 Place the spoke magnet on a spoke

step 3 Align the spoke magnet to the transmitter marking with a clearance of approximately 3 mm and click it together.

step 4 Align transmitter and magnet relative to each other and tighten the cable tie on the transmitter.

Please pay attention to the maximum distances:

-Maximum transmitter-computer distance = 120 cm

-Transmitter-magnet distance: 3 mm to a maximum of 10 mm

2.3. PUTTING ON THE PULSE-CHEST BELT >>> P08

step 1 First connect the one side of the pulse transmitter with the elastic strap, as shown. Press the ends of the pulse-chest belt into the plastic holder of the elastic strap

step 2 Place the pulse transmitter just below your chest and guide

12

Image 21
Contents VDO Series Z My Settings Picturebook P02 P03 P04/05 P06 P07 P08 P09 WS in mm / inch P11 Congratulations Cable ties Optional extension set VDO cadence transmitterP01 P01 page 1 in the picture book Initial operation, AC-button Language selection Personal settings with manual max. pulse entryLap timer Stopwatch Selecting the operation mode Bike mode or walk modeGetting Started Permanent functions in the displayControl System Operation Guarantee Conditions Technical Specifications GeneralFunctions Press button ç for 3 seconds To go to setting modeMiddle BAR DisplayDesignation Extension Options & AccessoriesSpeed transmitter and magnet P07 Handlebar holderPutting on the PULSE-CHEST Belt P08 Place the pulse transmitter just below your chest and guideInitial OPERATION, AC-BUTTON P09-2 Range of the pulse-chest belt transmitter = 0.90 mLanguage Selection Age appearsSpeed Pairing Pulse PairingCadence Pairing Initial Operation Pulse TransmitterSetting Time & Date Setting the LanguageSetting the ALARM, Alarm Clock Alarm SET… SET Size ?CONTINUE? Wheelsize SET?SET OK? SET DoneBike Check / Service Interval Setting Total KilometersOdometer SET ‚ ODO Bike 1/2 Next DIGIT?Person Data SET SET Weight ?CONTINUE?SET AGE ?CONTINUE? SET SEX ?CONTINUE?Pulse Limit ?SET? Pulse Limit Settings‚ Auto Limit 1 HIGH…LOW Manual Entry of Pulse Limit ValuesRecovery SET SET Recovery Pulse MeasurementMeasuring the Recovery PULSE/RECOVERY Time Select Training Program‚ Power Calc SET Done Power Calc SETBike Type Select „SITTING POS SelectAnnual Uphill Altitude Gain Bike 1 and Bike 2 and Walk Mode Setting the Actual AltitudeHome Alti SET Home Alti ?SET OK?Trip Data Reset Done Trip Data ?RESET?Reset Total Ride Time ‚ Total Time Reset DONE?‚ Odototal Reset Done Resetting the Total Distance MeterResetting the Navigator ‚ Navigator Reset DonePermanent Functions Trip Data Reset Done LHeader Center BARTrip MAX „TRIP Data ?RESET?„AVG Climb MAX ClimbMAX Down ‚ Trip Data Reset DoneTrip Distance Ride TimeOption only with Cadence Extension MAX SpeedCadence CAD AVGOdototal ODO BikeTime Bike StopwatchAVG Pulse LAP RECMAX Pulse Pulse MAX %Calorie Selecting Navigator ModeNavigator SET BackwardNavigator Reset Done Navigator ?RESET?‚ „NAVIGATOR Next Digit ‚ Navigator ?SET OK?Timer ?SELECT? Timer SettingsLAP Timer ?SELECT? Timer ?SET?LAP-TIMER ‚ Timer 1+2 SET DoneCountdown ?SET? ‚ SET Minutes ?CONTINUE?Training with Timer 1 / Timer 2 / Timer 1+2 Training with the Stopwatch13.2 Beginning of the recording Start the recording 4sec Combination timer 1+2 Training with the Countdown TimerBeginning of the recording Start the recording 4sec Lap time Average pulse during the lap Training with the LAP TimerLap number and time of the lap Training PrerequisiteBar Manual delete of training data is not possibleTransferring Data to Your PC P11 PC Link SelectSelection of the Recording Interval For Wake UP Check the batteryDescription special case On the transmitterSpeed signal Chest belt Belt Check the batteryReceiving cadence signals No speed displayIs in the set training ranges Start timer Personal maximum pulse Timer has not been startedInstalled Service yourselfCycle Parts GmbH, Große Ahlmühle 33, D-76865 Rohrbach Guarantee ConditionsTechnical Specifications .-641/W.. Page Смесва с други отпадъци на работното място FIN  !$!! 7f6524j6.-64%0+.-6410+%0 Page SLO EU-Konformitätserklärung EU-Declaration of Conformity USA CDN USA CDN VDO Series Z

Z3 PC-LINK specifications

The VDO Cyclecomputing Z3 PC-LINK is a cutting-edge bicycle computer that combines high-performance functionality with user-friendly features, making it an essential tool for both casual cyclists and serious athletes. One of its standout features is the robust wireless connectivity that allows seamless data transfer to a personal computer for detailed analysis. This capability enables cyclists to track their performance over time, monitor progress, and adjust their training accordingly.

Equipped with a large, easy-to-read display, the Z3 PC-LINK provides real-time data, including current speed, average speed, distance traveled, and ride time. Additionally, it tracks features such as maximum speed, total distance, and elapsed time. Its intuitive interface makes it incredibly user-friendly, allowing cyclists to quickly navigate through various data points while on the move.

The Z3 PC-LINK is designed for versatility, catering to various cycling disciplines, from road biking to mountain biking. It can function as a basic speedometer for casual riders or a sophisticated tool for seasoned athletes. The device supports multiple bike profiles, enabling users to easily switch between bikes without having to reconfigure settings.

One of the key technologies integrated into the Z3 PC-LINK is the GPS functionality, which provides accurate tracking of routes taken. This feature allows users to map their rides, making it easier to explore new trails and roads while keeping track of performance metrics.

Additionally, the Z3 PC-LINK is built with durability in mind, featuring a weather-resistant casing that withstands the rigors of outdoor cycling. Its long battery life ensures that it can keep up with extended rides and adventures, making it a reliable companion for any cycling journey.

Another noteworthy characteristic is the compatibility with various sensors and devices, including heart rate monitors and cadence sensors. By integrating these additional data sources, cyclists can gain deeper insights into their performance, facilitating a more comprehensive understanding of their physical condition and cycling efficiency.

In conclusion, the VDO Cyclecomputing Z3 PC-LINK stands out in the crowded market of bicycle computers. With its advanced features, user-friendly design, and reliable performance, it empowers cyclists to take control of their training and routes effectively. Whether for leisure or competitive cycling, the Z3 PC-LINK is an invaluable asset for enhancing the cycling experience.