VDO Cyclecomputing Z3 PC-LINK Permanent Functions, Header, Center BAR, Footer, Alti UP, Dist UP

Page 34

INSTRUCTION MANUAL

11. OPERATION MODE

11.1.An overview of mode functions is provided in section 1.3.1.

11.2FAST PAIRING after transmission interruption

If no signal is received from one of your already paired transmitters for more than 15 minutes (e.g. cycling without pulse-chest belt, magnet moved unintentionally) the receive channel for this transmitter will be closed. In this case your VDO computer will show dashes for the respective function in the display. To re-open all receive channels press

the ç and ¥ buttons at the same time:

In this case your VDO computer will then receive all paired transmitters that are in range. See also chapter 15 Sleep mode

11.3.GETTING STARTED - quick overview Functions/operation/reset/max values

11.3.0. PERMANENT FUNCTIONS

The following functions are permanently shown in the display:

HEADER

-Actual altitude

-Actual temperature

-Actual ascending gradient in percent ! Not in walk mode !

CENTER BAR

-Heart rate receive icon if the pulse transmitter belt is worn

-Beeper icon if the beeper is switched on

-Stopwatch icon if the timing function is running

-Actual heart rate

This resets all data of the functions marked by L.

-Actual speed: Maximum value 120 km/h or mph (! not in walk mode !)

-Comparison of actual speed to average speed= above,=below (! not in walk mode !)

-Selected wheel size 1 or 2

-REC for ongoing recording

FOOTER

- Shows selected information and corresponding value

ALTITUDE FUNCTIONS (button ¥ )

Re-calibrating the air pressure to home altitude. Short-cut press the ¥ button for 4 seconds.

11.3.1. ¬ £	ALTI UP = uphill altitude gain for the actual trip
Display	¥	ALTI UP
Reset: 3 sec.	√	TRIP DATA ?RESET?
	‚	TRIP DATA ?RESET? <<?RESET?>> ﬂashing
	‚	TRIP DATA RESET DONE L

Automatic return to operation mode for TRIP DIST

11.3.2. ¬ DIST UP = uphill distance of the actual trip

Display	¥	DIST UP
Reset: 3 sec.	√	TRIP DATA ?RESET?
	‚	TRIP DATA ?RESET? <<?RESET?>> ﬂashing
	‚	TRIP DATA RESET DONE

This resets all data of the functions marked by L

Automatic return to operation mode for TRIP DIST

25

Image 34

Contents VDO Series Z My Settings Picturebook P02 P03 P04/05 P06 P07 P08 P09 WS in mm / inch P11 Cable ties Optional extension set VDO cadence transmitter CongratulationsP01 P01 page 1 in the picture book Personal settings with manual max. pulse entry Initial operation, AC-button Language selectionGetting Started Selecting the operation mode Bike mode or walk modeLap timer Stopwatch Permanent functions in the displayGuarantee Conditions Technical Specifications General Control System OperationFunctions To go to setting mode Press button ç for 3 secondsDisplay Middle BARExtension Options & Accessories DesignationPutting on the PULSE-CHEST Belt P08 Handlebar holderSpeed transmitter and magnet P07 Place the pulse transmitter just below your chest and guideLanguage Selection Range of the pulse-chest belt transmitter = 0.90 mInitial OPERATION, AC-BUTTON P09-2 Age appearsCadence Pairing Pulse PairingSpeed Pairing Initial Operation Pulse TransmitterSetting the ALARM, Alarm Clock Setting the LanguageSetting Time & Date Alarm SET?SET OK? Wheelsize SET… SET Size ?CONTINUE? SET DoneOdometer SET Setting Total KilometersBike Check / Service Interval ‚ ODO Bike 1/2 Next DIGIT?SET AGE ?CONTINUE? SET Weight ?CONTINUE?Person Data SET SET SEX ?CONTINUE?‚ Auto Limit 1 HIGH…LOW Pulse Limit SettingsPulse Limit ?SET? Manual Entry of Pulse Limit ValuesMeasuring the Recovery PULSE/RECOVERY Time SET Recovery Pulse MeasurementRecovery SET Select Training ProgramBike Type Select Power Calc SET‚ Power Calc SET Done „SITTING POS Select Home Alti SET Setting the Actual Altitude Annual Uphill Altitude Gain Bike 1 and Bike 2 and Walk Mode Home Alti ?SET OK?Reset Total Ride Time Trip Data ?RESET?Trip Data Reset Done ‚ Total Time Reset DONE?Resetting the Navigator Resetting the Total Distance Meter‚ Odototal Reset Done ‚ Navigator Reset DoneHeader Trip Data Reset Done LPermanent Functions Center BAR„AVG Climb „TRIP Data ?RESET?Trip MAX MAX ClimbTrip Distance ‚ Trip Data Reset DoneMAX Down Ride TimeCadence MAX SpeedOption only with Cadence Extension CAD AVGTime Bike ODO BikeOdototal StopwatchMAX Pulse LAP RECAVG Pulse Pulse MAX %Navigator SET Selecting Navigator ModeCalorie Backward‚ „NAVIGATOR Next Digit Navigator ?RESET?Navigator Reset Done ‚ Navigator ?SET OK?LAP Timer ?SELECT? Timer SettingsTimer ?SELECT? Timer ?SET?Countdown ?SET? ‚ Timer 1+2 SET DoneLAP-TIMER ‚ SET Minutes ?CONTINUE?Training with the Stopwatch Training with Timer 1 / Timer 2 / Timer 1+213.2 Beginning of the recording Start the recording 4sec Training with the Countdown Timer Combination timer 1+2Beginning of the recording Start the recording 4sec Training with the LAP Timer Lap time Average pulse during the lapTraining Prerequisite Lap number and time of the lapManual delete of training data is not possible BarPC Link Select Transferring Data to Your PC P11Selection of the Recording Interval Description special case Check the batteryFor Wake UP On the transmitterReceiving cadence signals Chest belt Belt Check the batterySpeed signal No speed displayInstalled Personal maximum pulse Timer has not been startedIs in the set training ranges Start timer Service yourselfGuarantee Conditions Cycle Parts GmbH, Große Ahlmühle 33, D-76865 RohrbachTechnical Specifications .-641/W.. Page Смесва с други отпадъци на работното място FIN !$!!7f6524j6.-64%0+.-6410+%0 Page SLO EU-Konformitätserklärung EU-Declaration of Conformity USA CDN USA CDN VDO Series Z